Using the original kernel for slackware 9.1, 2.4.22, I can plug in my sony camera and it detected it as a hotplug mass storage device. I had to recompile to use the rtl8180l and dropped my kernel version to 2.4.21.... now the question is, what to I need to enable in the 2.4.21 kernel to make it accept my camera, cause as of now it's spitting this out in dmesg...
Code:
host/uhci.c: 1060: wakeup_hc
host/uhci.c: root-hub INT complete: port1: 80 port2: 93 data: 4
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 101, change 0, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: new USB device 00:07.2-2, assigned address 2
usb.c: kmalloc IF d5e356a0, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: Sony
Product: Sony DSC
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0x54c/0x10) is not claimed by any active driver.
Length = 18
DescriptorType = 01
USB version = 1.10
Vendor:Product = 054c:0010
MaxPacketSize0 = 8
NumConfigurations = 1
Device version = 4.50
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = c0
MaxPower = 2mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = 08:ff:01
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 01 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 82 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0008
bInterval = ff
usb.c: kusbd: /sbin/hotplug add 2
SCSI subsystem driver Revision: 1.00
lsmod shows
Code:
root@flux:~# lsmod
Module Size Used by Tainted: GF
sd_mod 10924 0 (autoclean) (unused)
scsi_mod 87348 1 (autoclean) [sd_mod]
ymfpci 41896 0 (unused)
ac97_codec 11976 0 [ymfpci]
rtl8180_24x 244368 0
pcnet32 15328 1
Anyone have this problem? I've been comparing this kernel(2.4.21) against a tgz of the 2.4.22 one and I can't find where I am going wrong and what I need in it... any help would be appreciated. No I cannot upgrade my kernel version, this wireless driver requires 2.4.21 none of the other versions will work.
