Hi

I have been trying to scan the channels using
Hauppauge wintv nova-s-plus card (conexant Chipset no
cx23883-39) on RHEL im getting the output as "No such
device or address" what is this?Could you please help
me with this? I have provided the version info below
and my findings below.

Thanks in advance...
=======================================
Im using

RHEL 4
Kernel version 2.6.9
Hauppauge wintv nova-s-plus card (Chipset no
cx23883-39)

after inserting the information about the card to
cx88-cards.c

when i run xawtv –hwscan, I see the following output

This is xawtv -3.95, running on Linux | i686
(2.6.9-prep)

looking for available devices port 69-69

type : X video, image scaler.

name : intel(R) video overlay

driver = /dev/video0 ; device = Hauppauge Nova-s-Plus
DVB-S

when i'm tring to scan the following FATAL message is
came
using '/dev/dvb/adapter0/frontend0' and
'/dev/dvb/adapter0/demux0'
main:1882: FATAL: failed to open
'/dev/dvb/adapter0/frontend0': 6 No such device or
address

The following is the output of dmesg:

Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.4 loaded
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 21 (level,
low) -> IRQ 217
cx8800[0]: found at 0000:01:0a.0, rev: 5, irq: 217,
latency: 64, mmio: 0xfa000000
cx8800[0]: subsystem: 0070:9202, board: Hauppauge
Nova-S-Plus DVB-S [card=37,autodetected]
cx8800[0]: i2c register ok
cx8800[0]: registered device video0 [v4l2]
cx8800[0]: registered device vbi0
cx8800[0]: cx88: tvaudio thread started
IA-32 Microcode Update Driver v1.14 unregistered
cx8800[0]: AUD_STATUS: 0x36 [mono/pilot c1]
ctl=BTSC_FORCE_MONO
cx8800[0]: AUD_STATUS: 0x36 [mono/pilot c1]
ctl=BTSC_FORCE_MONO
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
e100: eth0: e100_watchdog: link up, 100Mbps,
full-duplex
cx8800[0]: AUD_STATUS: 0x36 [mono/pilot c1]
ctl=BTSC_FORCE_MONO
eth0: no IPv6 routers present
mdrbdr: disagrees about version of symbol
struct_module
cx8800[0]: AUD_STATUS: 0x36 [mono/pilot c1]
ctl=BTSC_FORCE_MONO
lp: driver loaded but no devices found
cx8800[0]: AUD_STATUS: 0x36 [mono/pilot c1]
ctl=BTSC_FORCE_MONO
tveeprom: Encountered bad packet header [17]. Corrupt
or not a Hauppauge eeprom.
cx8800[0]: i2c attach [client=tveeprom]
ivtv: ==================== START INIT IVTV
====================
ivtv: version 0.4.0 (tagged release) loading
ivtv: Linux version: 2.6.9-prep SMP 686 REGPARM
4KSTACKS gcc-3.4
ivtv: In case of problems please include the debug
info
ivtv: between the START INIT IVTV and END INIT IVTV
lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: ==================== END INIT IVTV
===================


The following is the output of lsmod | grep cx88:

cx8800 47388 0
cx88xx 29188 1 cx8800
video_buf 24836 3 saa7146_vv,cx8800,cx88xx
i2c_algo_bit 12808 2 ivtv,cx8800
v4l1_compat 16260 2 saa7146_vv,cx8800
v4l2_common 10240 2 saa7146_vv,cx8800
btcx_risc 8840 2 cx8800,cx88xx
videodev 13952 3 saa7146_vv,ivtv,cx8800
i2c_core 26240 30
dvb_usb_dibusb_mb,dvb_usb,b2c2_flexcop,dvb_ttusb_budget,budget_av,budget_ci,budget,budget_core,
dvb_ttpci,ttpci_eeprom,nxt2002,stv0297,mt352,mt312,cx22702,cx24110,tda8083,l64781,dib3000_common,
tda10021,tda1004x,ves1820,stv0299,cx22700,sp8870,ves1x93,tveeprom,cx8800,cx88xx,i2c_algo_bit