[SOLVED] Has anyone sucessfully installed Linux on a Sabertooth 990FX?

genhappyok · 09-19-2011, 07:22 AM

Hello,

I recently purchased a ASUS Sabertooth 990FX motherboard to replace my aging tulatin system. The new system has an Phenom 1100t w 16GB of RAM. I recently updated the bios to the latest version 0705 (from 0402) which resolved my usb issues in linux. Heres my new issue:

This board has a Realtek 8111B NIC which isnt supported in any distro im aware of. Most will load the r8169 module which does not work. So i installed a Netgear FA311 into the pci slot which uses the NI Machphyter module which every distro uses. Now linux recognizes the FA311 but fails to connect via dhcp. lspci-v shows the correct module being loaded. Also this card has been verified working on 2 other machines. I also inserted a working GA311 netgear card to no avail. Without network support im kind of stuck in the water.

I have tried Arch Linux (installed no network (used dhcpcd eth0 -- looks for carrier and times out), Debian (this is the distro i want),Ubuntu and Slackware --no network on any of these using any network card i inserted.

To note: All the distros i tried is loading the correct module. I have two other systems that i use these cards in and have verified the module via lspci -v on all three machines.

This system has a UEFI bios, does that matter when the kernel looks at the hardware? (i know there is a EFI parameter in the kernel config which i will verify that its set). Do i need an efi capable nic card?

Anyone have any success with this board? I know Realtek supplies a driver for the onboard NIC which i havent tried yet. Im going to download it and compile it, but i heard its really buggy.

Thanks guys

Simon Bridge · 09-19-2011, 08:32 AM

You mean one of these??
It sounds like you have a successful gnu/linux install with some HW unsupported... is this correct?

Usually we want to you boot what you can and do an lspci - show us what it says.
In general, you should copy and paste what you get from commands rather than describing them.

Realtek 8111B NIC
The rtl8168/8111 driver is supposed to run this thing... according to Realtek this is.
http://www.linuxquestions.org/questi...nlinux-854790/
http://www.linuxquestions.org/questi...-linux-685748/
http://www.realtek.com.tw/downloads/...4&DownTypeID=3

Netgear FA311
detected and driver loaded - sounds like it is not set up as the default gateway.
use ifconfig to look at network devices (show us) ... you can probably get it set automatically if you disable the onboard nic (if you have that option).

genhappyok · 09-19-2011, 09:45 AM

Code:

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.0-ARCH (tobias@T-POWA-LX) (gcc version 4.6.1 (GCC) ) #1 SMP PREEMPT Wed Aug 17 21:55:57 CEST 2011
[    0.000000] Command line: root=/dev/disk/by-uuid/b955969d-6e55-47dc-8df0-4fb10322ea96 ro
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
[    0.000000]  BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bd837000 (usable)
[    0.000000]  BIOS-e820: 00000000bd837000 - 00000000bd888000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bd888000 - 00000000bd892000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bd892000 - 00000000bdade000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdade000 - 00000000bdaef000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdaef000 - 00000000bdb02000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdb02000 - 00000000bdb04000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdb04000 - 00000000bdb0d000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdb0d000 - 00000000bdb13000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdb13000 - 00000000bdb75000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdb75000 - 00000000bdd78000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdd78000 - 00000000bdf00000 (usable)
[    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec10000 - 00000000fec11000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec20000 - 00000000fec21000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed61000 - 00000000fed71000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed80000 - 00000000fed90000 (reserved)
[    0.000000]  BIOS-e820: 00000000fef00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100001000 - 0000000440000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.7 present.
[    0.000000] DMI: To be filled by O.E.M. To be filled by O.E.M./SABERTOOTH 990FX, BIOS 0705 08/22/2011
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x440000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF write-through
[    0.000000]   C0000-CCFFF write-protect
[    0.000000]   CD000-EBFFF uncachable
[    0.000000]   EC000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000BDF00000 mask FFFFFFF00000 uncachable
[    0.000000]   3 base 0000BE000000 mask FFFFFE000000 uncachable
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000440000000 aka 17408M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 00000000bdf00000 - 0000000100000000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0xbdf00 max_arch_pfn = 0x400000000
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: 0000000000000000-00000000bdf00000
[    0.000000]  0000000000 - 0080000000 page 1G
[    0.000000]  0080000000 - 00bde00000 page 2M
[    0.000000]  00bde00000 - 00bdf00000 page 4k
[    0.000000] kernel direct mapping tables up to bdf00000 @ bdefd000-bdf00000
[    0.000000] init_memory_mapping: 0000000100000000-0000000440000000
[    0.000000]  0100000000 - 0440000000 page 1G
[    0.000000] kernel direct mapping tables up to 440000000 @ 43ffff000-440000000
[    0.000000] RAMDISK: 37def000 - 37ff0000
[    0.000000] ACPI: RSDP 00000000000f0450 00024 (v02 ALASKA)
[    0.000000] ACPI: XSDT 00000000bd888068 0004C (v01 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI: FACP 00000000bd890c30 000F4 (v04 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20110413/tbfadt-560)
[    0.000000] ACPI: DSDT 00000000bd888140 08AED (v02 ALASKA    A M I 00000000 INTL 20051117)
[    0.000000] ACPI: FACS 00000000bdb0df80 00040
[    0.000000] ACPI: APIC 00000000bd890d28 0009E (v03 ALASKA    A M I 01072009 AMI  00010013)
[    0.000000] ACPI: MCFG 00000000bd890dc8 0003C (v01 ALASKA    A M I 01072009 MSFT 00010013)
[    0.000000] ACPI: HPET 00000000bd890e08 00038 (v01 ALASKA    A M I 01072009 AMI  00000004)
[    0.000000] ACPI: SSDT 00000000bd890e40 00E10 (v01 AMD    POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000440000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000440000000
[    0.000000]   NODE_DATA [000000043fffb000 - 000000043fffffff]
[    0.000000]  [ffffea0000000000-ffffea000edfffff] PMD -> [ffff88042f600000-ffff88043d5fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00440000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009e
[    0.000000]     0: 0x00000100 -> 0x000bd837
[    0.000000]     0: 0x000bdd78 -> 0x000bdf00
[    0.000000]     0: 0x00100001 -> 0x00440000
[    0.000000] On node 0 totalpages: 4184396
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3921 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 758263 pages, LIFO batch:31
[    0.000000]   Normal zone: 46592 pages used for memmap
[    0.000000]   Normal zone: 3361279 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x08] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x07] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 7, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec20000] gsi_base[24])
[    0.000000] IOAPIC[1]: apic_id 8, version 33, address 0xfec20000, GSI 24-55
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[    0.000000] SMP: Allowing 8 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 72
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bd837000 - 00000000bd888000
[    0.000000] PM: Registered nosave memory: 00000000bd888000 - 00000000bd892000
[    0.000000] PM: Registered nosave memory: 00000000bd892000 - 00000000bdade000
[    0.000000] PM: Registered nosave memory: 00000000bdade000 - 00000000bdaef000
[    0.000000] PM: Registered nosave memory: 00000000bdaef000 - 00000000bdb02000
[    0.000000] PM: Registered nosave memory: 00000000bdb02000 - 00000000bdb04000
[    0.000000] PM: Registered nosave memory: 00000000bdb04000 - 00000000bdb0d000
[    0.000000] PM: Registered nosave memory: 00000000bdb0d000 - 00000000bdb13000
[    0.000000] PM: Registered nosave memory: 00000000bdb13000 - 00000000bdb75000
[    0.000000] PM: Registered nosave memory: 00000000bdb75000 - 00000000bdd78000
[    0.000000] PM: Registered nosave memory: 00000000bdf00000 - 00000000f8000000
[    0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fc000000
[    0.000000] PM: Registered nosave memory: 00000000fc000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[    0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fec10000
[    0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fec11000
[    0.000000] PM: Registered nosave memory: 00000000fec11000 - 00000000fec20000
[    0.000000] PM: Registered nosave memory: 00000000fec20000 - 00000000fec21000
[    0.000000] PM: Registered nosave memory: 00000000fec21000 - 00000000fed00000
[    0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed01000
[    0.000000] PM: Registered nosave memory: 00000000fed01000 - 00000000fed61000
[    0.000000] PM: Registered nosave memory: 00000000fed61000 - 00000000fed71000
[    0.000000] PM: Registered nosave memory: 00000000fed71000 - 00000000fed80000
[    0.000000] PM: Registered nosave memory: 00000000fed80000 - 00000000fed90000
[    0.000000] PM: Registered nosave memory: 00000000fed90000 - 00000000fef00000
[    0.000000] PM: Registered nosave memory: 00000000fef00000 - 0000000100000000
[    0.000000] PM: Registered nosave memory: 0000000100000000 - 0000000100001000
[    0.000000] Allocating PCI resources starting at bdf00000 (gap: bdf00000:3a100000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff88043fc00000 s78464 r8192 d23936 u262144
[    0.000000] pcpu-alloc: s78464 r8192 d23936 u262144 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 4123463
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=/dev/disk/by-uuid/b955969d-6e55-47dc-8df0-4fb10322ea96 ro
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ f8000000 size 64 MB
[    0.000000] Memory: 16429532k/17825792k available (4064k kernel code, 1088208k absent, 308052k reserved, 3304k data, 712k init)
[    0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:2304
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 134217728 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 3311.293 MHz processor.
[    0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 6625.52 BogoMIPS (lpj=11037643)
[    0.003340] pid_max: default: 32768 minimum: 301
[    0.003433] Security Framework initialized
[    0.003437] AppArmor: AppArmor disabled by boot time parameter
[    0.004351] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.010458] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.012402] Mount-cache hash table entries: 256
[    0.012676] Initializing cgroup subsys cpuacct
[    0.012699] Initializing cgroup subsys memory
[    0.012711] Initializing cgroup subsys devices
[    0.012713] Initializing cgroup subsys freezer
[    0.012714] Initializing cgroup subsys net_cls
[    0.012716] Initializing cgroup subsys blkio
[    0.012751] tseg: 00bdf00000
[    0.012753] CPU: Physical Processor ID: 0
[    0.012754] CPU: Processor Core ID: 0
[    0.012755] mce: CPU supports 6 MCE banks
[    0.012763] using AMD E400 aware idle routine
[    0.013227] ACPI: Core revision 20110413
[    0.016679] ftrace: allocating 16144 entries in 64 pages
[    0.020162] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.053171] CPU0: AMD Phenom(tm) II X6 1100T Processor stepping 00
[    0.053330] Performance Events: AMD PMU driver.
[    0.053330] ... version:                0
[    0.053330] ... bit width:              48
[    0.053330] ... generic registers:      4
[    0.053330] ... value mask:             0000ffffffffffff
[    0.053330] ... max period:             00007fffffffffff
[    0.053330] ... fixed-purpose events:   0
[    0.053330] ... event mask:             000000000000000f
[    0.053330] System has AMD C1E enabled
[    0.053330] Switch to broadcast mode on CPU0
[    0.070037] NMI watchdog enabled, takes one hw-pmu counter.
[    0.096684] Booting Node   0, Processors  #1
[    0.096687] smpboot cpu 1: start_ip = 99000
[    0.193342] NMI watchdog enabled, takes one hw-pmu counter.
[    0.193340] Switch to broadcast mode on CPU1
[    0.213363]  #2
[    0.213365] smpboot cpu 2: start_ip = 99000
[    0.310009] NMI watchdog enabled, takes one hw-pmu counter.
[    0.309999] Switch to broadcast mode on CPU2
[    0.330020]  #3
[    0.330022] smpboot cpu 3: start_ip = 99000
[    0.426686] NMI watchdog enabled, takes one hw-pmu counter.
[    0.426676] Switch to broadcast mode on CPU3
[    0.446684]  #4
[    0.446686] smpboot cpu 4: start_ip = 99000
[    0.543350] NMI watchdog enabled, takes one hw-pmu counter.
[    0.543339] Switch to broadcast mode on CPU4
[    0.563351]  #5
[    0.563353] smpboot cpu 5: start_ip = 99000
[    0.660014] NMI watchdog enabled, takes one hw-pmu counter.
[    0.660003] Switch to broadcast mode on CPU5
[    0.666660] Brought up 6 CPUs
[    0.666663] Total of 6 processors activated (39749.41 BogoMIPS).
[    0.670201] devtmpfs: initialized
[    0.671484] PM: Registering ACPI NVS region at bd837000 (331776 bytes)
[    0.671484] PM: Registering ACPI NVS region at bdade000 (69632 bytes)
[    0.671484] PM: Registering ACPI NVS region at bdb02000 (8192 bytes)
[    0.671484] PM: Registering ACPI NVS region at bdb0d000 (24576 bytes)
[    0.671484] PM: Registering ACPI NVS region at bdb75000 (2109440 bytes)
[    0.671484] print_constraints: dummy: 
[    0.671484] NET: Registered protocol family 16
[    0.671484] node 0 link 0: io port [a000, ffff]
[    0.671484] TOM: 00000000c0000000 aka 3072M
[    0.671484] Fam 10h mmconf [e0000000, efffffff]
[    0.671484] node 0 link 0: mmio [c0000000, fef0ffff] ==> [c0000000, dfffffff] and [f0000000, fef0ffff]
[    0.671484] TOM2: 0000000440000000 aka 17408M
[    0.671484] bus: [00, 1f] on node 0 link 0
[    0.671484] bus: 00 index 0 [io  0x0000-0xffff]
[    0.671484] bus: 00 index 1 [mem 0xc0000000-0xdfffffff]
[    0.671484] bus: 00 index 2 [mem 0xf0000000-0xffffffff]
[    0.671484] bus: 00 index 3 [mem 0x440000000-0xfcffffffff]
[    0.671484] Extended Config Space enabled on 1 nodes
[    0.671484] ACPI: bus type pci registered
[    0.671484] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.671484] PCI: not using MMCONFIG
[    0.671484] PCI: Using configuration type 1 for base access
[    0.671484] PCI: Using configuration type 1 for extended access
[    0.671484] mtrr: your CPUs had inconsistent fixed MTRR settings
[    0.671484] mtrr: probably your BIOS does not setup all CPUs.
[    0.671484] mtrr: corrected configuration.
[    0.673433] bio: create slab <bio-0> at 0
[    0.673927] ACPI: EC: Look up EC in DSDT
[    0.674491] ACPI: Executed 2 blocks of module-level executable AML code
[    0.690065] ACPI Error: [RAMB] Namespace lookup failure, AE_NOT_FOUND (20110413/psargs-359)
[    0.690071] ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW] (Region) (20110413/nsinit-349)
[    0.690330] ACPI: Interpreter enabled
[    0.690333] ACPI: (supports S0 S1 S3 S4 S5)
[    0.690346] ACPI: Using IOAPIC for interrupt routing
[    0.690441] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.690468] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.781665] ACPI: EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
[    0.781757] ACPI: No dock devices found.
[    0.781758] HEST: Table not found.
[    0.781760] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.781849] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.781980] pci_root PNP0A03:00: host bridge window [io  0x0000-0x03af]
[    0.781981] pci_root PNP0A03:00: host bridge window [io  0x03e0-0x0cf7]
[    0.781983] pci_root PNP0A03:00: host bridge window [io  0x03b0-0x03df]
[    0.781984] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    0.781986] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.781987] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff]
[    0.781988] pci_root PNP0A03:00: host bridge window [mem 0xc0000000-0xffffffff]
[    0.781999] pci 0000:00:00.0: [1002:5a14] type 0 class 0x000600
[    0.782039] pci 0000:00:02.0: [1002:5a16] type 1 class 0x000604
[    0.782059] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[    0.782061] pci 0000:00:02.0: PME# disabled
[    0.782071] pci 0000:00:04.0: [1002:5a18] type 1 class 0x000604
[    0.782090] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[    0.782091] pci 0000:00:04.0: PME# disabled
[    0.782101] pci 0000:00:05.0: [1002:5a19] type 1 class 0x000604
[    0.782119] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[    0.782121] pci 0000:00:05.0: PME# disabled
[    0.782130] pci 0000:00:06.0: [1002:5a1a] type 1 class 0x000604
[    0.782148] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.782150] pci 0000:00:06.0: PME# disabled
[    0.782160] pci 0000:00:09.0: [1002:5a1c] type 1 class 0x000604
[    0.782179] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
[    0.782180] pci 0000:00:09.0: PME# disabled
[    0.782190] pci 0000:00:0b.0: [1002:5a1f] type 1 class 0x000604
[    0.782209] pci 0000:00:0b.0: PME# supported from D0 D3hot D3cold
[    0.782210] pci 0000:00:0b.0: PME# disabled
[    0.782228] pci 0000:00:11.0: [1002:4390] type 0 class 0x000101
[    0.782241] pci 0000:00:11.0: reg 10: [io  0xf090-0xf097]
[    0.782247] pci 0000:00:11.0: reg 14: [io  0xf080-0xf083]
[    0.782254] pci 0000:00:11.0: reg 18: [io  0xf070-0xf077]
[    0.782260] pci 0000:00:11.0: reg 1c: [io  0xf060-0xf063]
[    0.782267] pci 0000:00:11.0: reg 20: [io  0xf050-0xf05f]
[    0.782273] pci 0000:00:11.0: reg 24: [mem 0xf710b000-0xf710b3ff]
[    0.782287] pci 0000:00:11.0: set SATA to AHCI mode
[    0.782313] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03
[    0.782322] pci 0000:00:12.0: reg 10: [mem 0xf710a000-0xf710afff]
[    0.782369] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03
[    0.782382] pci 0000:00:12.2: reg 10: [mem 0xf7109000-0xf71090ff]
[    0.782429] pci 0000:00:12.2: supports D1 D2
[    0.782430] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.782433] pci 0000:00:12.2: PME# disabled
[    0.782447] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03
[    0.782456] pci 0000:00:13.0: reg 10: [mem 0xf7108000-0xf7108fff]
[    0.782503] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03
[    0.782516] pci 0000:00:13.2: reg 10: [mem 0xf7107000-0xf71070ff]
[    0.782564] pci 0000:00:13.2: supports D1 D2
[    0.782565] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[    0.782567] pci 0000:00:13.2: PME# disabled
[    0.782581] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[    0.782629] pci 0000:00:14.1: [1002:439c] type 0 class 0x000101
[    0.782638] pci 0000:00:14.1: reg 10: [io  0xf040-0xf047]
[    0.782645] pci 0000:00:14.1: reg 14: [io  0xf030-0xf033]
[    0.782651] pci 0000:00:14.1: reg 18: [io  0xf020-0xf027]
[    0.782658] pci 0000:00:14.1: reg 1c: [io  0xf010-0xf013]
[    0.782664] pci 0000:00:14.1: reg 20: [io  0xf000-0xf00f]
[    0.782689] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[    0.782703] pci 0000:00:14.2: reg 10: [mem 0xf7100000-0xf7103fff 64bit]
[    0.782742] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.782745] pci 0000:00:14.2: PME# disabled
[    0.782753] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601
[    0.782805] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[    0.782832] pci 0000:00:14.5: [1002:4399] type 0 class 0x000c03
[    0.782841] pci 0000:00:14.5: reg 10: [mem 0xf7106000-0xf7106fff]
[    0.782888] pci 0000:00:15.0: [1002:43a0] type 1 class 0x000604
[    0.782924] pci 0000:00:15.0: supports D1 D2
[    0.782940] pci 0000:00:15.1: [1002:43a1] type 1 class 0x000604
[    0.782976] pci 0000:00:15.1: supports D1 D2
[    0.782994] pci 0000:00:16.0: [1002:4397] type 0 class 0x000c03
[    0.783004] pci 0000:00:16.0: reg 10: [mem 0xf7105000-0xf7105fff]
[    0.783051] pci 0000:00:16.2: [1002:4396] type 0 class 0x000c03
[    0.783064] pci 0000:00:16.2: reg 10: [mem 0xf7104000-0xf71040ff]
[    0.783111] pci 0000:00:16.2: supports D1 D2
[    0.783112] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[    0.783114] pci 0000:00:16.2: PME# disabled
[    0.783127] pci 0000:00:18.0: [1022:1200] type 0 class 0x000600
[    0.783138] pci 0000:00:18.1: [1022:1201] type 0 class 0x000600
[    0.783147] pci 0000:00:18.2: [1022:1202] type 0 class 0x000600
[    0.783156] pci 0000:00:18.3: [1022:1203] type 0 class 0x000600
[    0.783166] pci 0000:00:18.4: [1022:1204] type 0 class 0x000600
[    0.783205] pci 0000:01:00.0: [10de:0402] type 0 class 0x000300
[    0.783213] pci 0000:01:00.0: reg 10: [mem 0xf6000000-0xf6ffffff]
[    0.783307] pci 0000:01:00.0: reg 14: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.783316] pci 0000:01:00.0: reg 1c: [mem 0xf4000000-0xf5ffffff 64bit]
[    0.783322] pci 0000:01:00.0: reg 24: [io  0xe000-0xe07f]
[    0.783327] pci 0000:01:00.0: reg 30: [mem 0xf7000000-0xf701ffff pref]
[    0.789969] pci 0000:00:02.0: PCI bridge to [bus 01-01]
[    0.789973] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.789976] pci 0000:00:02.0:   bridge window [mem 0xf4000000-0xf70fffff]
[    0.789979] pci 0000:00:02.0:   bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.790011] pci 0000:02:00.0: [197b:2362] type 0 class 0x000101
[    0.790032] pci 0000:02:00.0: reg 10: [io  0xd040-0xd047]
[    0.790042] pci 0000:02:00.0: reg 14: [io  0xd030-0xd033]
[    0.790052] pci 0000:02:00.0: reg 18: [io  0xd020-0xd027]
[    0.790061] pci 0000:02:00.0: reg 1c: [io  0xd010-0xd013]
[    0.790071] pci 0000:02:00.0: reg 20: [io  0xd000-0xd00f]
[    0.790080] pci 0000:02:00.0: reg 24: [mem 0xf7810000-0xf78101ff]
[    0.790090] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[    0.790114] pci 0000:02:00.0: PME# supported from D3hot
[    0.790117] pci 0000:02:00.0: PME# disabled
[    0.796637] pci 0000:00:04.0: PCI bridge to [bus 02-02]
[    0.796640] pci 0000:00:04.0:   bridge window [io  0xd000-0xdfff]
[    0.796642] pci 0000:00:04.0:   bridge window [mem 0xf7800000-0xf78fffff]
[    0.796645] pci 0000:00:04.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.796678] pci 0000:03:00.0: [197b:2362] type 0 class 0x000101
[    0.796700] pci 0000:03:00.0: reg 10: [io  0xc040-0xc047]
[    0.796709] pci 0000:03:00.0: reg 14: [io  0xc030-0xc033]
[    0.796719] pci 0000:03:00.0: reg 18: [io  0xc020-0xc027]
[    0.796729] pci 0000:03:00.0: reg 1c: [io  0xc010-0xc013]
[    0.796739] pci 0000:03:00.0: reg 20: [io  0xc000-0xc00f]
[    0.796748] pci 0000:03:00.0: reg 24: [mem 0xf7710000-0xf77101ff]
[    0.796758] pci 0000:03:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[    0.796782] pci 0000:03:00.0: PME# supported from D3hot
[    0.796786] pci 0000:03:00.0: PME# disabled

genhappyok · 09-19-2011, 09:48 AM

Code:

[    0.803303] pci 0000:00:05.0: PCI bridge to [bus 03-03]
[    0.803306] pci 0000:00:05.0:   bridge window [io  0xc000-0xcfff]
[    0.803308] pci 0000:00:05.0:   bridge window [mem 0xf7700000-0xf77fffff]
[    0.803311] pci 0000:00:05.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.803345] pci 0000:04:00.0: [1b21:1042] type 0 class 0x000c03
[    0.803361] pci 0000:04:00.0: reg 10: [mem 0xf7600000-0xf7607fff 64bit]
[    0.803431] pci 0000:04:00.0: PME# supported from D3hot D3cold
[    0.803434] pci 0000:04:00.0: PME# disabled
[    0.809969] pci 0000:00:06.0: PCI bridge to [bus 04-04]
[    0.809972] pci 0000:00:06.0:   bridge window [io  0xfff000-0x0000] (disabled)
[    0.809974] pci 0000:00:06.0:   bridge window [mem 0xf7600000-0xf76fffff]
[    0.809977] pci 0000:00:06.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.810011] pci 0000:05:00.0: [1b21:1042] type 0 class 0x000c03
[    0.810028] pci 0000:05:00.0: reg 10: [mem 0xf7500000-0xf7507fff 64bit]
[    0.810097] pci 0000:05:00.0: PME# supported from D3hot D3cold
[    0.810101] pci 0000:05:00.0: PME# disabled
[    0.816635] pci 0000:00:09.0: PCI bridge to [bus 05-05]
[    0.816639] pci 0000:00:09.0:   bridge window [io  0xfff000-0x0000] (disabled)
[    0.816641] pci 0000:00:09.0:   bridge window [mem 0xf7500000-0xf75fffff]
[    0.816644] pci 0000:00:09.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.816677] pci 0000:06:00.0: [14f1:8852] type 0 class 0x000400
[    0.816699] pci 0000:06:00.0: reg 10: [mem 0xf7200000-0xf73fffff 64bit]
[    0.816778] pci 0000:06:00.0: supports D1 D2
[    0.816779] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot
[    0.816784] pci 0000:06:00.0: PME# disabled
[    0.816802] pci 0000:06:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.816809] pci 0000:00:0b.0: PCI bridge to [bus 06-06]
[    0.816811] pci 0000:00:0b.0:   bridge window [io  0xfff000-0x0000] (disabled)
[    0.816813] pci 0000:00:0b.0:   bridge window [mem 0xf7200000-0xf73fffff]
[    0.816816] pci 0000:00:0b.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.816840] pci 0000:07:05.0: [100b:0020] type 0 class 0x000200
[    0.816857] pci 0000:07:05.0: reg 10: [io  0xb000-0xb0ff]
[    0.816866] pci 0000:07:05.0: reg 14: [mem 0xf7411000-0xf7411fff]
[    0.816908] pci 0000:07:05.0: reg 30: [mem 0xf7400000-0xf740ffff pref]
[    0.816926] pci 0000:07:05.0: supports D1 D2
[    0.816927] pci 0000:07:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.816931] pci 0000:07:05.0: PME# disabled
[    0.816948] pci 0000:07:07.0: [1106:3044] type 0 class 0x000c00
[    0.816966] pci 0000:07:07.0: reg 10: [mem 0xf7410000-0xf74107ff]
[    0.816976] pci 0000:07:07.0: reg 14: [io  0xb100-0xb17f]
[    0.817038] pci 0000:07:07.0: supports D2
[    0.817039] pci 0000:07:07.0: PME# supported from D2 D3hot D3cold
[    0.817043] pci 0000:07:07.0: PME# disabled
[    0.817080] pci 0000:00:14.4: PCI bridge to [bus 07-07] (subtractive decode)
[    0.817083] pci 0000:00:14.4:   bridge window [io  0xb000-0xbfff]
[    0.817086] pci 0000:00:14.4:   bridge window [mem 0xf7400000-0xf74fffff]
[    0.817089] pci 0000:00:14.4:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.817090] pci 0000:00:14.4:   bridge window [io  0x0000-0x03af] (subtractive decode)
[    0.817092] pci 0000:00:14.4:   bridge window [io  0x03e0-0x0cf7] (subtractive decode)
[    0.817093] pci 0000:00:14.4:   bridge window [io  0x03b0-0x03df] (subtractive decode)
[    0.817095] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.817096] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.817097] pci 0000:00:14.4:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.817099] pci 0000:00:14.4:   bridge window [mem 0xc0000000-0xffffffff] (subtractive decode)
[    0.817131] pci 0000:00:15.0: PCI bridge to [bus 08-08]
[    0.817135] pci 0000:00:15.0:   bridge window [io  0xfff000-0x0000] (disabled)
[    0.817138] pci 0000:00:15.0:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.817141] pci 0000:00:15.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.817188] pci 0000:09:00.0: [10ec:8168] type 0 class 0x000200
[    0.817202] pci 0000:09:00.0: reg 10: [io  0xa000-0xa0ff]
[    0.817226] pci 0000:09:00.0: reg 18: [mem 0xd0004000-0xd0004fff 64bit pref]
[    0.817241] pci 0000:09:00.0: reg 20: [mem 0xd0000000-0xd0003fff 64bit pref]
[    0.817283] pci 0000:09:00.0: supports D1 D2
[    0.817284] pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.817288] pci 0000:09:00.0: PME# disabled
[    0.823304] pci 0000:00:15.1: PCI bridge to [bus 09-09]
[    0.823309] pci 0000:00:15.1:   bridge window [io  0xa000-0xafff]
[    0.823312] pci 0000:00:15.1:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.823316] pci 0000:00:15.1:   bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.823340] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.823412] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[    0.823441] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE20._PRT]
[    0.823456] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE21._PRT]
[    0.823475] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC02._PRT]
[    0.823491] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC04._PRT]
[    0.823510] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC05._PRT]
[    0.823531] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC06._PRT]
[    0.823546] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC09._PRT]
[    0.823561] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC0B._PRT]
[    0.823577]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.823579]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.823580] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.827010] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 11 14 15) *0
[    0.827047] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 11 14 15) *0
[    0.827083] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 11 14 15) *0
[    0.827117] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 10 11 14 15) *0
[    0.827145] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 14 15) *0
[    0.827165] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 14 15) *0
[    0.827185] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7 10 11 14 15) *0
[    0.827204] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 14 15) *0
[    0.827261] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.827264] vgaarb: loaded
[    0.827265] vgaarb: bridge control possible 0000:01:00.0
[    0.827308] PCI: Using ACPI for IRQ routing
[    0.833112] PCI: pci_cache_line_size set to 64 bytes
[    0.833189] reserve RAM buffer: 000000000009ec00 - 000000000009ffff 
[    0.833190] reserve RAM buffer: 00000000bd837000 - 00000000bfffffff 
[    0.833192] reserve RAM buffer: 00000000bdf00000 - 00000000bfffffff 
[    0.833269] NetLabel: Initializing
[    0.833270] NetLabel:  domain hash size = 128
[    0.833271] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.833317] NetLabel:  unlabeled traffic allowed by default
[    0.833327] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.833330] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.835358] Switching to clocksource hpet
[    0.835370] Switched to NOHz mode on CPU #5
[    0.835416] Switched to NOHz mode on CPU #0
[    0.835361] Switched to NOHz mode on CPU #1
[    0.835366] Switched to NOHz mode on CPU #2
[    0.835370] Switched to NOHz mode on CPU #4
[    0.835366] Switched to NOHz mode on CPU #3
[    0.836586] pnp: PnP ACPI init
[    0.836594] ACPI: bus type pnp registered
[    0.836728] pnp 00:00: [bus 00-ff]
[    0.836730] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.836733] pnp 00:00: [io  0x0000-0x03af window]
[    0.836734] pnp 00:00: [io  0x03e0-0x0cf7 window]
[    0.836736] pnp 00:00: [io  0x03b0-0x03df window]
[    0.836737] pnp 00:00: [io  0x0d00-0xffff window]
[    0.836739] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.836740] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[    0.836742] pnp 00:00: [mem 0xc0000000-0xffffffff window]
[    0.836744] pnp 00:00: [mem 0x00000000 window]
[    0.836777] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.836799] pnp 00:01: [mem 0xe0000000-0xefffffff]
[    0.836834] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[    0.836836] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.836965] pnp 00:02: [io  0x040b]
[    0.836966] pnp 00:02: [io  0x04d6]
[    0.836968] pnp 00:02: [io  0x0c00-0x0c01]
[    0.836969] pnp 00:02: [io  0x0c14]
[    0.836970] pnp 00:02: [io  0x0c50-0x0c51]
[    0.836971] pnp 00:02: [io  0x0c52]
[    0.836972] pnp 00:02: [io  0x0c6c]
[    0.836974] pnp 00:02: [io  0x0c6f]
[    0.836975] pnp 00:02: [io  0x0cd0-0x0cd1]
[    0.836976] pnp 00:02: [io  0x0cd2-0x0cd3]
[    0.836977] pnp 00:02: [io  0x0cd4-0x0cd5]
[    0.836978] pnp 00:02: [io  0x0cd6-0x0cd7]
[    0.836980] pnp 00:02: [io  0x0cd8-0x0cdf]
[    0.836981] pnp 00:02: [io  0x0800-0x089f]
[    0.836983] pnp 00:02: [io  0x0000-0xffffffffffffffff disabled]
[    0.836984] pnp 00:02: [io  0x0000-0x000f]
[    0.836985] pnp 00:02: [io  0x0b20-0x0b3f]
[    0.836987] pnp 00:02: [io  0x0900-0x090f]
[    0.836988] pnp 00:02: [io  0x0910-0x091f]
[    0.836989] pnp 00:02: [io  0xfe00-0xfefe]
[    0.836990] pnp 00:02: [io  0x0060-0x005f disabled]
[    0.836992] pnp 00:02: [io  0x0064-0x0063 disabled]
[    0.836993] pnp 00:02: [mem 0xfec00000-0xfec00fff]
[    0.836995] pnp 00:02: [mem 0xfee00000-0xfee00fff]
[    0.836996] pnp 00:02: [mem 0xfed80000-0xfed8ffff]
[    0.836998] pnp 00:02: [mem 0xfed61000-0xfed70fff]
[    0.836999] pnp 00:02: [mem 0xfec10000-0xfec10fff]
[    0.837000] pnp 00:02: [mem 0xfed00000-0xfed00fff]
[    0.837002] pnp 00:02: [mem 0xffc00000-0xffffffff]
[    0.837063] system 00:02: [io  0x040b] has been reserved
[    0.837064] system 00:02: [io  0x04d6] has been reserved
[    0.837066] system 00:02: [io  0x0c00-0x0c01] has been reserved
[    0.837067] system 00:02: [io  0x0c14] has been reserved
[    0.837069] system 00:02: [io  0x0c50-0x0c51] has been reserved
[    0.837070] system 00:02: [io  0x0c52] has been reserved
[    0.837072] system 00:02: [io  0x0c6c] has been reserved
[    0.837073] system 00:02: [io  0x0c6f] has been reserved
[    0.837075] system 00:02: [io  0x0cd0-0x0cd1] has been reserved
[    0.837076] system 00:02: [io  0x0cd2-0x0cd3] has been reserved
[    0.837078] system 00:02: [io  0x0cd4-0x0cd5] has been reserved
[    0.837080] system 00:02: [io  0x0cd6-0x0cd7] has been reserved
[    0.837081] system 00:02: [io  0x0cd8-0x0cdf] has been reserved
[    0.837083] system 00:02: [io  0x0800-0x089f] has been reserved
[    0.837085] system 00:02: [io  0x0b20-0x0b3f] has been reserved
[    0.837086] system 00:02: [io  0x0900-0x090f] has been reserved
[    0.837088] system 00:02: [io  0x0910-0x091f] has been reserved
[    0.837090] system 00:02: [io  0xfe00-0xfefe] has been reserved
[    0.837092] system 00:02: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.837094] system 00:02: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.837095] system 00:02: [mem 0xfed80000-0xfed8ffff] has been reserved
[    0.837097] system 00:02: [mem 0xfed61000-0xfed70fff] has been reserved
[    0.837099] system 00:02: [mem 0xfec10000-0xfec10fff] has been reserved
[    0.837101] system 00:02: [mem 0xfed00000-0xfed00fff] has been reserved
[    0.837103] system 00:02: [mem 0xffc00000-0xffffffff] has been reserved
[    0.837104] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.837167] pnp 00:03: [io  0x0000-0xffffffffffffffff disabled]
[    0.837168] pnp 00:03: [io  0x0290-0x02af]
[    0.837170] pnp 00:03: [io  0x0000-0xffffffffffffffff disabled]
[    0.837196] system 00:03: [io  0x0290-0x02af] has been reserved
[    0.837198] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.837206] pnp 00:04: [dma 4]
[    0.837208] pnp 00:04: [io  0x0000-0x000f]
[    0.837209] pnp 00:04: [io  0x0081-0x0083]
[    0.837210] pnp 00:04: [io  0x0087]
[    0.837211] pnp 00:04: [io  0x0089-0x008b]
[    0.837212] pnp 00:04: [io  0x008f]
[    0.837213] pnp 00:04: [io  0x00c0-0x00df]
[    0.837226] pnp 00:04: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.837231] pnp 00:05: [io  0x0070-0x0071]
[    0.837237] pnp 00:05: [irq 8]
[    0.837250] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.837254] pnp 00:06: [io  0x0061]
[    0.837268] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.837280] pnp 00:07: [io  0x0010-0x001f]
[    0.837281] pnp 00:07: [io  0x0022-0x003f]
[    0.837282] pnp 00:07: [io  0x0044-0x005f]
[    0.837283] pnp 00:07: [io  0x0062-0x0063]
[    0.837284] pnp 00:07: [io  0x0065-0x006f]
[    0.837285] pnp 00:07: [io  0x0072-0x007f]
[    0.837286] pnp 00:07: [io  0x0080]
[    0.837288] pnp 00:07: [io  0x0084-0x0086]
[    0.837289] pnp 00:07: [io  0x0088]
[    0.837290] pnp 00:07: [io  0x008c-0x008e]
[    0.837291] pnp 00:07: [io  0x0090-0x009f]
[    0.837292] pnp 00:07: [io  0x00a2-0x00bf]
[    0.837293] pnp 00:07: [io  0x00e0-0x00ef]
[    0.837294] pnp 00:07: [io  0x04d0-0x04d1]
[    0.837330] system 00:07: [io  0x04d0-0x04d1] has been reserved
[    0.837332] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.837336] pnp 00:08: [io  0x00f0-0x00ff]
[    0.837339] pnp 00:08: [irq 13]
[    0.837353] pnp 00:08: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.837382] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.837393] pnp 00:0a: [io  0x0060]
[    0.837394] pnp 00:0a: [io  0x0064]
[    0.837397] pnp 00:0a: [irq 1]
[    0.837416] pnp 00:0a: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.837516] pnp 00:0b: [io  0x03f8-0x03ff]
[    0.837519] pnp 00:0b: [irq 4]
[    0.837520] pnp 00:0b: [dma 0 disabled]
[    0.837549] pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.837600] pnp 00:0c: [mem 0x00000000-0xffffffffffffffff disabled]
[    0.837629] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.837673] pnp 00:0d: [mem 0x00000000-0xffffffffffffffff disabled]
[    0.837675] pnp 00:0d: [mem 0xfec20000-0xfec200ff]
[    0.837703] system 00:0d: [mem 0xfec20000-0xfec200ff] could not be reserved
[    0.837705] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.837789] pnp 00:0e: [mem 0xfed00000-0xfed003ff]
[    0.837811] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.837814] pnp: PnP ACPI: found 15 devices
[    0.837815] ACPI: ACPI bus type pnp unregistered
[    0.843234] PCI: max bus depth: 1 pci_try_num: 2
[    0.843266] pci 0000:00:04.0: BAR 15: assigned [mem 0xd0100000-0xd01fffff pref]
[    0.843268] pci 0000:00:05.0: BAR 15: assigned [mem 0xd0200000-0xd02fffff pref]
[    0.843270] pci 0000:00:02.0: PCI bridge to [bus 01-01]
[    0.843272] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.843274] pci 0000:00:02.0:   bridge window [mem 0xf4000000-0xf70fffff]
[    0.843277] pci 0000:00:02.0:   bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.843280] pci 0000:02:00.0: BAR 6: assigned [mem 0xd0100000-0xd010ffff pref]
[    0.843282] pci 0000:00:04.0: PCI bridge to [bus 02-02]
[    0.843283] pci 0000:00:04.0:   bridge window [io  0xd000-0xdfff]
[    0.843286] pci 0000:00:04.0:   bridge window [mem 0xf7800000-0xf78fffff]
[    0.843288] pci 0000:00:04.0:   bridge window [mem 0xd0100000-0xd01fffff pref]
[    0.843291] pci 0000:03:00.0: BAR 6: assigned [mem 0xd0200000-0xd020ffff pref]
[    0.843292] pci 0000:00:05.0: PCI bridge to [bus 03-03]
[    0.843294] pci 0000:00:05.0:   bridge window [io  0xc000-0xcfff]
[    0.843296] pci 0000:00:05.0:   bridge window [mem 0xf7700000-0xf77fffff]
[    0.843298] pci 0000:00:05.0:   bridge window [mem 0xd0200000-0xd02fffff pref]
[    0.843301] pci 0000:00:06.0: PCI bridge to [bus 04-04]
[    0.843302] pci 0000:00:06.0:   bridge window [io  disabled]
[    0.843304] pci 0000:00:06.0:   bridge window [mem 0xf7600000-0xf76fffff]
[    0.843306] pci 0000:00:06.0:   bridge window [mem pref disabled]
[    0.843308] pci 0000:00:09.0: PCI bridge to [bus 05-05]
[    0.843309] pci 0000:00:09.0:   bridge window [io  disabled]
[    0.843311] pci 0000:00:09.0:   bridge window [mem 0xf7500000-0xf75fffff]
[    0.843313] pci 0000:00:09.0:   bridge window [mem pref disabled]
[    0.843315] pci 0000:00:0b.0: PCI bridge to [bus 06-06]
[    0.843317] pci 0000:00:0b.0:   bridge window [io  disabled]
[    0.843319] pci 0000:00:0b.0:   bridge window [mem 0xf7200000-0xf73fffff]
[    0.843320] pci 0000:00:0b.0:   bridge window [mem pref disabled]
[    0.843323] pci 0000:00:14.4: PCI bridge to [bus 07-07]
[    0.843325] pci 0000:00:14.4:   bridge window [io  0xb000-0xbfff]
[    0.843329] pci 0000:00:14.4:   bridge window [mem 0xf7400000-0xf74fffff]
[    0.843339] pci 0000:00:14.4:   bridge window [mem pref disabled]
[    0.843344] pci 0000:00:15.0: PCI bridge to [bus 08-08]
[    0.843345] pci 0000:00:15.0:   bridge window [io  disabled]
[    0.843348] pci 0000:00:15.0:   bridge window [mem disabled]
[    0.843350] pci 0000:00:15.0:   bridge window [mem pref disabled]
[    0.843354] pci 0000:00:15.1: PCI bridge to [bus 09-09]
[    0.843356] pci 0000:00:15.1:   bridge window [io  0xa000-0xafff]
[    0.843358] pci 0000:00:15.1:   bridge window [mem disabled]
[    0.843361] pci 0000:00:15.1:   bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.843371] pci 0000:00:02.0: PCI INT A -> GSI 52 (level, low) -> IRQ 52
[    0.843374] pci 0000:00:02.0: setting latency timer to 64
[    0.843377] pci 0000:00:04.0: PCI INT A -> GSI 52 (level, low) -> IRQ 52
[    0.843379] pci 0000:00:04.0: setting latency timer to 64
[    0.843382] pci 0000:00:05.0: PCI INT A -> GSI 52 (level, low) -> IRQ 52
[    0.843384] pci 0000:00:05.0: setting latency timer to 64
[    0.843388] pci 0000:00:06.0: PCI INT A -> GSI 53 (level, low) -> IRQ 53
[    0.843390] pci 0000:00:06.0: setting latency timer to 64
[    0.843393] pci 0000:00:09.0: PCI INT A -> GSI 53 (level, low) -> IRQ 53
[    0.843395] pci 0000:00:09.0: setting latency timer to 64
[    0.843399] pci 0000:00:0b.0: PCI INT A -> GSI 54 (level, low) -> IRQ 54
[    0.843401] pci 0000:00:0b.0: setting latency timer to 64
[    0.843408] pci 0000:00:15.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.843410] pci 0000:00:15.0: setting latency timer to 64
[    0.843414] pci 0000:00:15.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.843417] pci 0000:00:15.1: setting latency timer to 64
[    0.843419] pci_bus 0000:00: resource 4 [io  0x0000-0x03af]
[    0.843421] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7]
[    0.843422] pci_bus 0000:00: resource 6 [io  0x03b0-0x03df]
[    0.843424] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff]
[    0.843425] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[    0.843427] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
[    0.843428] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff]
[    0.843430] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.843431] pci_bus 0000:01: resource 1 [mem 0xf4000000-0xf70fffff]
[    0.843433] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.843434] pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
[    0.843436] pci_bus 0000:02: resource 1 [mem 0xf7800000-0xf78fffff]
[    0.843437] pci_bus 0000:02: resource 2 [mem 0xd0100000-0xd01fffff pref]
[    0.843439] pci_bus 0000:03: resource 0 [io  0xc000-0xcfff]
[    0.843440] pci_bus 0000:03: resource 1 [mem 0xf7700000-0xf77fffff]
[    0.843441] pci_bus 0000:03: resource 2 [mem 0xd0200000-0xd02fffff pref]
[    0.843443] pci_bus 0000:04: resource 1 [mem 0xf7600000-0xf76fffff]
[    0.843445] pci_bus 0000:05: resource 1 [mem 0xf7500000-0xf75fffff]
[    0.843446] pci_bus 0000:06: resource 1 [mem 0xf7200000-0xf73fffff]
[    0.843448] pci_bus 0000:07: resource 0 [io  0xb000-0xbfff]
[    0.843449] pci_bus 0000:07: resource 1 [mem 0xf7400000-0xf74fffff]
[    0.843450] pci_bus 0000:07: resource 4 [io  0x0000-0x03af]
[    0.843452] pci_bus 0000:07: resource 5 [io  0x03e0-0x0cf7]
[    0.843453] pci_bus 0000:07: resource 6 [io  0x03b0-0x03df]
[    0.843455] pci_bus 0000:07: resource 7 [io  0x0d00-0xffff]
[    0.843456] pci_bus 0000:07: resource 8 [mem 0x000a0000-0x000bffff]
[    0.843457] pci_bus 0000:07: resource 9 [mem 0x000c0000-0x000dffff]
[    0.843459] pci_bus 0000:07: resource 10 [mem 0xc0000000-0xffffffff]
[    0.843460] pci_bus 0000:09: resource 0 [io  0xa000-0xafff]
[    0.843462] pci_bus 0000:09: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[    0.843512] NET: Registered protocol family 2
[    0.843791] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.845246] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.847333] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.847587] TCP: Hash tables configured (established 524288 bind 65536)
[    0.847588] TCP reno registered
[    0.847605] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.847690] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.847942] NET: Registered protocol family 1
[    0.940155] pci 0000:01:00.0: Boot video device
[    0.940222] PCI: CLS 64 bytes, default 64
[    0.940259] Unpacking initramfs...
[    0.958954] Freeing initrd memory: 2052k freed
[    0.960706] PCI-DMA: Disabling AGP.
[    0.962808] PCI-DMA: aperture base @ f8000000 size 65536 KB
[    0.962810] init_memory_mapping: 00000000f8000000-00000000fc000000
[    0.962812]  00f8000000 - 00fc000000 page 2M
[    0.962816] PCI-DMA: using GART IOMMU.
[    0.962818] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    0.965961] audit: initializing netlink socket (disabled)
[    0.965974] type=2000 audit(1316338127.963:1): initialized
[    0.997075] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.059678] VFS: Disk quotas dquot_6.5.2
[    1.059773] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.059881] msgmni has been set to 32221
[    1.060137] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.060173] io scheduler noop registered
[    1.060174] io scheduler deadline registered
[    1.060206] io scheduler cfq registered (default)
[    1.060774] ERST: Table is not found!
[    1.060828] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.081329] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.304002] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.343568] Linux agpgart interface v0.103
[    1.343616] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    1.343617] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    1.343724] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.343774] mousedev: PS/2 mouse device common for all mice
[    1.343823] rtc_cmos 00:05: RTC can wake from S4
[    1.343895] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[    1.343912] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.343918] cpuidle: using governor ladder
[    1.343919] cpuidle: using governor menu
[    1.344064] TCP cubic registered
[    1.344066] NET: Registered protocol family 17
[    1.344071] Registering the dns_resolver key type
[    1.344126] PM: Hibernation image not present or could not be loaded.
[    1.344129] registered taskstats version 1
[    1.364570] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.375775] rtc_cmos 00:05: setting system clock to 2011-09-18 09:28:50 UTC (1316338130)
[    1.375821] Initializing network drop monitor service
[    1.376654] Freeing unused kernel memory: 712k freed
[    1.376831] Write protecting the kernel read-only data: 6144k
[    1.376960] Freeing unused kernel memory: 12k freed
[    1.378661] Freeing unused kernel memory: 776k freed
[    1.387156] udevd[108]: starting version 173
[    1.401448] SCSI subsystem initialized
[    1.405074] libata version 3.00 loaded.
[    1.407668] ahci 0000:00:11.0: version 3.0
[    1.407686] ahci 0000:00:11.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    1.407787] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[    1.407790] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part 
[    1.409215] scsi0 : ahci
[    1.409454] scsi1 : ahci
[    1.409505] scsi2 : ahci
[    1.409597] scsi3 : ahci
[    1.409755] ata1: SATA max UDMA/133 abar m1024@0xf710b000 port 0xf710b100 irq 19
[    1.409758] ata2: SATA max UDMA/133 abar m1024@0xf710b000 port 0xf710b180 irq 19
[    1.409761] ata3: SATA max UDMA/133 abar m1024@0xf710b000 port 0xf710b200 irq 19
[    1.409763] ata4: SATA max UDMA/133 abar m1024@0xf710b000 port 0xf710b280 irq 19
[    1.410088] ahci 0000:02:00.0: PCI INT A -> GSI 44 (level, low) -> IRQ 44
[    1.410162] ahci 0000:02:00.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[    1.410165] ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
[    1.410169] ahci 0000:02:00.0: setting latency timer to 64
[    1.411679] scsi4 : ahci
[    1.411806] usbcore: registered new interface driver usbfs
[    1.411824] usbcore: registered new interface driver hub
[    1.413088] scsi5 : ahci
[    1.413130] pata_atiixp 0000:00:14.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    1.413721] ata5: SATA max UDMA/133 abar m512@0xf7810000 port 0xf7810100 irq 44
[    1.413724] ata6: SATA max UDMA/133 abar m512@0xf7810000 port 0xf7810180 irq 44
[    1.413820] ahci 0000:03:00.0: PCI INT A -> GSI 46 (level, low) -> IRQ 46
[    1.413907] ahci 0000:03:00.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[    1.413910] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
[    1.413915] ahci 0000:03:00.0: setting latency timer to 64
[    1.413947] usbcore: registered new device driver usb
[    1.414214] scsi6 : pata_atiixp
[    1.414299] scsi7 : pata_atiixp
[    1.414680] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    1.414682] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    1.415578] scsi8 : ahci
[    1.415637] scsi9 : ahci
[    1.415907] ata9: SATA max UDMA/133 abar m512@0xf7710000 port 0xf7710100 irq 46
[    1.415910] ata10: SATA max UDMA/133 abar m512@0xf7710000 port 0xf7710180 irq 46
[    1.417516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.417636] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    1.417662] ehci_hcd 0000:00:12.2: EHCI Host Controller
[    1.417697] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[    1.417707] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.417725] QUIRK: Enable AMD PLL fix
[    1.417733] ehci_hcd 0000:00:12.2: debug port 1
[    1.417750] ehci_hcd 0000:00:12.2: irq 17, io mem 0xf7109000
[    1.426775] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    1.426868] hub 1-0:1.0: USB hub found
[    1.426872] hub 1-0:1.0: 5 ports detected
[    1.426976] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    1.427017] ehci_hcd 0000:00:13.2: EHCI Host Controller
[    1.427024] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[    1.427030] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.427046] ehci_hcd 0000:00:13.2: debug port 1
[    1.427061] ehci_hcd 0000:00:13.2: irq 21, io mem 0xf7107000
[    1.436773] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    1.436859] hub 2-0:1.0: USB hub found

genhappyok · 09-19-2011, 09:51 AM

Code:

[    1.436861] hub 2-0:1.0: 5 ports detected
[    1.436954] ehci_hcd 0000:00:16.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[    1.436966] ehci_hcd 0000:00:16.2: EHCI Host Controller
[    1.436972] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[    1.436978] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.436994] ehci_hcd 0000:00:16.2: debug port 1
[    1.437009] ehci_hcd 0000:00:16.2: irq 23, io mem 0xf7104000
[    1.446774] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[    1.446851] hub 3-0:1.0: USB hub found
[    1.446853] hub 3-0:1.0: 4 ports detected
[    1.514328] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.514529] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.514552] ohci_hcd 0000:00:12.0: OHCI Host Controller
[    1.514560] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[    1.514582] ohci_hcd 0000:00:12.0: irq 18, io mem 0xf710a000
[    1.570857] hub 4-0:1.0: USB hub found
[    1.570861] hub 4-0:1.0: 5 ports detected
[    1.571000] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    1.571012] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    1.571018] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[    1.571036] ohci_hcd 0000:00:13.0: irq 20, io mem 0xf7108000
[    1.627527] hub 5-0:1.0: USB hub found
[    1.627531] hub 5-0:1.0: 5 ports detected
[    1.627663] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.627675] ohci_hcd 0000:00:14.5: OHCI Host Controller
[    1.627681] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
[    1.627693] ohci_hcd 0000:00:14.5: irq 18, io mem 0xf7106000
[    1.684178] hub 6-0:1.0: USB hub found
[    1.684182] hub 6-0:1.0: 2 ports detected
[    1.684317] ohci_hcd 0000:00:16.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.684329] ohci_hcd 0000:00:16.0: OHCI Host Controller
[    1.684335] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
[    1.684353] ohci_hcd 0000:00:16.0: irq 22, io mem 0xf7105000
[    1.730116] ata2: SATA link down (SStatus 0 SControl 300)
[    1.730147] ata5: SATA link down (SStatus 0 SControl 300)
[    1.730154] ata10: SATA link down (SStatus 0 SControl 300)
[    1.730194] ata4: SATA link down (SStatus 0 SControl 300)
[    1.733469] ata6: SATA link down (SStatus 0 SControl 300)
[    1.740848] hub 7-0:1.0: USB hub found
[    1.740852] hub 7-0:1.0: 4 ports detected
[    1.893442] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.894321] ata1.00: ATA-7: ST3500630AS, 3.CHN, max UDMA/100
[    1.894323] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.895377] ata1.00: configured for UDMA/100
[    1.895540] scsi 0:0:0:0: Direct-Access     ATA      ST3500630AS      3.CH PQ: 0 ANSI: 5
[    1.896749] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.896928] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.897018] sd 0:0:0:0: [sda] Write Protect is off
[    1.897021] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.897048] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.897814] ata3.00: ATA-8: ST3500418AS, CC38, max UDMA/133
[    1.897816] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.899076] ata3.00: configured for UDMA/133
[    1.899214] scsi 2:0:0:0: Direct-Access     ATA      ST3500418AS      CC38 PQ: 0 ANSI: 5
[    1.899364] sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.899436] sd 2:0:0:0: [sdb] Write Protect is off
[    1.899438] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.899451] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.900070] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.900521] ata9.00: ATAPI: TSSTcorp DVD+/-RW TS-H653G, DW10, max UDMA/100
[    1.900524] ata9.00: applying bridge limits
[    1.901333] ata9.00: configured for UDMA/100
[    1.902768] scsi 8:0:0:0: CD-ROM            TSSTcorp DVD+-RW TS-H653G DW10 PQ: 0 ANSI: 5
[    1.903793]  sda: sda1 sda2
[    1.904059] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.927049]  sdb: sdb1 sdb2 sdb3 sdb4
[    1.927375] sd 2:0:0:0: [sdb] Attached SCSI disk
[    1.934312] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.934315] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.934426] sr 8:0:0:0: Attached scsi CD-ROM sr0
[    1.966744] Refined TSC clocksource calibration: 3311.115 MHz.
[    1.966749] Switching to clocksource tsc
[    2.330403] REISERFS (device sdb3): found reiserfs format "3.6" with standard journal
[    2.330410] REISERFS (device sdb3): using ordered data mode
[    2.339063] REISERFS (device sdb3): journal params: device sdb3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[    2.339450] REISERFS (device sdb3): checking transaction log (sdb3)
[    2.389038] REISERFS (device sdb3): Using r5 hash to sort names
[    3.083527] udevd[344]: starting version 173
[    3.146876] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.146893] r8169 0000:09:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    3.146952] r8169 0000:09:00.0: setting latency timer to 64
[    3.146958] r8169 0000:09:00.0: (unregistered net_device): unknown MAC, using family default
[    3.147018] r8169 0000:09:00.0: irq 72 for MSI/MSI-X
[    3.147205] r8169 0000:09:00.0: eth0: RTL8168b/8111b at 0xffffc900127c2000, 14:da:e9:09:46:57, XID 0c900800 IRQ 72
[    3.176706] ACPI: acpi_idle registered with cpuidle
[    3.176737] ACPI: processor limited to max C-state 1
[    3.180574] natsemi dp8381x driver, version 2.1, Sept 11, 2006
[    3.180575]   originally by Donald Becker <becker@scyld.com>
[    3.180576]   2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
[    3.180656] natsemi 0000:07:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    3.182708] natsemi eth1: NatSemi DP8381[56] at 0xf7411000 (0000:07:05.0), 00:0f:b5:42:e6:61, IRQ 20, port TP.
[    3.185985] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    3.185990] ACPI: Power Button [PWRB]
[    3.186043] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    3.186045] ACPI: Power Button [PWRF]
[    3.206633] input: PC Speaker as /devices/platform/pcspkr/input/input3
[    3.207144] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.207174] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    3.207198] sr 8:0:0:0: Attached scsi generic sg2 type 5
[    3.243612] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.281175] wmi: Mapper loaded
[    3.301071] MCE: In-kernel MCE decoding enabled.
[    3.378175] hda_codec: ALC892: BIOS auto-probing.
[    3.383397] firewire_ohci 0000:07:07.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    3.383680] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input4
[    3.388603] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 51 (level, low) -> IRQ 51
[    3.388643] xhci_hcd 0000:04:00.0: setting latency timer to 64
[    3.388647] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    3.388659] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 8
[    3.393033] xhci_hcd 0000:04:00.0: irq 51, io mem 0xf7600000
[    3.393115] xhci_hcd 0000:04:00.0: irq 73 for MSI/MSI-X
[    3.393117] xhci_hcd 0000:04:00.0: irq 74 for MSI/MSI-X
[    3.393119] xhci_hcd 0000:04:00.0: irq 75 for MSI/MSI-X
[    3.393122] xhci_hcd 0000:04:00.0: irq 76 for MSI/MSI-X
[    3.393124] xhci_hcd 0000:04:00.0: irq 77 for MSI/MSI-X
[    3.393126] xhci_hcd 0000:04:00.0: irq 78 for MSI/MSI-X
[    3.393128] xhci_hcd 0000:04:00.0: irq 79 for MSI/MSI-X
[    3.393257] xHCI xhci_add_endpoint called for root hub
[    3.393259] xHCI xhci_check_bandwidth called for root hub
[    3.393280] hub 8-0:1.0: USB hub found
[    3.393285] hub 8-0:1.0: 2 ports detected
[    3.393344] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    3.393363] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 9
[    3.393417] xHCI xhci_add_endpoint called for root hub
[    3.393418] xHCI xhci_check_bandwidth called for root hub
[    3.393437] hub 9-0:1.0: USB hub found
[    3.393441] hub 9-0:1.0: 2 ports detected
[    3.393489] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    3.393520] xhci_hcd 0000:05:00.0: PCI INT A -> GSI 48 (level, low) -> IRQ 48
[    3.393534] xhci_hcd 0000:05:00.0: setting latency timer to 64
[    3.393537] xhci_hcd 0000:05:00.0: xHCI Host Controller
[    3.393543] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 10
[    3.401296] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    3.403151] xhci_hcd 0000:05:00.0: irq 48, io mem 0xf7500000
[    3.403231] xhci_hcd 0000:05:00.0: irq 80 for MSI/MSI-X
[    3.403233] xhci_hcd 0000:05:00.0: irq 81 for MSI/MSI-X
[    3.403235] xhci_hcd 0000:05:00.0: irq 82 for MSI/MSI-X
[    3.403237] xhci_hcd 0000:05:00.0: irq 83 for MSI/MSI-X
[    3.403239] xhci_hcd 0000:05:00.0: irq 84 for MSI/MSI-X
[    3.403242] xhci_hcd 0000:05:00.0: irq 85 for MSI/MSI-X
[    3.403244] xhci_hcd 0000:05:00.0: irq 86 for MSI/MSI-X
[    3.403356] xHCI xhci_add_endpoint called for root hub
[    3.403357] xHCI xhci_check_bandwidth called for root hub
[    3.403375] hub 10-0:1.0: USB hub found
[    3.403379] hub 10-0:1.0: 2 ports detected
[    3.403418] xhci_hcd 0000:05:00.0: xHCI Host Controller
[    3.403422] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 11
[    3.403475] xHCI xhci_add_endpoint called for root hub
[    3.403476] xHCI xhci_check_bandwidth called for root hub
[    3.403492] hub 11-0:1.0: USB hub found
[    3.403496] hub 11-0:1.0: 2 ports detected
[    3.443473] firewire_ohci: Added fw-ohci device 0000:07:07.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x11
[    3.486201] asus_wmi: ASUS WMI generic driver loaded
[    3.486591] asus_wmi: Initialization: 0x0
[    3.486606] asus_wmi: BIOS WMI version: 0.9
[    3.486632] asus_wmi: SFUN value: 0x0
[    3.486805] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input5
[    3.514335] EDAC MC: Ver: 2.1.0
[    3.543387] [drm] Initialized drm 1.1.0 20060810
[    3.550321] Linux media interface: v0.10
[    3.550629] AMD64 EDAC driver v3.4.0
[    3.550736] EDAC amd64: DRAM ECC disabled.
[    3.550748] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[    3.550749]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[    3.550751]  (Note that use of the override may cause unknown side effects.)
[    3.552366] Linux video capture interface: v2.00
[    3.563792] MXM: GUID detected in BIOS
[    3.563873] nouveau 0000:01:00.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
[    3.563877] nouveau 0000:01:00.0: setting latency timer to 64
[    3.564860] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x084200a2)
[    3.567664] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
[    3.572272] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[    3.572325] SP5100 TCO timer: mmio address 0xbafe00 already in use
[    3.621353] [drm] nouveau 0000:01:00.0: ... appears to be valid
[    3.621355] [drm] nouveau 0000:01:00.0: BIT BIOS found
[    3.621357] [drm] nouveau 0000:01:00.0: Bios version 60.84.41.00
[    3.621359] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[    3.621360] [drm] nouveau 0000:01:00.0: BIT table 'd' not found
[    3.621361] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 4.0
[    3.621363] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000302 00000030
[    3.621365] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02000300 00000028
[    3.621366] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 02011312 00000030
[    3.621367] [drm] nouveau 0000:01:00.0: Raw DCB entry 3: 04011310 00000028
[    3.621368] [drm] nouveau 0000:01:00.0: Raw DCB entry 4: 010223f1 00c0c080
[    3.621370] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 14 2
[    3.621372] [drm] nouveau 0000:01:00.0:   0: 0x00001030: type 0x30 idx 0 tag 0x07
[    3.621373] [drm] nouveau 0000:01:00.0:   1: 0x00002130: type 0x30 idx 1 tag 0x08
[    3.621375] [drm] nouveau 0000:01:00.0:   2: 0x00000210: type 0x10 idx 2 tag 0xff
[    3.621376] [drm] nouveau 0000:01:00.0:   3: 0x00000211: type 0x11 idx 3 tag 0xff
[    3.621377] [drm] nouveau 0000:01:00.0:   4: 0x00000213: type 0x13 idx 4 tag 0xff
[    3.621380] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xBEDB
[    3.644592] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xC20E
[    3.661432] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xCC5B
[    3.661439] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xCD4D
[    3.662509] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xCF66
[    3.662510] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xCFCB
[    3.682516] [drm] nouveau 0000:01:00.0: 0xCFCB: Condition still not met after 20ms, skipping following opcodes
[    3.682527] [drm] nouveau 0000:01:00.0: timingset 255 does not exist
[    3.701302] [drm] nouveau 0000:01:00.0: 1 available performance level(s)
[    3.701305] [drm] nouveau 0000:01:00.0: 0: memory 700MHz core 540MHz shader 1188MHz voltage 1350mV fanspeed 100%
[    3.701319] [drm] nouveau 0000:01:00.0: c: memory 702MHz core 540MHz shader 1188MHz voltage 1350mV
[    3.701389] [TTM] Zone  kernel: Available graphics memory: 8249518 kiB.
[    3.701390] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB.
[    3.701391] [TTM] Initializing pool allocator.
[    3.701403] [drm] nouveau 0000:01:00.0: Detected 512MiB VRAM
[    3.705571] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[    3.718675] [drm] nouveau 0000:01:00.0: DCB encoder 1 unknown
[    3.718676] [drm] nouveau 0000:01:00.0: TV-1 has no encoders, removing
[    3.719278] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    3.719280] [drm] No driver support for vblank timestamp query.
[    3.750070] usb 8-2: new low speed USB device number 2 using xhci_hcd
[    3.776801] usb 8-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[    3.805541] altera_stapl: module is from the staging directory, the quality is unknown, you have been warned.
[    3.855706] xhci_hcd 0000:04:00.0: WARN: Stalled endpoint
[    3.862103] input: HID 1241:1177 as /devices/pci0000:00/0000:00:06.0/0000:04:00.0/usb8/8-2/8-2:1.0/input/input6

genhappyok · 09-19-2011, 09:52 AM

Code:

[    3.862175] generic-usb 0003:1241:1177.0001: input,hidraw0: USB HID v1.10 Mouse [HID 1241:1177] on usb-0000:04:00.0-2/input0
[    3.862186] usbcore: registered new interface driver usbhid
[    3.862187] usbhid: USB HID core driver
[    3.879977] [drm] nouveau 0000:01:00.0: allocated 1920x1080 fb: 0x40000000, bo ffff880424faec00
[    3.880039] fbcon: nouveaufb (fb0) is primary device
[    3.907134] cx23885 driver version 0.0.2 loaded
[    3.910060] cx23885 0000:06:00.0: PCI INT A -> GSI 32 (level, low) -> IRQ 32
[    3.910290] CORE cx23885[0]: subsystem: 0070:7911, board: Hauppauge WinTV-HVR1250 [card=3,autodetected]
[    3.910469] IR NEC protocol handler initialized
[    3.911283] IR RC5(x) protocol handler initialized
[    3.912122] IR RC6 protocol handler initialized
[    3.912962] IR JVC protocol handler initialized
[    3.913640] IR Sony protocol handler initialized
[    3.914914] lirc_dev: IR Remote Control driver registered, major 249 
[    3.915085] IR LIRC bridge handler initialized
[    3.926723] Console: switching to colour frame buffer device 240x67
[    3.928625] fb0: nouveaufb frame buffer device
[    3.928626] drm: registered panic notifier
[    3.928629] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0
[    3.943435] firewire_core: created device fw0: GUID 001fc6000014aafe, S400
[    4.045065] tveeprom 4-0050: Hauppauge model 79001, rev E1D9, serial# 3451608
[    4.045067] tveeprom 4-0050: MAC address is 00:0d:fe:34:aa:d8
[    4.045068] tveeprom 4-0050: tuner model is Microtune MT2131 (idx 139, type 4)
[    4.045070] tveeprom 4-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
[    4.045071] tveeprom 4-0050: audio processor is CX23885 (idx 39)
[    4.045073] tveeprom 4-0050: decoder processor is CX23885 (idx 33)
[    4.045074] tveeprom 4-0050: has no radio, has IR receiver, has no IR transmitter
[    4.045075] cx23885[0]: hauppauge eeprom: model=79001
[    4.045076] cx23885_dvb_register() allocating 1 frontend(s)
[    4.045078] cx23885[0]: cx23885 based dvb card
[    4.098427] MT2131: successfully identified at address 0x61
[    4.098430] DVB: registering new adapter (cx23885[0])
[    4.098432] DVB: registering adapter 0 frontend 0 (Samsung S5H1409 QAM/8VSB Frontend)...
[    4.098616] cx23885_dev_checkrevision() Hardware revision = 0xa4
[    4.098620] cx23885[0]/0: found at 0000:06:00.0, rev: 3, irq: 32, latency: 0, mmio: 0xf7200000
[    4.098625] cx23885 0000:06:00.0: setting latency timer to 64
[    4.666843] REISERFS (device sdb4): found reiserfs format "3.6" with standard journal
[    4.666854] REISERFS (device sdb4): using ordered data mode
[    4.673550] REISERFS (device sdb4): journal params: device sdb4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[    4.673951] REISERFS (device sdb4): checking transaction log (sdb4)
[    4.681949] REISERFS (device sdb4): Using r5 hash to sort names
[    4.741076] Adding 265068k swap on /dev/sdb2.  Priority:-1 extents:1 across:265068k

genhappyok · 09-19-2011, 09:53 AM

sorry guys i could have grepped this however i wanted someone to also check out the usb errors

genhappyok · 09-19-2011, 09:58 AM

Code:

00:00.0 Host bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx0 port B) (rev 02)
	Subsystem: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx0 port B)
	Flags: fast devsel
	Capabilities: [f0] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [c4] HyperTransport: Slave or Primary Interface
	Capabilities: [40] HyperTransport: Retry Mode
	Capabilities: [54] HyperTransport: UnitID Clumping
	Capabilities: [9c] HyperTransport: #1a
	Capabilities: [70] MSI: Enable- Count=1/4 Maskable- 64bit-

00:02.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port B) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: f4000000-f70fffff
	Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 5a14
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [190] Access Control Services
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:04.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port D) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: f7800000-f78fffff
	Prefetchable memory behind bridge: 00000000d0100000-00000000d01fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 5a14
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [190] Access Control Services
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:05.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port E) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 0000c000-0000cfff
	Memory behind bridge: f7700000-f77fffff
	Prefetchable memory behind bridge: 00000000d0200000-00000000d02fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 5a14
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [190] Access Control Services
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:06.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port F) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	Memory behind bridge: f7600000-f76fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 5a14
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [190] Access Control Services
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:09.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port H) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
	Memory behind bridge: f7500000-f75fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 5a14
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [190] Access Control Services
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:0b.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (NB-SB link) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
	Memory behind bridge: f7200000-f73fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot+), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 5a14
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Capabilities: [190] Access Control Services
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (rev 40) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. Device 84de
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 19
	I/O ports at f090 [size=8]
	I/O ports at f080 [size=4]
	I/O ports at f070 [size=8]
	I/O ports at f060 [size=4]
	I/O ports at f050 [size=16]
	Memory at f710b000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [70] SATA HBA v1.0
	Capabilities: [a4] PCI Advanced Features
	Kernel driver in use: ahci
	Kernel modules: ahci

00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
	Memory at f710a000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd

00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
	Memory at f7109000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 20
	Memory at f7108000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd

00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 21
	Memory at f7107000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42)
	Subsystem: ATI Technologies Inc SBx00 SMBus Controller
	Flags: 66MHz, medium devsel
	Kernel driver in use: piix4_smbus
	Kernel modules: i2c-piix4, sp5100_tco

00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) (prog-if 8a [Master SecP PriP])
	Subsystem: ASUSTeK Computer Inc. Device 84de
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
	I/O ports at 01f0 [size=8]
	I/O ports at 03f4 [size=1]
	I/O ports at 0170 [size=8]
	I/O ports at 0374 [size=1]
	I/O ports at f000 [size=16]
	Kernel driver in use: pata_atiixp
	Kernel modules: pata_atiixp, pata_acpi, ata_generic, atiixp, ide-pci-generic

00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40)
	Subsystem: ASUSTeK Computer Inc. Device 8436
	Flags: bus master, slow devsel, latency 32, IRQ 16
	Memory at f7100000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller
	Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) (prog-if 01 [Subtractive decode])
	Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency 64
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=64
	I/O behind bridge: 0000b000-0000bfff
	Memory behind bridge: f7400000-f74fffff

00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 18
	Memory at f7106000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd

00:15.0 PCI bridge: ATI Technologies Inc Device 43a0 (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot-), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 0000
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:15.1 PCI bridge: ATI Technologies Inc Device 43a1 (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
	I/O behind bridge: 0000a000-0000afff
	Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
	Capabilities: [50] Power Management version 3
	Capabilities: [58] Express Root Port (Slot-), MSI 00
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device 0000
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 22
	Memory at f7105000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd
	Kernel modules: ohci-hcd

00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 23
	Memory at f7104000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
	Flags: fast devsel
	Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
	Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
	Flags: fast devsel
	Kernel modules: amd64_edac_mod

00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
	Flags: fast devsel
	Capabilities: [f0] Secure device <?>
	Kernel driver in use: k10temp
	Kernel modules: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
	Flags: fast devsel

01:00.0 VGA compatible controller: nVidia Corporation G84 [GeForce 8600 GT] (rev a1) (prog-if 00 [VGA controller])
	Subsystem: ASUSTeK Computer Inc. Device 8243
	Flags: bus master, fast devsel, latency 0, IRQ 24
	Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
	Memory at c0000000 (64-bit, prefetchable) [size=256M]
	Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
	I/O ports at e000 [size=128]
	Expansion ROM at f7000000 [disabled] [size=128K]
	Capabilities: [60] Power Management version 2
	Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [78] Express Endpoint, MSI 00
	Capabilities: [100] Virtual Channel
	Capabilities: [128] Power Budgeting <?>
	Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
	Kernel driver in use: nouveau
	Kernel modules: nouveau, nvidiafb

02:00.0 SATA controller: JMicron Technology Corp. JMB362 AHCI Controller (rev 10) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
	Flags: bus master, fast devsel, latency 0, IRQ 44
	I/O ports at d040 [size=8]
	I/O ports at d030 [size=4]
	I/O ports at d020 [size=8]
	I/O ports at d010 [size=4]
	I/O ports at d000 [size=16]
	Memory at f7810000 (32-bit, non-prefetchable) [size=512]
	[virtual] Expansion ROM at d0100000 [disabled] [size=64K]
	Capabilities: [8c] Power Management version 3
	Capabilities: [50] Express Legacy Endpoint, MSI 00
	Kernel driver in use: ahci
	Kernel modules: ahci

03:00.0 SATA controller: JMicron Technology Corp. JMB362 AHCI Controller (rev 10) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard
	Flags: bus master, fast devsel, latency 0, IRQ 46
	I/O ports at c040 [size=8]
	I/O ports at c030 [size=4]
	I/O ports at c020 [size=8]
	I/O ports at c010 [size=4]
	I/O ports at c000 [size=16]
	Memory at f7710000 (32-bit, non-prefetchable) [size=512]
	[virtual] Expansion ROM at d0200000 [disabled] [size=64K]
	Capabilities: [8c] Power Management version 3
	Capabilities: [50] Express Legacy Endpoint, MSI 00
	Kernel driver in use: ahci
	Kernel modules: ahci

04:00.0 USB Controller: Device 1b21:1042 (prog-if 30 [XHCI])
	Subsystem: ASUSTeK Computer Inc. Device 8488
	Flags: bus master, fast devsel, latency 0, IRQ 51
	Memory at f7600000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
	Capabilities: [68] MSI-X: Enable+ Count=8 Masked-
	Capabilities: [78] Power Management version 3
	Capabilities: [80] Express Legacy Endpoint, MSI 00
	Capabilities: [100] Virtual Channel
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci-hcd

05:00.0 USB Controller: Device 1b21:1042 (prog-if 30 [XHCI])
	Subsystem: ASUSTeK Computer Inc. Device 8488
	Flags: bus master, fast devsel, latency 0, IRQ 48
	Memory at f7500000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+
	Capabilities: [68] MSI-X: Enable+ Count=8 Masked-
	Capabilities: [78] Power Management version 3
	Capabilities: [80] Express Legacy Endpoint, MSI 00
	Capabilities: [100] Virtual Channel
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci-hcd

06:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder (rev 03)
	Subsystem: Hauppauge computer works Inc. Device 7911
	Flags: bus master, fast devsel, latency 0, IRQ 32
	Memory at f7200000 (64-bit, non-prefetchable) [size=2M]
	Capabilities: [40] Express Endpoint, MSI 00
	Capabilities: [80] Power Management version 2
	Capabilities: [90] Vital Product Data
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [200] Virtual Channel
	Kernel driver in use: cx23885
	Kernel modules: cx23885

07:05.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
	Subsystem: Netgear FA311 / FA312 (FA311 with WoL HW)
	Flags: bus master, medium devsel, latency 32, IRQ 20
	I/O ports at b000 [size=256]
	Memory at f7411000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at f7400000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 2
	Kernel driver in use: natsemi
	Kernel modules: natsemi

07:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) (prog-if 10 [OHCI])
	Subsystem: ASUSTeK Computer Inc. M4A series motherboard
	Flags: bus master, medium devsel, latency 32, IRQ 22
	Memory at f7410000 (32-bit, non-prefetchable) [size=2K]
	I/O ports at b100 [size=128]
	Capabilities: [50] Power Management version 2
	Kernel driver in use: firewire_ohci
	Kernel modules: firewire-ohci

09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
	Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [Realtek RTL8111E]
	Flags: bus master, fast devsel, latency 0, IRQ 72
	I/O ports at a000 [size=256]
	Memory at d0004000 (64-bit, prefetchable) [size=4K]
	Memory at d0000000 (64-bit, prefetchable) [size=16K]
	Capabilities: [40] Power Management version 3
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
	Capabilities: [70] Express Endpoint, MSI 01
	Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
	Capabilities: [d0] Vital Product Data
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 01-00-00-00-68-4c-e0-00
	Kernel driver in use: r8169
	Kernel modules: r8169

genhappyok · 09-19-2011, 10:01 AM

Yes Simon it is. I did disable the onboiard Nic same problem. It tries to talk to the gate way but gets no response. This is happening in every distro i try from a live CD

Soadyheid · 09-19-2011, 10:31 AM

Linux on a Sabretooth... Naw, but check this out!

http://www.amazon.co.uk/Installing-L...6446173&sr=8-2

Play Bonny!

genhappyok · 09-19-2011, 12:38 PM

Looks like this is a hardware issue unfortunately. I got Parted Magic 3.7 to work with the GA311 (Part of UBCD 5.0). This really stinks. Oh well guess i should have did my research a little more.

Thanks for the help!!

cascade9 · 09-19-2011, 03:52 PM

Quote:

Originally Posted by genhappyok

This board has a Realtek 8111B NIC which isnt supported in any distro im aware of.

Its got a 8111'E', not 'B'-

Quote:

LAN Realtek® 8111E , 1 x Gigabit LAN Controller(s)

http://www.asus.com/Motherboards/AMD...specifications

It even says that in your lspci output-

Quote:

Originally Posted by genhappyok

Code:

09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
	Subsystem: ASUSTeK Computer Inc. P8P67 Deluxe Motherboard [Realtek RTL8111E]

I'm prety sure that one of the systems I've built lately had a 8111E that worked 'out of the box'. I'll need to go check the hardware to be sure, the manufacturer lists the networking chip as 8111D/E (meaning they could use either, depending on whats cheaper or in stock)

There are at least 2 motherboards listed in the HCL here with 8111E chips, and there are reviews on the net using linux with 8111E chips as well, so I dont think that is your problem...

BTW, are you actually running your HDDs in IDE mode?

Quote:

Originally Posted by genhappyok

Code:

00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (rev 40) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. Device 84de
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 19
	I/O ports at f090 [size=8]
	I/O ports at f080 [size=4]
	I/O ports at f070 [size=8]
	I/O ports at f060 [size=4]
	I/O ports at f050 [size=16]
	Memory at f710b000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [70] SATA HBA v1.0
	Capabilities: [a4] PCI Advanced Features
	Kernel driver in use: ahci
	Kernel modules: ahci

genhappyok · 09-19-2011, 08:14 PM

Cascade you are correct sorry for the typo, it loads the r8169 driver which does not work. As for IDE mode, yes i am because i had win xp installed on another drive and to save time from recreating an image with the ahci drivers, i just defaulted to ide. (i dont have a floppy anymore). A friend of mine here at work built the exact same setup except for the video card and he said ubuntu worked. i am stumped because i tried 3 different pci network cards that came out of my other linux boxes and they all act the same. If i load windows everything works. the only distro that has worked was partition magic 3.7 that came on the UBCD 5.0 recovery disc. I dont think i can RMA the board because it works fine in windows (im at work VNC'ing right into it as i type). Any suggestions would be great.Also i loaded the default bios settings to make sure i didnt mess anything up and have the same issues. I can get to the login screen but i have no usb and no network in linux (using the stock 3.03 kernel in arch and confirmed with latest debian slackware and ubuntu, and also this morning with BSD .

cascade9 · 09-20-2011, 05:07 AM

No problem with the typo, mistakes happen.

IDE mode cripples SATA drives in some ways, it disables SATA features like NCQ. Not that the board has floppy, so you'd need to use nLite or something similar to get the AHCI/SATA drivers into a XP disc.

I find it really odd that network cards you know are good with linux arent working either. But right now, I cant think of any reason why that would be the case.....hopefully when this damned headache goes away I'll think of something.

Simon Bridge · 09-20-2011, 12:08 PM

ifconfig

check the routing table.
Also - pick a distro: the one that you normally like which gets the most of the hardware going. This will let people trying to help you focus on specifics. It's no good trying to give you something to try only to find that you have changed install overnight.

Have a look at:
http://www.jamesonwilliams.com/hardy-r8168