# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").

# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.

# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.

# =============================================================================

# Config information for eth0:
IPADDR[0]=""
NETMASK[0]=""
USE_DHCP[0]="yes"
DHCP_HOSTNAME[0]=""

# Config information for eth1:
IPADDR[1]=""
NETMASK[1]=""
USE_DHCP[1]=""
DHCP_HOSTNAME[1]=""

# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""

# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""

# Default gateway IP address:
GATEWAY=""

# Change this to "yes" for debugging output to stdout.  Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"

## Example config information for wlan0.  Uncomment the lines you need and fill
## in your info.  (You may not need all of these for your wireless network)
IFNAME[4]="wlan0"
IPADDR[4]=""
NETMASK[4]=""
USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]=""
#DHCP_TIMEOUT[4]=1
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
WLAN_ESSID[4]=xxxxxxxxx
WLAN_MODE[4]=Managed
#WLAN_RATE[4]="54M auto"
WLAN_CHANNEL[4]="6"
#WLAN_KEY[4]="s:xxxxx"
WLAN_IWPRIV[4]="set AuthMode=WPA2PSK | set EncrypType=AES | set WPAPSK="x"
WLAN_WPA[4]="wpa_supplicant"
WLAN_WPADRIVER[4]="wext"
WLAN_WPAWAIT[4]=30
## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0"              # Use a different interface name nstead of
                                # the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89"  # Overrule the card's hardware MAC address
#MTU[4]=""                      # The default MTU is 1500, but you might need
                                # 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes"       # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes"          # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes"           # If you don't want the DHCP server to change
                                # your default gateway
#DHCP_IPADDR[4]=""              # Request a specific IP address from the DHCP
                                # server
#WLAN_ESSID[4]=DARKSTAR         # Here, you can override _any_ parameter
                                # defined in rc.wireless.conf, by prepending
                                # 'WLAN_' to the parameter's name. Useful for
                                # those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey"
                                # Some drivers require a private ioctl to be
                                # set through the iwpriv command. If more than
                                # one is required, you can place them in the
                                # IWPRIV parameter (separated with the pipe (|)
                                # character, see the example).

# See /usr/doc/wpa_supplicant-0.5.7/wpa_supplicant.conf.sample
# for many more options that you can use in this file.

# This line enables the use of wpa_cli which is used by rc.wireless
# if possible (to check for successful association)
ctrl_interface=/var/run/wpa_supplicant
# By default, only root (group 0) may use wpa_cli
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1

# WPA protected network, supply your own ESSID and WPAPSK here:
network={
  scan_ssid=0
  ssid="nwid"
  proto=WPA WPA2
  key_mgmt=WPA-PSK
  pairwise=CCMP TKIP
  group=CCMP TKIP WEP104 WEP40
  psk=nwkey
}

# Plaintext connection (no WPA, no IEEE 802.1X),
# nice for hotel/airport types of WiFi network.
# You'll need a recent version of wireless-tools for this!
#network={
#  ssid="any"
#  key_mgmt=NONE
#  priority=2
#}