Hi all,

Im using the 2.6.6 kernel, on an Asus A7N8X Delux mobo.
Im also using gkrellm v2.

Problem is, i cant get any info on processor temps, theres
just nothing there at all.

Ive made sure that i2c is enabled in the kernel, and all its
options. Including bach and nvidia support. I then downloaded
lm_sensors latest and following their instructions, i did :

make user
make user_install

Rebooted, and still no sensor info to read.

Anyone know what im doing wrong. Or more to the point
is anyone in this situation and has a working howto??


Cheers,

Ade

run sensors-detect to see if there are any available sensors for your usage... be sure that you have also done mount sys -t sysfs /sys (mount the /sys area) and have done modprobe i2c-dev... it should make sensors-detect work a lot more smoothly

be aware that many sensors have yet to be ported to kernel 2.6

post the output of what happens in sensors-detect here if you are unsure of someting

Here's the output of sensors-detect :

root@merlin:~# sensors-detect

This program will help you determine which I2C/SMBus modules you need to
load to use lm_sensors most effectively. You need to have i2c and
lm_sensors installed before running this program.
Also, you need to be `root', or at least have access to the /dev/i2c-*
files, for most things.
If you have patched your kernel and have some drivers built in, you can
safely answer NO if asked to load some modules. In this case, things may
seem a bit confusing, but they will still work.

It is generally safe and recommended to accept the default answers to all
questions, unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
You do not need any special privileges for this.
Do you want to probe now? (YES/no):
Probing for PCI bus adapters...
Use driver `i2c-nforce2' for device 00:01.1: nVidia Corporation nForce2 SMBus (M
CP)
Probe succesfully concluded.

We will now try to load each adapter module in turn.
Load `i2c-nforce2' (say NO if built into your kernel)? (YES/no):
FATAL: Module i2c_nforce2 not found.
Loading failed... skipping.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
If it is built-in into your kernel, you can safely skip this.
i2c-dev is not loaded. Do you want to load it now? (YES/no):
FATAL: Module i2c_dev not found.
Loading failed, expect problems later on.

We are now going to do the adapter probings. Some adapters may hang halfway
through; we can't really help that. Also, some chips will be double detected;
we choose the one with the highest confidence value in that case.
If you found that the adapter hung after probing a certain address, you can
specify that address to remain unprobed. That often
includes address 0x69 (clock chip).

Some chips are also accessible through the ISA bus. ISA probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan the ISA bus? (YES/no):
Probing for `National Semiconductor LM78'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM78-J'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM79'
Trying address 0x0290... Failed!
Probing for `Winbond W83781D'
Trying address 0x0290... Failed!
Probing for `Winbond W83782D'
Trying address 0x0290... Failed!
Probing for `Winbond W83627HF'
Trying address 0x0290... Failed!
Probing for `Winbond W83697HF'
Trying address 0x0290... Failed!
Probing for `Silicon Integrated Systems SIS5595'
Trying general detect... Failed!
Probing for `VIA Technologies VT82C686 Integrated Sensors'
Trying general detect... Failed!
Probing for `VIA Technologies VT8231 Integrated Sensors'
Trying general detect... Failed!
Probing for `ITE IT8705F / IT8712F / SiS 950'
Trying address 0x0290... Failed!
Probing for `IPMI BMC KCS'
Trying address 0x0ca0... Failed!
Probing for `IPMI BMC SMIC'
Trying address 0x0ca8... Failed!

Some Super I/O chips may also contain sensors. Super I/O probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan for Super I/O sensors? (YES/no):
Probing for `ITE 8702F Super IO Sensors'
Failed!
Probing for `ITE 8705F Super IO Sensors'
Failed!
Probing for `ITE 8712F Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87360 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87363 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87364 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87365 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87366 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87372 Super IO Fan Sensors'
Failed!
Probing for `SMSC 47B27x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M10x/13x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M14x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M15x/192 Super IO Fan Sensors'
Failed!
Probing for `VT1211 Super IO Sensors'
Failed! (0x87)
Probing for `Winbond W83627HF Super IO Sensors'
Failed! (0x87)
Probing for `Winbond W83627THF Super IO Sensors'
Failed! (0x87)
Probing for `Winbond W83637HF Super IO Sensors'
Failed! (0x87)
Probing for `Winbond W83697HF Super IO Sensors'
Failed! (0x87)
Probing for `Winbond W83697UF Super IO PWM'
Failed! (0x87)

Do you want to scan for secondary Super I/O sensors? (YES/no):
Probing for `ITE 8702F Super IO Sensors'
Failed!
Probing for `ITE 8705F Super IO Sensors'
Failed!
Probing for `ITE 8712F Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87360 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87363 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87364 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87365 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87366 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87372 Super IO Fan Sensors'
Failed!
Probing for `SMSC 47B27x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M10x/13x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M14x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M15x/192 Super IO Fan Sensors'
Failed!
Probing for `VT1211 Super IO Sensors'
Failed!
Probing for `Winbond W83627HF Super IO Sensors'
Failed!
Probing for `Winbond W83627THF Super IO Sensors'
Failed!
Probing for `Winbond W83637HF Super IO Sensors'
Failed!
Probing for `Winbond W83697HF Super IO Sensors'
Failed!
Probing for `Winbond W83697UF Super IO PWM'
Failed!

Sorry, no chips were detected.
Either your sensors are not supported, or they are
connected to an I2C bus adapter that we do not support.
See doc/FAQ, doc/lm_sensors-FAQ.html, or
http://www2.lm-sensors.nu/~lm78/cvs/...nsors-FAQ.html
(FAQ #4.24.3) for further information.
If you find out what chips are on your board, see
http://secure.netroedge.com/~lm78/newdrivers.html for driver status.
root@merlin:~#

As you can see i don't seem to have the modules there to load. I only did a make user and make user_instaill for lm_sensors. Not sure what this does but it's what the README file said to do for a 2.6 kernel.

I've enabled ic2 as built into the kernel as follows :

I2C Support
I2C Device interface
I2C Algorithms > I2C bit-banging interfaces > I2C PCF 8584 interfaces
I2C Hardware Bus support > NVIDIA Nforce2 > AMD 8111 > AMD 756/766
Hardware sensor chip support > ASUS ASB100 Bach >
Other I2C Chip support > EEPROM reader > Phillips PCF8574 and PCF8574A > Phillips PCF8591

I've not seen anything to do with lm_sensors so hence i did the user space install (Whatever that means, explanation would be good).

As a last ditch attempt, i looked at another of my linux boxes at work, which also runs gkrellm 2 and this one picks up the sensor data. Different board, it's an EPOX. I've looked into the kernel i compiled there, and there's NO ic2 support built in???????? I don't run any modules on that one either, so i'm totally lost now.

Hope you can help, this is becoming a quest !!!

cheers,

Ade

Edit : Oh yeah , i tried the mount command, and when i key it in as follows :

mount sys -t sysfs /sys

it gives me an error , and a man page to read. Did i key it in incorrectly??? Should i have modified it ?? Never had a need to do this before, so again, i'm stumped as to what it does.

OK forget that...... I've now got sensors working, kind of !!!

If i now type sensors i get this :

root@merlin:~# sensors
eeprom-i2c-0-51
Adapter: SMBus nForce2 adapter at 5000
Memory type: DDR SDRAM DIMM
Memory size (MB): 512

eeprom-i2c-0-50
Adapter: SMBus nForce2 adapter at 5000
Memory type: DDR SDRAM DIMM
Memory size (MB): 512

asb100-i2c-1-2d
Adapter: SMBus nForce2 adapter at 5500
VCore 1: +1.71 V (min = +1.31 V, max = +1.97 V)
+3.3V: +3.31 V (min = +2.96 V, max = +3.63 V)
+5V: +4.97 V (min = +4.49 V, max = +5.51 V)
+12V: +11.55 V (min = +9.55 V, max = +14.41 V)
-12V (reserved):
-12.07 V (min = -0.00 V, max = -0.00 V)
-5V (reserved):
-5.06 V (min = -0.00 V, max = -0.00 V)
CPU Fan: 4720 RPM (min = 21093 RPM, div = 2)
Chassis Fan:
0 RPM (min = -1 RPM, div = 2)
Power Fan: 0 RPM (min = -1 RPM, div = 2)
M/B Temp: +54 C (high = +80 C, hyst = +75 C)
CPU Temp (Intel):
+37 C (high = +80 C, hyst = +75 C)
Power Temp:
+125 C (high = +80 C, hyst = +75 C)
CPU Temp (AMD):
+25 C (high = +80 C, hyst = +75 C)
vid: +1.650 V
alarms:

root@merlin:~#


Hoo fricken ray !!!!

However i still have a couple of questions

a) what does the make user actually do????

b) what does the mount sys command do??? do i need to do this at boot time????? if so i'm asuming i do it in fstab how?

c) Looking at my above data, what temp is my processor running at???? For the life of me i can't tell.

d) Why the hell is gkrellm still NOT picking up sensor data (i've restarted it),

I love linux, but i don't think it loves me sometimes !

okay, glad to see you've got it working

first, for kernel, next time it is a good idea to make everything in the i2c section a module; don't pick and choose and it won't enlarge your kernel anyway

the kernel doesn't contain anything that states "lmsensors"; everything is in the i2c section since lmsensors for kernel 2.6 has work done directly into the kernel tree, whereas 2.4 kernels need the outside modules

the make user install installs the user-space tools, like sensors-detect, sensors, isa-dump, fancontrol, pwmconfig, etc... for 2.4 kernels, you would have had to do make all, which would not only build the user-space tools, but the sensors modules as well since the native one in 2.4 kernels is broken and out of date

first, i was mistaken (a bit) on the sys mount command.... oops
first, make sure you actually have a /sys dir by doing mkdir /sys
then do mount sysfs -t sysfs /sys
you should add an fstab entry like so: (yes, you need to have this loaded at boot-time)
syfs /sys sysfs defaults 0 0

sysfs is a virtual filesystem (like proc) that gives information about what the kernel knows about various hardware and chipsets in your computer; if you browse it, you will see that it changes when you plugin something to usb, and contains a lot of low-level information (such as about block devices)... this is intended to allow programs communicate with hardware more easily and is essential with the new udev system coming about (to replace devfs)

as for which one is your cpu temp, i don't know; for me, i ran a blowdryer across my cpu to see which was affected the most and also just did some long compiling to see which temperature rose the most; that would be your cpu temp (i recommend just compiling MPlayer and watch the temperatures with sensors)
my guess is that 37 degrees is the cpu temp, it seems realistic (25 seems too low)

also, did you do sensors -s before looking at this output? this command will set some configuration options that can often affect what the sensors output is; the sensors-detect recommends doing sensors -s

as for why gkrellm isn't displaying anything, make sure you have sysfs mounted; then i need to know what the output of lsmod gives (i believe gkrellm requires i2c-dev being loaded);
sometimes it is hard to see that gkrellm is detecting the sensors... if there is an arrow next to fans, voltages, and temps, just open those arrows (it took me a while to notice them)

Ok, thanks for all that, its helped....

I did indeed run sensors -s

I´ll keep going, itś not beating me that easily..

The output of lsmod only lists my nvidia driver, as i said, ive not used modules
since the 2.6 kernels first came out. I do remember somthing on the IC2 homepage
that refered to building IC2 as modules for best effect, i´ll maybee do a recompile later.

Im pretty sure that the Asus A7n8x uses the bach chipset. And it seems ok, as i get
output from sensors, as youve seen.

Don´t know about gkrellm at the moment. Like i said, my other box works ok with cpu
temps, and its configured more or less the same, no modules and no IC2 in the kernel.
The only difference is the epox motherboard. So again itś down to why the hell is it working on one box and not on another, gkrellm obviously isńt using lmsensors, IC2 or the mount sys.
It cant be, as this is the first time ive ever had to use it. And none of it is enabled on my other box.... WEIRD !!!!

Ade

does your other box run a 2.6 kernel? are the drivers for that kernel built as modules or are they built into the kernel?

so you have sysfs mounted.... and gkrellm still won't show anything? gkrellm queries (afaik) sensors and/or the proc entries in /proc/sys/dev/sensors/chipname

make sure you have proc mounted (it should be by default)

what is the output of lsmod?

you may just want to go ahead and recompile your kernel; it shouldn't be hard if you still have your config; just enable everyting in i2c as modules

rerun sensors-detect so it can load the necessary modules

Yes the other box is also 2.6.6, and no i´ve not compiled ic2 into the kernel on that one,
in fact, ive not even set it as a module... I´d never heard of it untill a couple of days ago, so it remained unchecked. sysfs is NOT mounted on that box either, as again, i´ve only just heard of it.

This is what´s confusing me !!!!!

Proc is mounted by default on both boxes.

Output of lsmod is as follows :

root@merlin:~# lsmod
Module Size Used by
nvidia 2076520 12
root@merlin:~#

as i mentioned in last post, only nvidia module present.

Ade

oops, sorry, didn't see that in your last post...

but now i'm confused.... how is sensors working without any modules? zounds! something is amiss! sensors can't query anything without the i2c modules, what is going on?

btw, sysfs is compiled into the kernel by default.... if fact, there isn't a way to disable that feature, so it is present in every 2.6 kernel

do you have any idea how you got sensors to give output? what steps did you take?

i am going to recommend a kernel recompile at this point; enable everything as modules in i2c, but do not build the i2c debugging

Following that thread, does not helped me getting sensors to work. Here's what I've done, let's hope somebody can point me to the right direction.
I'm running FC2 with custom kernel 2.6.6 with all ic2 modules. I have also a /sys partition, so first i did "sensors-detect" with this result:

This program will help you determine which I2C/SMBus modules you need to
load to use lm_sensors most effectively. You need to have i2c and
lm_sensors installed before running this program.
Also, you need to be `root', or at least have access to the /dev/i2c-*
files, for most things.
If you have patched your kernel and have some drivers built in, you can
safely answer NO if asked to load some modules. In this case, things may
seem a bit confusing, but they will still work.

It is generally safe and recommended to accept the default answers to all
questions, unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
You do not need any special privileges for this.
Do you want to probe now? (YES/no): yes
Probing for PCI bus adapters...
Use driver `i2c-sis96x' for device 00:02.1: Silicon Integrated Systems SMBus Controller
Probe succesfully concluded.

We will now try to load each adapter module in turn.
Load `i2c-sis96x' (say NO if built into your kernel)? (YES/no): yes
Module loaded succesfully.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
If it is built-in into your kernel, you can safely skip this.
i2c-dev is not loaded. Do you want to load it now? (YES/no): yes
Module loaded succesfully.

We are now going to do the adapter probings. Some adapters may hang halfway
through; we can't really help that. Also, some chips will be double detected;
we choose the one with the highest confidence value in that case.
If you found that the adapter hung after probing a certain address, you can
specify that address to remain unprobed. That often
includes address 0x69 (clock chip).

Next adapter: SiS96x SMBus adapter at 0xe600 (Algorithm unavailable)
Do you want to scan it? (YES/no/selectively): yes
Client found at address 0x08
Client found at address 0x10
Client found at address 0x2d
Probing for `Myson MTP008'... Failed!
Probing for `National Semiconductor LM78'... Failed!
Probing for `National Semiconductor LM78-J'... Failed!
Probing for `National Semiconductor LM79'... Failed!
Probing for `National Semiconductor LM80'... Failed!
Probing for `National Semiconductor LM85'... Failed!
Probing for `Analog Devices ADM1027 or ADT7463'... Failed!
Probing for `SMSC EMC6D100 and EMC6D101'... Failed!
Probing for `National Semiconductor LM87'... Failed!
Probing for `Winbond W83781D'... Failed!
Probing for `Winbond W83782D'... Failed!
Probing for `Winbond W83783S'... Failed!
Probing for `Winbond W83791D'... Failed!Probing for `Winbond W83627HF'... Failed!
Probing for `Asus AS99127F (rev.1)'... Failed!
Probing for `Asus AS99127F (rev.2)'... Failed!
Probing for `Asus ASB100 Bach'... Success!
(confidence 8, driver `asb100'), other addresses: 0x48 0x49
Probing for `Winbond W83L784R/AR'... Failed!
Probing for `Winbond W83L785R'... Failed!
Probing for `Genesys Logic GL518SM Revision 0x00'... Failed!
Probing for `Genesys Logic GL518SM Revision 0x80'... Failed!
Probing for `Genesys Logic GL520SM'... Failed!
Probing for `Genesys Logic GL525SM'... Failed!
Probing for `Analog Devices ADM9240'... Failed!
Probing for `Dallas Semiconductor DS1780'... Failed!
Probing for `National Semiconductor LM81'... Failed!
Probing for `Analog Devices ADM1026'... Failed!
Probing for `Analog Devices ADM1025'... Failed!
Probing for `Philips NE1619'... Failed!
Probing for `Analog Devices ADM1024'... Failed!
Probing for `Analog Devices ADM1029'... Failed!
Probing for `Analog Devices ADM1030'... Failed!
Probing for `Analog Devices ADM1031'... Failed!
Probing for `Analog Devices ADM1022'... Failed!
Probing for `Texas Instruments THMC50'... Failed!
Probing for `ITE IT8705F / IT8712F / SiS 950'... Failed!
Probing for `ALi M5879'... Failed!
Client found at address 0x30
Client found at address 0x48
Probing for `National Semiconductor LM75'... Failed!
Probing for `Dallas Semiconductor DS1621'... Failed!
Probing for `Maxim MAX6650/MAX6651'... Failed!
Client found at address 0x49
Probing for `National Semiconductor LM75'... Success!
(confidence 4, driver `lm75')
Probing for `Dallas Semiconductor DS1621'... Failed!
Client found at address 0x50
Probing for `SPD EEPROM'... Success!
(confidence 8, driver `eeprom')
Probing for `DDC monitor'... Failed!
Probing for `Maxim MAX6900'... Failed!

Some chips are also accessible through the ISA bus. ISA probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan the ISA bus? (YES/no): yes
Probing for `National Semiconductor LM78'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM78-J'Probing for `Winbond W83782D'
Trying address 0x0290... Failed!
Probing for `Winbond W83627HF'
Trying address 0x0290... Failed!
Probing for `Winbond W83697HF'
Trying address 0x0290... Failed!
Probing for `Silicon Integrated Systems SIS5595'
Trying general detect... Failed!
Probing for `VIA Technologies VT82C686 Integrated Sensors'
Trying general detect... Failed!
Probing for `VIA Technologies VT8231 Integrated Sensors'
Trying general detect... Failed!
Probing for `ITE IT8705F / IT8712F / SiS 950'
Trying address 0x0290... Failed!
Probing for `IPMI BMC KCS'
Trying address 0x0ca0... Failed!
Probing for `IPMI BMC SMIC'
Trying address 0x0ca8... Failed!

Some Super I/O chips may also contain sensors. Super I/O probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan for Super I/O sensors? (YES/no): yes
Probing for `ITE 8702F Super IO Sensors'
Failed!
Probing for `ITE 8705F Super IO Sensors'
Failed!
Probing for `ITE 8712F Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87360 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87363 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87364 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87365 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87366 Super IO Sensors'
Failed! Failed! (0x68)
Probing for `Winbond W83627HF Super IO Sensors'
Failed! (0x68)
Probing for `Winbond W83627THF Super IO Sensors'
Failed! (0x68)
Probing for `Winbond W83637HF Super IO Sensors'
Failed! (0x68)
Probing for `Winbond W83697HF Super IO Sensors'
Failed! (0x68)
Probing for `Winbond W83697UF Super IO PWM'
Success... but not activated

Do you want to scan for secondary Super I/O sensors? (YES/no): yes
Probing for `ITE 8702F Super IO Sensors'
Failed!
Probing for `ITE 8705F Super IO Sensors'
Failed!
Probing for `ITE 8712F Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87360 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87363 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87364 Super IO Fan Sensors'
Failed!
Probing for `Nat. Semi. PC87365 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87366 Super IO Sensors'
Failed!
Probing for `Nat. Semi. PC87372 Super IO Fan Sensors'
Failed!
Probing for `SMSC 47B27x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M10x/13x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M14x Super IO Fan Sensors'
Failed!
Probing for `SMSC 47M15x/192 Super IO Fan Sensors'
Failed!
Probing for `VT1211 Super IO Sensors'
Failed!
Probing for `Winbond W83627HF Super IO Sensors'
Failed!
Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `asb100' (should be inserted):
Detects correctly:
* Bus `SiS96x SMBus adapter at 0xe600' (Algorithm unavailable)
Busdriver `i2c-sis96x', I2C address 0x2d (and 0x48 0x49)
Chip `Asus ASB100 Bach' (confidence: 8)

Driver `lm75' (may not be inserted):
Misdetects:
* Bus `SiS96x SMBus adapter at 0xe600' (Algorithm unavailable)
Busdriver `i2c-sis96x', I2C address 0x49
Chip `National Semiconductor LM75' (confidence: 4)

Driver `eeprom' (should be inserted):
Detects correctly:
* Bus `SiS96x SMBus adapter at 0xe600' (Algorithm unavailable)
Busdriver `i2c-sis96x', I2C address 0x50
Chip `SPD EEPROM' (confidence: 8)


I will now generate the commands needed to load the I2C modules.
Sometimes, a chip is available both through the ISA bus and an I2C bus.
ISA bus access is faster, but you need to load an additional driver module
for it. If you have the choice, do you want to use the ISA bus or the
I2C/SMBus (ISA/smbus)? smbus

To make the sensors modules behave correctly, add these lines to
/etc/modules.conf:

#----cut here----
# I2C module options
alias char-major-89 i2c-dev
#----cut here----

To load everything that is needed, add this to some /etc/rc* file:

#----cut here----
# I2C adapter drivers
modprobe i2c-sis96x
# I2C chip drivers
modprobe asb100
modprobe eeprom
# sleep 2 # optional
/usr/bin/sensors -s # recommended
#----cut here----
Do you want to generate /etc/sysconfig/lm_sensors? (YES/no): yes
Copy prog/init/lm_sensors.init to /etc/rc.d/init.d/lm_sensors
for initialization at boot time.

After that, i did:

[root][/usr/src/linux-2.6.6]$ sensors
No sensors found!


And i got no sensors detected!!
Thnx in advance for the help

from that list it gives you at the end, modprobe all those modules

make sure i2c-dev and i2c-isa are also loaded

then run sensors -s, and sensors should give some info

Thanx!!! It works ^__^

Hehehe i told you it was flipping my head out... My other box does NOT have i2c installed at all. All i did was make a custom kernel, selecting my usual setup, ie, processor type, board chipsets, nic drivers, etc ... And then fired up gkrellm2 and selected options > Sensors, and added the cpu temps to the monitor. LOL I know it's weird, that's why i said earlier that gkrellm can't be using ic2, it's not running on the other box, nor is lm_sensors. I only started to look into all this after my second box failed to show me any temps... I google'd for linux sensor temp and up popped lm_sensors. The rest you know. If it helps here's the .config file from my other box with working sensor data :

See next post

#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_STANDALONE=y

#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=15
CONFIG_HOTPLUG=y
# CONFIG_IKCONFIG is not set
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODVERSIONS is not set
CONFIG_KMOD=y
CONFIG_STOP_MACHINE=y

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
# CONFIG_HPET_TIMER is not set
# CONFIG_HPET_EMULATE_RTC is not set
CONFIG_SMP=y
CONFIG_NR_CPUS=8
CONFIG_PREEMPT=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
# CONFIG_X86_MCE_P4THERMAL is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
CONFIG_MICROCODE=y
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_EFI is not set
CONFIG_IRQBALANCE=y
CONFIG_HAVE_DEC_LOCK=y
# CONFIG_REGPARM is not set

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_SOFTWARE_SUSPEND=y
# CONFIG_PM_DISK is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_ASUS=y
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_X86_PM_TIMER=y

#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
# CONFIG_APM_DO_ENABLE is not set
# CONFIG_APM_CPU_IDLE is not set
# CONFIG_APM_DISPLAY_BLANK is not set
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_PCI_USE_VECTOR is not set
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
# CONFIG_EISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set

#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
CONFIG_PCMCIA_PROBE=y

#
# PCI Hotplug Support
#
CONFIG_HOTPLUG_PCI=y
# CONFIG_HOTPLUG_PCI_FAKE is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
CONFIG_HOTPLUG_PCI_ACPI=y
# CONFIG_HOTPLUG_PCI_CPCI is not set
CONFIG_HOTPLUG_PCI_PCIE=y
# CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE is not set
# CONFIG_HOTPLUG_PCI_SHPC is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y

#
# Device Drivers
#

#
# Generic Driver Options
#
# CONFIG_FW_LOADER is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_OTHER is not set
# CONFIG_PARPORT_1284 is not set

#
# Plug and Play support
#
CONFIG_PNP=y
# CONFIG_PNP_DEBUG is not set

#
# Protocols
#
CONFIG_ISAPNP=y
CONFIG_PNPBIOS=y
CONFIG_PNPBIOS_PROC_FS=y

#
# Block devices
#
CONFIG_BLK_DEV_FD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_CARMEL is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_LBD=y

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_IDEDISK_STROKE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
CONFIG_BLK_DEV_IDESCSI=y
# CONFIG_IDE_TASK_IOCTL is not set
CONFIG_IDE_TASKFILE_IO=y

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
# CONFIG_BLK_DEV_CMD640_ENHANCED is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
CONFIG_BLK_DEV_AMD74XX=y
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_REPORT_LUNS=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_MEGARAID is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_SVW is not set
CONFIG_SCSI_ATA_PIIX=y
# CONFIG_SCSI_SATA_PROMISE is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIS is not set
# CONFIG_SCSI_SATA_VIA is not set
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set

continued ....

#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set

#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_DM=y
# CONFIG_DM_CRYPT is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=y

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
# CONFIG_IEEE1394_EXTRA_CONFIG_ROMS is not set

#
# Device Drivers
#

#
# Texas Instruments PCILynx requires I2C
#
CONFIG_IEEE1394_OHCI1394=y

#
# Protocol Drivers
#
# CONFIG_IEEE1394_VIDEO1394 is not set
# CONFIG_IEEE1394_SBP2 is not set
# CONFIG_IEEE1394_ETH1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
CONFIG_IEEE1394_RAWIO=y
# CONFIG_IEEE1394_CMP is not set

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Networking support
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set

#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=y
# CONFIG_IP_NF_FTP is not set
# CONFIG_IP_NF_IRC is not set
# CONFIG_IP_NF_TFTP is not set
# CONFIG_IP_NF_AMANDA is not set
CONFIG_IP_NF_QUEUE=y
CONFIG_IP_NF_IPTABLES=y
CONFIG_IP_NF_MATCH_LIMIT=y
CONFIG_IP_NF_MATCH_IPRANGE=y
CONFIG_IP_NF_MATCH_MAC=y
CONFIG_IP_NF_MATCH_PKTTYPE=y
CONFIG_IP_NF_MATCH_MARK=y
CONFIG_IP_NF_MATCH_MULTIPORT=y
CONFIG_IP_NF_MATCH_TOS=y
CONFIG_IP_NF_MATCH_RECENT=y
CONFIG_IP_NF_MATCH_ECN=y
CONFIG_IP_NF_MATCH_DSCP=y
CONFIG_IP_NF_MATCH_AH_ESP=y
CONFIG_IP_NF_MATCH_LENGTH=y
CONFIG_IP_NF_MATCH_TTL=y
CONFIG_IP_NF_MATCH_TCPMSS=y
CONFIG_IP_NF_MATCH_HELPER=y
CONFIG_IP_NF_MATCH_STATE=y
CONFIG_IP_NF_MATCH_CONNTRACK=y
CONFIG_IP_NF_MATCH_OWNER=y
CONFIG_IP_NF_FILTER=y
CONFIG_IP_NF_TARGET_REJECT=y
CONFIG_IP_NF_NAT=y
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=y
CONFIG_IP_NF_TARGET_REDIRECT=y
CONFIG_IP_NF_TARGET_NETMAP=y
CONFIG_IP_NF_TARGET_SAME=y
# CONFIG_IP_NF_NAT_LOCAL is not set
# CONFIG_IP_NF_NAT_SNMP_BASIC is not set
CONFIG_IP_NF_MANGLE=y
CONFIG_IP_NF_TARGET_TOS=y
CONFIG_IP_NF_TARGET_ECN=y
CONFIG_IP_NF_TARGET_DSCP=y
CONFIG_IP_NF_TARGET_MARK=y
CONFIG_IP_NF_TARGET_CLASSIFY=y
CONFIG_IP_NF_TARGET_LOG=y
CONFIG_IP_NF_TARGET_ULOG=y
CONFIG_IP_NF_TARGET_TCPMSS=y
CONFIG_IP_NF_ARPTABLES=y
CONFIG_IP_NF_ARPFILTER=y
CONFIG_IP_NF_ARP_MANGLE=y
# CONFIG_IP_NF_RAW is not set

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_NET_SB1000 is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set

#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_CS89x0 is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
CONFIG_NATSEMI=y
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
# CONFIG_8139TOO is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_NET_POCKET is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set

#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_SERIAL=y
# CONFIG_MOUSE_INPORT is not set
CONFIG_MOUSE_LOGIBM=y
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_ACPI is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=y
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
# CONFIG_QIC02_TAPE is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set

#
# Ftape, the floppy tape device driver
#
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_INTEL_MCH is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
CONFIG_AGP_VIA=y
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set

#
# I2C support
#
# CONFIG_I2C is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set

#
# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
CONFIG_FB_VIRTUAL=y

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_MDA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_PCI_CONSOLE=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y

#
# Sound
#
# CONFIG_SOUND is not set

#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=y
# CONFIG_USB_EHCI_SPLIT_ISO is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_UHCI_HCD=y

#
# USB Device Class drivers
#
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set

#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set

#
# Video4Linux support is needed for USB Multimedia device support
#

#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set

#
# USB port drivers
#
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_TEST is not set

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_JFS_FS=y
# CONFIG_JFS_POSIX_ACL is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
# CONFIG_ZISOFS is not set
CONFIG_UDF_FS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
CONFIG_NTFS_RW=y

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=y
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=y
CONFIG_EXPORTFS=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
# CONFIG_NLS_CODEPAGE_850 is not set
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
# CONFIG_NLS_ISO8859_15 is not set
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set

#
# Profiling support
#
CONFIG_PROFILING=y
CONFIG_OPROFILE=y

#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_EARLY_PRINTK=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_FRAME_POINTER is not set
# CONFIG_4KSTACKS is not set
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y

#
# Security options
#
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
# CONFIG_CRYPTO is not set

#
# Library routines
#
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_X86_STD_RESOURCES=y
CONFIG_PC=y

END