Hey,
Just in case:
output of dmesg:
Linux version 2.6.11-1.1369_FC4 (bhcompile@decompose.build.redhat.com) (gcc version 4.0.0 20050525 (Red Hat 4.0.0-9)) #1 Thu Jun 2 22:55:56 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001beb0000 (usable)
BIOS-e820: 000000001beb0000 - 000000001beb8000 (ACPI data)
BIOS-e820: 000000001beb8000 - 000000001bf00000 (ACPI NVS)
BIOS-e820: 000000001bf00000 - 000000001c000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
446MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 114352
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 110256 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 TOSINV ) @ 0x000f7840
ACPI: RSDT (v001 TOSINV RSDT 0x06040000 LTP 0x00000000) @ 0x1beb42b0
ACPI: FADT (v001 TOSINV Goldfish 0x06040000 ATI 0x000f4240) @ 0x1beb7ef6
ACPI: MADT (v001 TOSINV APIC 0x06040000 LTP 0x00000000) @ 0x1beb7f6a
ACPI: MCFG (v001 TOSINV MCFG 0x06040000 LTP 0x00000000) @ 0x1beb7fc4
ACPI: SSDT (v001 TOSINV Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x1beb44e3
ACPI: SSDT (v001 TOSINV CpuPm 0x00003000 INTL 0x20030224) @ 0x1beb42e8
ACPI: DSDT (v001 TOSINV SB400 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 1c000000 (gap: 1c000000:c4000000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/1 rhgb quiet
Initializing CPU#0
CPU 0 irqstacks, hard=c0457000 soft=c0456000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1496.987 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447916k/457408k available (2518k kernel code, 8868k reserved, 690k data, 180k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2949.12 BogoMIPS (lpj=1474560)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9f3ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Celeron(R) M processor 1.50GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs... it is
Freeing initrd memory: 1081k freed
softlockup thread 0 started up.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd84c, last bus=4
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 7)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PFA1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x1080-0x1080 has been reserved
pnp: 00:07: ioport range 0x220-0x22f has been reserved
pnp: 00:07: ioport range 0x400-0x401 has been reserved
pnp: 00:07: ioport range 0x40b-0x40b has been reserved
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1121287590.948:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 42BD35A990375F72
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN1] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [TZCR] (53 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8430-0x8437, BIOS settings: hda
MA, hdb
io
ide1: BM-DMA at 0x8438-0x843f, BIOS settings: hdc
MA, hdd
io
Probing IDE interface ide0...
hda: FUJITSU MHV2080AH, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITADVD-RAM UJ-840S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 458752 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
LID OHC1 OHC2 EHCI P2P LANC AUDO MODM
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 180k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
Synaptics Touchpad, model: 1
Firmware: 6.2
180 degree mounted touchpad
Sensor: 37
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
synaptics: Toshiba Satellite detected, limiting rate to 40pps.
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda2: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 12259580
ext3_orphan_cleanup: deleting unreferenced inode 12257871
ext3_orphan_cleanup: deleting unreferenced inode 12257870
ext3_orphan_cleanup: deleting unreferenced inode 11829308
ext3_orphan_cleanup: deleting unreferenced inode 11829299
ext3_orphan_cleanup: deleting unreferenced inode 11829294
ext3_orphan_cleanup: deleting unreferenced inode 12652728
EXT3-fs: hda2: 7 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 6 roles, 824 types, 93 bools
security: 55 classes, 194544 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeling
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
floppy0: no floppy controllers found
ath_hal: no version for "struct_module" found: kernel tainted.
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
wlan: 0.8.4.5 (EXPERIMENTAL)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.12 (EXPERIMENTAL)
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 7.8 phy 4.5 radio 5.6
ath0: 802.11 address: 00:11:f5:6c:91:e0
ath0: Use hw queue 0 for WME_AC_BE traffic
ath0: Use hw queue 1 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Atheros 5212: mem=0xc0200000, irq=11
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xa000, 00:a0:d1:21:60:ca, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
snd_atiixp: Unknown parameter `'
ACPI: PCI Interrupt 0000:00:14.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 11, io mem 0xc0002000
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 11, io mem 0xc0000000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 11, io mem 0xc0001000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:06.0 [1179:ff10]
yenta 0000:02:06.0: Preassigned resource 0 busy, reconfiguring...
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x01111122, devctl 0x64
Yenta: ISA IRQ mask 0x04f8, PCI irq 11
Socket status: 30000006
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel@redhat.com
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 0
Buffer I/O error on device hdc, logical block 0
Buffer I/O error on device hdc, logical block 1
Buffer I/O error on device hdc, logical block 2
Buffer I/O error on device hdc, logical block 3
Buffer I/O error on device hdc, logical block 4
Buffer I/O error on device hdc, logical block 5
Buffer I/O error on device hdc, logical block 6
Buffer I/O error on device hdc, logical block 7
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 0
Buffer I/O error on device hdc, logical block 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 03 92 80 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 936448
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 0
Buffer I/O error on device hdc, logical block 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 03 92 80 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 936448
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 0
EXT3 FS on hda2, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 530136k swap on /dev/hda3. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (3573 buckets, 28584 max) - 272 bytes per conntrack
cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf 0xcf8-0xcff
cs: IO port probe 0x800-0x8ff: excluding 0x878-0x87f
cs: IO port probe 0x100-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
eth0: link down
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
i2c /dev entries driver
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03e6820(lo)
IPv6 over IPv4 tunneling driver
ath0: no IPv6 routers present
audit(:1093177): major=252 name_count=0: freeing multiple contexts (1)