LinuxQuestions.org
Download your favorite Linux distribution at LQ ISO.
Home Forums Tutorials Articles Register
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware
Reload this Page slack 12.1 behind hub won't connect on internet while slack 11 does
User Name
Password
Slackware This Forum is for the discussion of Slackware Linux.

Notices


Reply
  Search this Thread
Old 08-01-2008, 12:13 AM   #1
CesarLG
LQ Newbie
 
Registered: Jul 2008
Distribution: Slackware 12.1
Posts: 12

Rep: Reputation: 0
slack 12.1 behind hub won't connect on internet while slack 11 does

Hello, everyone.

I'm not exactly a noob, but I'm not far from it.

I've been reading around and found similar problems, but nothing helped me. After much experimenting and probably messing it up even more, I've just re-installed slack 12.1 on another hd and I kept my slack 11 working on hda.
I've tried before to install slack 12 and 12.1 but I can only get internet to work with slack 11. I know about the similar treads, but I really couldn't figure it out. It's one computer, two slacks. Why I can't connect with slack 12.1?

I'm really out of ideas here. So, please, if you may...

Thanks for all!

Here is my ifconfig -a on slack 12.1
Code:
root@darkstar:~# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:02:44:8d:da:cf
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:5356 (5.2 KiB)
          Interrupt:22 Base address:0xe400

eth1      Link encap:Ethernet  HWaddr 00:13:d4:62:eb:ac
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:23 Base address:0xe000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:112 errors:0 dropped:0 overruns:0 frame:0
          TX packets:112 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:8192 (8.0 KiB)  TX bytes:8192 (8.0 KiB)
and here my ifconfig -a on slack 11
Code:
eth0      Link encap:Ethernet  HWaddr 00:13:D4:62:EB:AC
          inet addr:189.32.122.20  Bcast:255.255.255.255  Mask:255.255.224.0
          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:97698 errors:1 dropped:0 overruns:0 frame:0
          TX packets:2472 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:7355612 (7.0 MiB)  TX bytes:550275 (537.3 KiB)
          Interrupt:10 Base address:0x7400

eth1      Link encap:Ethernet  HWaddr 00:02:44:8D:DA:CF
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:5 Base address:0x9c00

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:446 (446.0 b)  TX bytes:446 (446.0 b)
Now route -n on slack 12.1
Code:
root@darkstar:~# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
And route -n on slack 11.
Code:
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
189.32.96.0     0.0.0.0         255.255.224.0   U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         189.32.96.1     0.0.0.0         UG    0      0        0 eth0
 
Old 08-01-2008, 12:14 AM   #2
CesarLG
LQ Newbie
 
Registered: Jul 2008
Distribution: Slackware 12.1
Posts: 12

Original Poster
Rep: Reputation: 0
And dmesg on slack 12.1

Code:
root@darkstar:~# dmesg
Linux version 2.6.24.5-smp (root@midas) (gcc version 4.2.3) #2 SMP Wed Apr 30 13:41:38 CDT 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003df30000 (usable)
 BIOS-e820: 000000003df30000 - 000000003df40000 (ACPI data)
 BIOS-e820: 000000003df40000 - 000000003dff0000 (ACPI NVS)
 BIOS-e820: 000000003dff0000 - 000000003e000000 (reserved)
 BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
95MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 253744) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   253744
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   253744
On node 0 totalpages: 253744
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 190 pages used for memmap
  HighMem zone: 24178 pages, LIFO batch:3
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000FAD90, 0014 (r0 ACPIAM)
ACPI: RSDT 3DF30000, 0030 (r1 A M I  OEMRSDT   6000527 MSFT       97)
ACPI: FACP 3DF30200, 0081 (r2 A M I  OEMFACP   6000527 MSFT       97)
ACPI: DSDT 3DF303F0, 35BE (r1  100XX 100XX001        1 INTL  2002026)
ACPI: FACS 3DF40000, 0040
ACPI: APIC 3DF30390, 005C (r1 A M I  OEMAPIC   6000527 MSFT       97)
ACPI: OEMB 3DF40040, 0040 (r1 A M I  AMI_OEM   6000527 MSFT       97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3e000000:c17c0000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e8000
swsusp: Registered nosave memory region: 00000000000e8000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 251762
Kernel command line: initrd=initrd.img load_ramdisk=1 prompt_ramdisk=0 rw SLACK_KERNEL=hugesmp.s BOOT_IMAGE=/kernels/hugesmp.s/bzImage root=/dev/hdc2 rdinit= ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2653.655 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 982948k/1014976k available (6059k kernel code, 31392k reserved, 2015k data, 380k init, 97472k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe15000 - 0xfffff000   (1960 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc08ed000 - 0xc094c000   ( 380 kB)
      .data : 0xc06eadca - 0xc08e2cfc   (2015 kB)
      .text : 0xc0100000 - 0xc06eadca   (6059 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 5311.15 BogoMIPS (lpj=10622317)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 20000000 00000000 0000b180 0000651d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 24k freed
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 01
Total of 1 processors activated (5311.15 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 64 bytes
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  4263.000 MB/sec
xor: using function: pIII_sse (4263.000 MB/sec)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] -  D8, should be C9 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x290-0x297 has been reserved
system 00:0a: ioport range 0x480-0x48f has been reserved
system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0x800-0x8df has been reserved
system 00:0a: ioport range 0x8e0-0x8ff has been reserved
system 00:0a: iomem range 0xffe80000-0xffefffff could not be reserved
system 00:0b: ioport range 0x900-0x90f has been reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:0e: iomem range 0x0-0x9ffff could not be reserved
system 00:0e: iomem range 0xc0000-0xdffff could not be reserved
system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
system 00:0e: iomem range 0x100000-0x3dfeffff could not be reserved
system 00:0e: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: dfe00000-dfefffff
  PREFETCH window: cfd00000-dfcfffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 13494k freed
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.29 [Flags: R/W].
JFS: nTxBlock = 7786, nTxLock = 62295
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
GFS2 (built Apr 30 2008 13:40:39) installed
async_tx: api initialized (async)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
input: Macintosh mouse button emulation as /devices/virtual/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller (0x1039:0x5513 rev 0x01) at  PCI slot 0000:00:02.5
ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: TSSTcorpCD-R/RW SH-R522C, ATAPI CD/DVD-ROM drive
hda: ST380011A, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: WDC WD102AA, ATA DISK drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: host side 80-wire cable detection failed, limiting max speed to UDMA33
hdc: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63
hda: cache flushes supported
 hda: hda1 hda2 hda3
hdc: max request size: 128KiB
hdc: 20044080 sectors (10262 MB) w/2048KiB Cache, CHS=19885/16/63
hdc: cache flushes not supported
 hdc: hdc1 hdc2
hdb: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
Loading iSCSI transport class v2.0-724.
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2449]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.2
Copyright(c) 2004-2007 Emulex.  All rights reserved.
seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
DC390: clustering now enabled by default. If you get problems load
        with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx SATA Controller driver v1.2 (070830)
st: Version 20070203, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
sata_sis 0000:00:05.0: version 1.0
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 17
sata_sis 0000:00:05.0: Detected SiS 180/181/964 chipset in SATA mode
scsi2 : sata_sis
scsi3 : sata_sis
ata1: SATA max UDMA/133 cmd 0xeff0 ctl 0xefe4 bmdma 0xef90 irq 17
ata2: SATA max UDMA/133 cmd 0xefa8 ctl 0xefe0 bmdma 0xef98 irq 17
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
Fusion MPT FC Host driver 3.04.06
Fusion MPT SAS Host driver 3.04.06
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 18
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: irq 18, io mem 0xdffff000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 19
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 19, io mem 0xdfffc000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 20, io mem 0xdfffd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 21, io mem 0xdfffe000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    718 MB/s
raid6: int32x2    788 MB/s
raid6: int32x4    794 MB/s
raid6: int32x8    560 MB/s
raid6: mmxx1     1608 MB/s
raid6: mmxx2     1888 MB/s
raid6: sse1x1     952 MB/s
raid6: sse1x2    1669 MB/s
raid6: sse2x1    1922 MB/s
raid6: sse2x2    2760 MB/s
raid6: using algorithm sse2x2 (2760 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 380k freed
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 22
eth0: RealTek RTL8139 at 0xe400, 00:02:44:8d:da:cf, IRQ 22
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 23
eth1: RealTek RTL8139 at 0xe000, 00:13:d4:62:eb:ac, IRQ 23
eth1:  Identified 8139 chip type 'RTL-8100B/8139D'
Linux agpgart interface v0.102
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
agpgart: Detected SiS chipset - id:1633
agpgart: AGP aperture is 64M @ 0xe0000000
rtc_cmos: probe of 00:02 failed with error -16
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
input: Power Button (FF) as /devices/virtual/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 22
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
intel8x0_measure_ac97_clock: measured 54818 usecs
intel8x0: clocking to 48000
Adding 634496k swap on /dev/hdc1.  Priority:-1 extents:1 across:634496k
fuse init (API version 7.9)
EXT3 FS on hdc2, internal journal
lp0: using parport0 (interrupt-driven).
lp0: console ready
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
hdb: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdb: media error (bad sector): error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdb:
  Error: Medium error -- (Sense key=0x03)
  (reserved error code) -- (asc=0x02, ascq=0x00)
  The failed "Read 10" packet command was:
  "28 00 00 00 00 10 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdb, sector 64
Buffer I/O error on device hdb, logical block 8
hdb: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdb: media error (bad sector): error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdb:
  Error: Medium error -- (Sense key=0x03)
  (reserved error code) -- (asc=0x02, ascq=0x00)
  The failed "Read 10" packet command was:
  "28 00 00 00 00 10 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdb, sector 64
Buffer I/O error on device hdb, logical block 8
hdb: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdb: media error (bad sector): error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdb:
  Error: Medium error -- (Sense key=0x03)
  (reserved error code) -- (asc=0x02, ascq=0x00)
  The failed "Read 10" packet command was:
  "28 00 00 00 00 10 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdb, sector 64
Buffer I/O error on device hdb, logical block 8
hdb: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hdb: media error (bad sector): error=0x34 { AbortedCommand LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hdb:
  Error: Medium error -- (Sense key=0x03)
  (reserved error code) -- (asc=0x02, ascq=0x00)
  The failed "Read 10" packet command was:
  "28 00 00 00 00 10 00 00 02 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdb, sector 64
Buffer I/O error on device hdb, logical block 8
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
 
Old 08-01-2008, 12:15 AM   #3
CesarLG
LQ Newbie
 
Registered: Jul 2008
Distribution: Slackware 12.1
Posts: 12

Original Poster
Rep: Reputation: 0
And dmesg on slack 11.
Code:
Linux version 2.4.33.3 (root@tree) (gcc version 3.4.6) #6 Fri Sep 1 04:15:45 CDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003df30000 (usable)
 BIOS-e820: 000000003df30000 - 000000003df40000 (ACPI data)
 BIOS-e820: 000000003df40000 - 000000003dff0000 (ACPI NVS)
 BIOS-e820: 000000003dff0000 - 000000003e000000 (reserved)
 BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
95MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 253744
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 24368 pages.
Kernel command line: BOOT_IMAGE=slackware ro root=302
Initializing CPU#0
Detected 2653.594 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 5295.30 BogoMIPS
Memory: 999816k/1014976k available (1867k kernel code, 14772k reserved, 562k data, 120k init, 97472k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU:     After generic, caps: bfebfbff 20000000 00000000 00000000
CPU:             Common caps: bfebfbff 20000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.66GHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS5595 [1039/0964] at 00:02.0
PCI: Found IRQ 11 for device 00:02.5
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xd0000000, mapped to 0xf880d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c71d:000c
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
PCI: Found IRQ 11 for device 00:02.5
SIS5513: chipset revision 1
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: ST380011A, ATA DISK drive
hdb: TSSTcorpCD-R/RW SH-R522C, ATAPI CD/DVD-ROM drive
hdc: WDC WD102AA, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 20044080 sectors (10263 MB) w/2048KiB Cache, CHS=19885/16/63, UDMA(33)
hdb: attached ide-cdrom driver.
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hda: hda1 hda2 hda3
 hdc: hdc1 hdc2
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   8regs     :  2902.000 MB/sec
   32regs    :  2014.400 MB/sec
   pIII_sse  :  4666.800 MB/sec
   pII_mmx   :  2872.000 MB/sec
   p5_mmx    :  2913.200 MB/sec
raid5: using function: pIII_sse (4666.800 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.8(17/11/2003)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding Swap: 497972k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 909M
agpgart: Unsupported SiS chipset (device id: 0661), you might want to try agp_try_unsupported=1.
agpgart: no supported devices found.
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 00:0b.0
eth0: RealTek RTL8139 at 0xf8b57400, 00:13:d4:62:eb:ac, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
PCI: Found IRQ 5 for device 00:0a.0
PCI: Sharing IRQ 5 with 00:02.7
eth1: RealTek RTL8139 at 0xf8b59c00, 00:02:44:8d:da:cf, IRQ 5
eth1:  Identified 8139 chip type 'RTL-8100B/8139D'
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: Too much work at interrupt, IntrStatus=0x0001.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
ds: no socket drivers loaded!
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
SiS router unknown request: (99)
SiS router unknown request: (99)
ehci_hcd 00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 00:03.3: irq 11, pci mem f8b7f000
usb.c: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 00:03.3
ehci_hcd 00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
PCI: Assigned IRQ 10 for device 00:03.2
usb-ohci.c: USB OHCI at membase 0xf8b87000, IRQ 10
usb-ohci.c: usb-00:03.2, Silicon Integrated Systems [SiS] USB 1.0 Controller (#3)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
SiS pirq: IDE/ACPI/DAQ mapping not implemented: (97)
SiS router unknown request: (97)
SiS pirq: IDE/ACPI/DAQ mapping not implemented: (97)
SiS router unknown request: (97)
usb-ohci.c: USB OHCI at membase 0xf8b89000, IRQ 5
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 3 ports detected
SiS router unknown request: (96)
SiS router unknown request: (96)
usb-ohci.c: USB OHCI at membase 0xf8b8b000, IRQ 5
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Found IRQ 5 for device 00:02.7
PCI: Sharing IRQ 5 with 00:0a.0
intel8x0_measure_ac97_clock: measured 50737 usecs
intel8x0: clocking to 48000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.5
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-uhci.c: $Revision: 1.275 $ time 02:01:41 Sep  1 2006
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
scsi singledevice 0 0 0 0
scsi singledevice 0 0 1 0
scsi singledevice 0 0 2 0
scsi singledevice 0 0 3 0
scsi singledevice 0 0 4 0
scsi singledevice 0 0 5 0
scsi singledevice 0 0 6 0
scsi singledevice 0 0 7 0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (7929 buckets, 63432 max) - 288 bytes per conntrack
 
Old 08-01-2008, 12:39 AM   #4
ErV
Senior Member
 
Registered: Mar 2007
Location: Russia
Distribution: Slackware 12.2
Posts: 1,202
Blog Entries: 3

Rep: Reputation: 62
Quote:
Originally Posted by CesarLG View Post
Now route -n on slack 12.1
Code:
root@darkstar:~# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
Did you configure network on slack 12.1 (looks like you didn't)? This is done either via editing /etc/rc.d/rc.inet1.conf or by calling netconfig as root.
 
Old 08-01-2008, 12:45 AM   #5
CesarLG
LQ Newbie
 
Registered: Jul 2008
Distribution: Slackware 12.1
Posts: 12

Original Poster
Rep: Reputation: 0
I did...
Several times.
I even tried to copy the config files from slack 11. (That's how I got back to re-installing slack 12.1.)
 
Old 08-01-2008, 12:55 AM   #6
bgeddy
Senior Member
 
Registered: Sep 2006
Location: Liverpool - England
Distribution: slackware64 13.37 and -current, Dragonfly BSD
Posts: 1,810

Rep: Reputation: 232Reputation: 232Reputation: 232
Looking at your ifconfig output it appears that the two ethernet ports eth0 and eth1 are getting switched from Slackware 11 to Slackware 12. I.e. eth0 is becoming eth1 and vice versa.

Simply edit /etc/udev/rules.d/70-persistent-net.rules to make sure eth0 is the port with the mac address 00.13.D4.62.EB.AC - the file layout should be self explanatory. Assign eth1 to be consistent as well. Then reboot.

Now your old configs should work or run netconfig again and you should be OK.
 
Old 08-01-2008, 01:21 AM   #7
ErV
Senior Member
 
Registered: Mar 2007
Location: Russia
Distribution: Slackware 12.2
Posts: 1,202
Blog Entries: 3

Rep: Reputation: 62
Quote:
Originally Posted by bgeddy View Post
Then reboot.
"/etc/rc.d/rc.udev restart" and "/etc/rc.d/rc.inet1 restart" should be enough without rebooting.
 
Old 08-01-2008, 01:34 AM   #8
bgeddy
Senior Member
 
Registered: Sep 2006
Location: Liverpool - England
Distribution: slackware64 13.37 and -current, Dragonfly BSD
Posts: 1,810

Rep: Reputation: 232Reputation: 232Reputation: 232
Quote:
"/etc/rc.d/rc.udev restart" and "/etc/rc.d/rc.inet1 restart" should be enough without rebooting.
Yeah - I wasn't sure about udev honoring the rule changes so to be sure I recommended a reboot - when mucking with udev I just reboot. Looking at rc.udev it looks like a restart is good to go.
 
Old 08-01-2008, 10:09 AM   #9
CesarLG
LQ Newbie
 
Registered: Jul 2008
Distribution: Slackware 12.1
Posts: 12

Original Poster
Rep: Reputation: 0
Thanks guys!
It's working.



PS: I had to reboot in order to make it work...
 
  


Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Slack 11 cannot connect with 2.6x kernel The GNUinator Slackware 4 03-20-2007 05:10 PM
Unable to connect to internet in Slack 10 libranikki Slackware 6 04-10-2006 08:10 PM
How to connect to Broadband internet on USB modem in slack 10.2 dark* Slackware 4 01-08-2006 09:30 AM
Slack 10.1 Can't Connect to Internet scc1068 Slackware 3 09-18-2005 01:47 PM
Can't connect to internet with Slack 9.0 abiagi Linux - Networking 4 12-04-2003 11:46 AM

LinuxQuestions.org > Forums > Linux Forums > Linux - Distributions > Slackware

All times are GMT -5. The time now is 08:27 PM.

Contact Us - Advertising Info - Rules - Privacy - LQ Merchandise - Donations - Contributing Member - LQ Sitemap -
Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration