Using *two* nearly identical ISAPNP sb16 soundcards

mgmax · 05-31-2006, 08:52 AM

Hi,

I wanted to set up a PC running Debian with two Soundblaster 16 Soundcards (Creative VIBRA 16X,VIBRA 16C).

With isapnp, pnpdump and alsaconfig I was only able to each of them working if I took the other card out, but only one of them if I put both in.

pnpdump sais:

Quote:

#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier 6d ff ff ff ff f0 00 8c 0e
# Board 2 has serial identifier e5 ff ff ff ff 70 00 8c 0e

# (DEBUG)
(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier 6d ff ff ff ff f0 00 8c 0e)
# Vendor Id CTL00f0, No Serial Number (-1), checksum 0x6D.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative ViBRA16X PnP<--
#
# Logical device id CTL0043
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00f0/-1 (LD 0
# ANSI string -->Audio<--

# Multiple choice time, choose one only !

# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 3))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

# Start dependent functions: priority functional
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0394
# IO base alignment 4 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

# Start dependent functions: priority functional
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

# End dependent functions
(NAME "CTL00f0/-1[0]{Audio }")
# (ACT Y)
))
#
# Logical device id CTL7005
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL00f0/-1 (LD 1
# Compatible device id PNPb02f
# ANSI string -->Game<--

# Multiple choice time, choose one only !

# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0201
# Maximum IO base address 0x0201
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0201))

# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x020f
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 0 (SIZE 1) (BASE 0x0200))

# End dependent functions
(NAME "CTL00f0/-1[1]{Game }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Card 2: (serial identifier e5 ff ff ff ff 70 00 8c 0e)
# Vendor Id CTL0070, No Serial Number (-1), checksum 0xE5.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative ViBRA16C PnP<--
#
# Logical device id CTL0001
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL0070/-1 (LD 0
# ANSI string -->Audio<--

# Multiple choice time, choose one only !

# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 5.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

# Start dependent functions: priority acceptable
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))

# Start dependent functions: priority functional
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

# Start dependent functions: priority functional
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (SIZE 2) (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (SIZE 4) (BASE 0x0388))

# Start dependent functions: priority functional
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0220))

# End dependent functions
(NAME "CTL0070/-1[0]{Audio }")
# (ACT Y)
))
#
# Logical device id CTL7001
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3d
# Device supports vendor reserved register @ 0x3f
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE CTL0070/-1 (LD 1
# Compatible device id PNPb02f
# ANSI string -->Game<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (SIZE 8) (BASE 0x0200))
(NAME "CTL0070/-1[1]{Game }")
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

my /etc/modutils/sound is:

Quote:

alias snd-card-0 snd-sb16
options snd-sb16 index=0,1
alias snd-card-1 snd-sb16

but aplay -l sais:

Quote:

serv1:/home/max# aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: S16 [Sound Blaster 16], device 0: SB16 DSP [DSP v4.16]
Subdevices: 1/1
Subdevice #0: subdevice #0

/var/log/messages sais nothing special about this and ISA in general.

What should I do?

Max