I set this controller into PCI slot and Connect SATA HDD and I cannot mount device.
Code:
root@htb-workshop:/home/hatebreeder# lspci
00:00.0 Host bridge: Intel Corporation 82810 DC-100 GMCH [Graphics Memory Controller Hub] (rev 03)
00:01.0 VGA compatible controller: Intel Corporation 82810 DC-100 CGC [Chipset Graphics Controller] (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02)
00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801AA IDE (rev 02)
00:1f.2 USB Controller: Intel Corporation 82801AA USB (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio (rev 02)
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:01.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
Code:
root@htb-workshop:/home/hatebreeder# dmesg|grep ACPI
BIOS-e820: 000000000fef0000 - 000000000fef3000 (ACPI NVS)
BIOS-e820: 000000000fef3000 - 000000000ff00000 (ACPI data)
ACPI: RSDP (v000 IntelR ) @ 0x000f6da0
ACPI: RSDT (v001 AWARD AWRDACPI 0x30302e31 AWRD 0x00000000) @ 0x0fef3000
ACPI: FADT (v001 AWARD AWRDACPI 0x30302e31 AWRD 0x00000000) @ 0x0fef3040
ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: setting ELCR to 0200 (from 0800)
ACPI: bus type pci registered
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 4000-407f claimed by ICH4 ACPI/GPIO/TCO
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
PCI: Using ACPI for IRQ routing
apm: overridden by ACPI.
ACPI wakeup devices:
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
I am using slackware current (kernel 2.6.17.8).
