Share your knowledge at the LQ Wiki.
Go Back > Blogs
User Name


  1. Old Comment

    Persistent naming with multiple internal drives in Slackware

    Good on you for persisting (sorry ) with this. In choosing such a task, and seeing it through to the end you've earned your stripes, in my opinion. I can sense it. You're already a slacker through-and-through.

    Welcome to Slackware! Or, more correctly, Welcome Home.
    Posted Today at 08:21 PM by rkelsen rkelsen is online now
  2. Old Comment

    u-boot is infuriating

    Ok, a bit of fudging stuff around and I think I have this figured out. The Raspberry Pi 3 B+ has the magic boot bits set to boot from usb0, however, I haven't been able to get the OpenBSD bootloader to load a kernel from an FFS filesystem at the boot> prompt if I boot from usb0 (mmc0 loads just fine, however).

    So I dd'd the latest miniroot63.fs to an sd card, then disklabel'd the sd card and deleted the 'a' partition. I edited the sd card with fdisk and grew out the OpenBSD partition to the full remainder of the sd card after the msdos partition. Once that was done, I disklabel -dE'd the sd card and created an 'a' partition that took up the entire OpenBSD area. Once that was done, I dd'd the first 4 MB of the miniroot back to the sd card, ftp'd the bsd* files for arm64 to the sd0a partition, and booted the pi up with my franken-sd.

    Now at the boot> prompt I can select any of the bsd* files I copied to the sd0a partition, so I obviously select the bsd.rd file, install to my external SATA drive. I reboot, catch the ddb error about the duid it can't find (and copy that to a safe location), then boot back up to bsd.rd, disklabel -E sd0 and update the duid ('i'), edit /etc/fstab to use the new duid, and...

    Then I cross my fingers and reboot!


    NOTE: this approach basically disables any advantage you would get from kernel re-linking! And updating this franken-sd isn't going to be fun =\
    Posted 08-09-2018 at 11:47 AM by rocket357 rocket357 is offline
  3. Old Comment

    The little outlet that couldn't

    Yeah, once I figured that part out it was pretty clear why certain outlets failed when what seemed like an unrelated room had a power issue.
    Posted 08-08-2018 at 11:11 PM by rocket357 rocket357 is offline
  4. Old Comment

    u-boot is infuriating

    Bit the bullet and picked up one of these:

    Shows up as:

    axen0 at uhub1 port 2 configuration 1 interface 0 "ASIX Elec. Corp. AX88179" rev 2.10/1.00 addr 4
    axen0: AX88179, address xx:xx:xx:xx:xx:xx
    rgephy0 at axen0 phy 3: RTL8169S/8110S/8211 PHY, rev. 5
    Posted 08-08-2018 at 10:52 PM by rocket357 rocket357 is offline
  5. Old Comment

    The little outlet that couldn't

    My house is wired that way. The circuit breakers follow the construction of the house and not the rooms.
    Posted 08-08-2018 at 04:05 PM by vmccord vmccord is offline
  6. Old Comment

    15-year-old desktop kept alive with Debian 9 and Xfce (but not GNOME)

    Bumblebee display driver displaces Nouveau -- no crashes since

    To recap, after I upgraded my 15-year-old-desktop machine (Pogo2003) to Debian 9.4 from 8.10, I started having regular crashes, frequently but not always after resizing a window. I was running the Xfce desktop environment. I tried adding LXDE to see if the culprit was the DE. It wasn't -- the crashes continued under LXDE as well as Xfce.

    The latest thing I did was install the Bumblebee graphics display driver from the Debian repository. So far I have not had a crash since the Bumblebee install. Guess I'll give it a month or so before claiming problem solved, but I am optimistic.
    Posted 07-31-2018 at 06:41 PM by flshope flshope is offline
    Updated 08-05-2018 at 06:20 PM by flshope
  7. Old Comment

    ExTiX 18.7 – “The Ultimate Linux System” – with LXQt 0.12.0, Refracta Tools, Calamares Installer and kernel 4.18.0-rc5-extix – Build 180723

    Softpedia 180724: ExTiX "The Ultimate Linux System" Now Uses Linux 4.18, Based on Ubuntu 18.04.1 LTS

    "Based on packages from the Ubuntu 18.04.1 LTS ("Bionic Beaver") and Debian GNU/Linux 9 "Stretch" operating system series, ExTiX 18.7 is the first release of the GNU/Linux distribution to use the forthcoming Linux 4.18 kernel series, which is currently in development and should hit the streets early next month.

    Arne Exton was brave enough to rebase his ExTiX Linux operating system on the fifth Release Candidate of Linux kernel 4.18, which is patched to allow the installation of Nvidia’s proprietary graphics drivers. Arne Exton's 4.18.0-rc5-extix kernel replaces kernel 4.16.2-exton used in the previous release, but it's an unstable kernel".

    Posted 07-27-2018 at 12:10 PM by exton exton is offline
  8. Old Comment

    ExTiX 18.7 – “The Ultimate Linux System” – with LXQt 0.12.0, Refracta Tools, Calamares Installer and kernel 4.18.0-rc5-extix – Build 180723

    ExTiX 18.7 is now on the front page at That will surely increase the download numbers. Dramatically.

    Posted 07-23-2018 at 02:56 PM by exton exton is offline


All times are GMT -5. The time now is 09:18 PM.

Main Menu
Write for LQ is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration