how to UBOOT a DM368 with no access to change boot mode

		LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
how to UBOOT a DM368 with no access to change boot mode

Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices

Welcome to LinuxQuestions.org, a friendly and active Linux Community.

You are currently viewing LQ as a guest. By joining our community you will have the ability to post topics, receive our newsletter, use the advanced search, subscribe to threads and access many other special features. Registration is quick, simple and absolutely free. Join our community today!

Note that registered members see fewer ads, and ContentLink is completely disabled once you log in.

Are you new to LinuxQuestions.org? Visit the following links:
Site Howto | Site FAQ | Sitemap | Register Now

If you have any problems with the registration process or your account login, please contact us. If you need to reset your password, click here.

Having a problem logging in? Please visit this page to clear all LQ-related cookies.

Get a virtual cloud desktop with the Linux distro that you want in less than five minutes with Shells! With over 10 pre-installed distros to choose from, the worry-free installation life is here! Whether you are a digital nomad or just looking for flexibility, Shells can put your Linux machine on the device that you want to use.

Exclusive for LQ members, get up to 45% off per month. Click here for more info.

Search this Thread

07-24-2023, 11:24 PM	#1
bozmanx105 LQ Newbie Registered: Jul 2023 Posts: 1 Rep:	how to UBOOT a DM368 with no access to change boot mode Hi all, new to this forum but not its products. This question kinda of spans both hardware and software so I chose here to post it. I have a board with a Ti dm368 with a NAND flash chip behind it. The UBOOT in the flash is bad and I can see this while connected to the UART. I do not have the ability to change the boot mode to UART as this process is not known for this board and there is no boot pins marked on it. Is there a way to UBOOT the dm368 without changing boot mode? There is also a JTAG and a 10 pin debug connection on the board. I was hoping that there might be a utility that allows direct interaction with the dm368 to be able to run the UBOOT. Any advice would be greatly appreciated. For reference the board is out of a GoPro Karma drone. GoPro support will not supply any information about the board or how to change boot mode.

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is Off HTML code is Off Forum Rules

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ethernet cable not getting detected on target leopard dm368	ranjana kumari	Linux - Software	2	07-19-2012 11:13 AM
not able to get ip address of leopard dm368 target board	ranjana kumari	Linux - Networking	0	07-19-2012 05:10 AM
setting Ip address on the target leopard dm368	ranjana kumari	Linux - Newbie	0	07-18-2012 04:19 AM
Linux Embedded programming books for TI DM368	javierhernandez	Linux - Newbie	2	09-12-2011 04:05 PM
How to enable bootloader-mode in Uboot 3.28 in LG-TV's?	Kristoffer G	Linux - Software	0	06-08-2011 03:34 PM

All times are GMT -5. The time now is 04:18 PM.

Main Menu

(Con't)

My LQ

Write for LQ

LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.

Main Menu

Syndicate

Latest Threads

LQ News

Twitter: @linuxquestions