Linux frozen on new computer

miros84 · 01-21-2013, 09:08 AM

Hi,

Several days ago I buy a new computer and installed Debian wheezy.
First days everthing was Ok, but now it froze several time.
I tried Contr + Alt + 1,2,3,4,5,6 but nothing happend.

I didnot install new almost new programs. Only ssh, virtualbox and rsync.

Now I booted Linux Mint to post this message and with Live CD Linux-Mint it works good. Any idea how can I check and where can I see for errors?

pramodbisht · 01-21-2013, 09:23 AM

you may check the logs in /var/log/messages after booting from live cd and get idea if any h/w issue..
or any s/w clash..

miros84 · 01-21-2013, 10:55 AM

I check that log but nothig important.
When Linux crashed I just opened Chromium.

After reboot I open Chromium again and I saw that adobe flash player was blocked because out of date. Colud be this the problem? What can I do when computer is frozen? Some keys combination?

m1rr0rm3 · 01-21-2013, 07:20 PM

Generally the only reason for a freeze or a lock up on a computer is due to memory usage.

Check to see how much ram is on your computer. Sometimes people put mismatched ram sticks on a computer (i.e 512k and 1024k) when you should be using matched pairs for best performance.

having mismatched pairs causes the computer to default to the lower of the two (i.e. 512k)

check your hardware requirements

Chris

miros84 · 01-22-2013, 01:38 AM

I know that, but that is not he problem. Computer has only 1 module of 4GB and it uses less then 1GB.

There is other reason, but I dont know how to check it. Other ideas?

H_TeXMeX_H · 01-22-2013, 03:16 AM

Run memtest86+ and see if it finds any errors.

miros84 · 01-22-2013, 03:20 AM

Quote:

Originally Posted by H_TeXMeX_H

Run memtest86+ and see if it finds any errors.

It is not hardware problem. Memtest and Hdd test are OK. No problems.

Live CD run OK, and now Debian I installed also run well. I think is some confilct.
How can I change to terminal is it is frozen again?

H_TeXMeX_H · 01-22-2013, 03:29 AM

You can try Alt-SysRq-REISUB:
http://en.wikipedia.org/wiki/Reisub
It should work if it is enabled in the kernel and may cause more things to appear in the logs. Also check /var/log/syslog.

If there is still nothing then post the output of 'dmesg'.

miros84 · 01-22-2013, 03:46 AM

Here is the dmesg

Code:

[    0.302203] pci 0000:00:02.0:   bridge window [io  0xe000-0xefff]
[    0.302206] pci 0000:00:02.0:   bridge window [mem 0xfd000000-0xfe0fffff]
[    0.302208] pci 0000:00:02.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.302211] pci 0000:00:09.0: PCI bridge to [bus 02-02]
[    0.302213] pci 0000:00:09.0:   bridge window [mem 0xfe100000-0xfe1fffff]
[    0.302216] pci 0000:00:14.4: PCI bridge to [bus 03-03]
[    0.302226] pci 0000:00:15.0: PCI bridge to [bus 04-04]
[    0.302233] pci 0000:00:15.3: PCI bridge to [bus 05-05]
[    0.302236] pci 0000:00:15.3:   bridge window [io  0xd000-0xdfff]
[    0.302241] pci 0000:00:15.3:   bridge window [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.302256] pci 0000:00:02.0: setting latency timer to 64
[    0.302262] pci 0000:00:09.0: setting latency timer to 64
[    0.302273] pci 0000:00:15.0: setting latency timer to 64
[    0.302279] pci 0000:00:15.3: setting latency timer to 64
[    0.302282] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.302283] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.302285] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.302286] pci_bus 0000:00: resource 7 [mem 0x000c8000-0x000dffff]
[    0.302288] pci_bus 0000:00: resource 8 [mem 0xc0000000-0xffffffff]
[    0.302289] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.302291] pci_bus 0000:01: resource 1 [mem 0xfd000000-0xfe0fffff]
[    0.302292] pci_bus 0000:01: resource 2 [mem 0xc0000000-0xd1ffffff 64bit pref]
[    0.302294] pci_bus 0000:02: resource 1 [mem 0xfe100000-0xfe1fffff]
[    0.302296] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]
[    0.302297] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]
[    0.302299] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
[    0.302300] pci_bus 0000:03: resource 7 [mem 0x000c8000-0x000dffff]
[    0.302302] pci_bus 0000:03: resource 8 [mem 0xc0000000-0xffffffff]
[    0.302303] pci_bus 0000:05: resource 0 [io  0xd000-0xdfff]
[    0.302305] pci_bus 0000:05: resource 2 [mem 0xd2100000-0xd21fffff 64bit pref]
[    0.302365] NET: Registered protocol family 2
[    0.302469] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.303289] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.305916] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.306244] TCP: Hash tables configured (established 524288 bind 65536)
[    0.306246] TCP reno registered
[    0.306254] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.306284] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.306425] NET: Registered protocol family 1
[    0.632115] pci 0000:01:00.0: Boot video device
[    0.632169] PCI: CLS 64 bytes, default 64
[    0.632213] Unpacking initramfs...
[    0.787967] Freeing initrd memory: 10140k freed
[    0.791465] PCI-DMA: Disabling AGP.
[    0.791553] PCI-DMA: aperture base @ b4000000 size 65536 KB
[    0.791554] PCI-DMA: using GART IOMMU.
[    0.791556] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    0.794187] IBS: LVT offset 1 assigned
[    0.794202] perf: AMD IBS detected (0x0000001f)
[    0.794387] audit: initializing netlink socket (disabled)
[    0.794399] type=2000 audit(1358783098.788:1): initialized
[    0.804217] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.804866] VFS: Disk quotas dquot_6.5.2
[    0.804902] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.804960] msgmni has been set to 7924
[    0.805145] alg: No test for stdrng (krng)
[    0.805182] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.805186] io scheduler noop registered
[    0.805187] io scheduler deadline registered
[    0.805200] io scheduler cfq registered (default)
[    0.805402] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.805422] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.805424] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.805650] ERST: Table is not found!
[    0.805651] GHES: HEST is not enabled!
[    0.805718] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.826109] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.880884] 00:0e: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.892300] Linux agpgart interface v0.103
[    0.892386] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.894685] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.894694] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.894830] mousedev: PS/2 mouse device common for all mice
[    0.894885] rtc_cmos 00:07: RTC can wake from S4
[    0.894999] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    0.895023] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.895033] cpuidle: using governor ladder
[    0.895034] cpuidle: using governor menu
[    0.895178] TCP cubic registered
[    0.895224] NET: Registered protocol family 10
[    0.895560] Mobile IPv6
[    0.895562] NET: Registered protocol family 17
[    0.895564] Registering the dns_resolver key type
[    0.895695] PM: Hibernation image not present or could not be loaded.
[    0.895702] registered taskstats version 1
[    0.896187] rtc_cmos 00:07: setting system clock to 2013-01-21 15:44:59 UTC (1358783099)
[    0.896235] Initializing network drop monitor service
[    0.897054] Freeing unused kernel memory: 576k freed
[    0.897186] Write protecting the kernel read-only data: 6144k
[    0.898969] Freeing unused kernel memory: 660k freed
[    0.901003] Freeing unused kernel memory: 680k freed
[    0.913040] udevd[49]: starting version 175
[    0.918179] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.927080] usbcore: registered new interface driver usbfs
[    0.927104] usbcore: registered new interface driver hub
[    0.930115] SCSI subsystem initialized
[    0.951931] usbcore: registered new device driver usb
[    0.952279] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.952333] ehci_hcd 0000:00:12.2: EHCI Host Controller
[    0.952359] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[    0.952370] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    0.952392] QUIRK: Enable AMD PLL fix
[    0.952401] ehci_hcd 0000:00:12.2: debug port 1
[    0.952424] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe209000
[    0.956080] libata version 3.00 loaded.
[    0.964060] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    0.964085] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.964087] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.964089] usb usb1: Product: EHCI Host Controller
[    0.964091] usb usb1: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[    0.964092] usb usb1: SerialNumber: 0000:00:12.2
[    0.964220] hub 1-0:1.0: USB hub found
[    0.964225] hub 1-0:1.0: 5 ports detected
[    0.964369] ehci_hcd 0000:00:13.2: EHCI Host Controller
[    0.964379] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[    0.964385] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    0.964406] ehci_hcd 0000:00:13.2: debug port 1
[    0.964421] ehci_hcd 0000:00:13.2: irq 17, io mem 0xfe207000
[    0.975671] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.975748] r8169 0000:05:00.0: setting latency timer to 64
[    0.975817] r8169 0000:05:00.0: irq 72 for MSI/MSI-X
[    0.976230] r8169 0000:05:00.0: eth0: RTL8168evl/8111evl at 0xffffc90000672000, bc:5f:f4:73:9f:06, XID 0c900800 IRQ 72
[    0.976232] r8169 0000:05:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    0.976243] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    0.976265] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.976266] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.976268] usb usb2: Product: EHCI Host Controller
[    0.976269] usb usb2: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[    0.976271] usb usb2: SerialNumber: 0000:00:13.2
[    0.976554] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.976626] hub 2-0:1.0: USB hub found
[    0.976629] hub 2-0:1.0: 5 ports detected
[    0.976793] ehci_hcd 0000:00:16.2: EHCI Host Controller
[    0.976802] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[    0.976809] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    0.976833] ehci_hcd 0000:00:16.2: debug port 1
[    0.976846] ehci_hcd 0000:00:16.2: irq 17, io mem 0xfe204000
[    0.976943] xhci_hcd 0000:02:00.0: setting latency timer to 64
[    0.976945] xhci_hcd 0000:02:00.0: xHCI Host Controller
[    0.976952] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 4
[    0.977029] xhci_hcd 0000:02:00.0: irq 48, io mem 0xfe100000
[    0.977067] xhci_hcd 0000:02:00.0: irq 73 for MSI/MSI-X
[    0.977102] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    0.977103] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.977105] usb usb4: Product: xHCI Host Controller
[    0.977106] usb usb4: Manufacturer: Linux 3.2.0-4-amd64 xhci_hcd
[    0.977107] usb usb4: SerialNumber: 0000:02:00.0
[    0.977173] xHCI xhci_add_endpoint called for root hub
[    0.977175] xHCI xhci_check_bandwidth called for root hub
[    0.977194] hub 4-0:1.0: USB hub found
[    0.977199] hub 4-0:1.0: 2 ports detected
[    0.977247] xhci_hcd 0000:02:00.0: xHCI Host Controller
[    0.977251] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 5
[    0.977262] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[    0.977264] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.977266] usb usb5: Product: xHCI Host Controller
[    0.977267] usb usb5: Manufacturer: Linux 3.2.0-4-amd64 xhci_hcd
[    0.977268] usb usb5: SerialNumber: 0000:02:00.0
[    0.977318] xHCI xhci_add_endpoint called for root hub
[    0.977319] xHCI xhci_check_bandwidth called for root hub
[    0.977337] hub 5-0:1.0: USB hub found
[    0.977342] hub 5-0:1.0: 2 ports detected
[    0.988050] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[    0.988075] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    0.988077] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.988079] usb usb3: Product: EHCI Host Controller
[    0.988080] usb usb3: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[    0.988081] usb usb3: SerialNumber: 0000:00:16.2
[    0.988291] hub 3-0:1.0: USB hub found
[    0.988295] hub 3-0:1.0: 4 ports detected
[    0.988578] ahci 0000:00:11.0: version 3.0
[    0.988688] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[    0.988691] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part sxs 
[    0.993577] scsi0 : ahci
[    0.993713] scsi1 : ahci
[    0.993810] scsi2 : ahci
[    0.993865] scsi3 : ahci
[    0.993956] ata1: SATA max UDMA/133 abar m1024@0xfe20b000 port 0xfe20b100 irq 19
[    0.993960] ata2: SATA max UDMA/133 abar m1024@0xfe20b000 port 0xfe20b180 irq 19
[    0.993964] ata3: SATA max UDMA/133 abar m1024@0xfe20b000 port 0xfe20b200 irq 19
[    0.993967] ata4: SATA max UDMA/133 abar m1024@0xfe20b000 port 0xfe20b280 irq 19
[    0.994423] scsi4 : pata_atiixp
[    0.994473] scsi5 : pata_atiixp
[    0.994578] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    0.994579] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    0.994859] ohci_hcd 0000:00:12.0: OHCI Host Controller
[    0.994872] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 6
[    0.994896] ohci_hcd 0000:00:12.0: irq 18, io mem 0xfe20a000
[    1.052053] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    1.052057] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.052059] usb usb6: Product: OHCI Host Controller
[    1.052060] usb usb6: Manufacturer: Linux 3.2.0-4-amd64 ohci_hcd
[    1.052061] usb usb6: SerialNumber: 0000:00:12.0
[    1.052197] hub 6-0:1.0: USB hub found
[    1.052202] hub 6-0:1.0: 5 ports detected
[    1.052299] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    1.052306] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 7
[    1.052323] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe208000
[    1.112042] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    1.112045] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.112046] usb usb7: Product: OHCI Host Controller
[    1.112048] usb usb7: Manufacturer: Linux 3.2.0-4-amd64 ohci_hcd
[    1.112049] usb usb7: SerialNumber: 0000:00:13.0
[    1.112189] hub 7-0:1.0: USB hub found
[    1.112194] hub 7-0:1.0: 5 ports detected
[    1.112558] ohci_hcd 0000:00:14.5: OHCI Host Controller
[    1.112565] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 8
[    1.112741] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe206000
[    1.173803] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    1.173806] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.173808] usb usb8: Product: OHCI Host Controller
[    1.173809] usb usb8: Manufacturer: Linux 3.2.0-4-amd64 ohci_hcd
[    1.173810] usb usb8: SerialNumber: 0000:00:14.5
[    1.173983] hub 8-0:1.0: USB hub found
[    1.173988] hub 8-0:1.0: 2 ports detected
[    1.174096] ohci_hcd 0000:00:16.0: OHCI Host Controller
[    1.174105] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 9
[    1.174122] ohci_hcd 0000:00:16.0: irq 18, io mem 0xfe205000
[    1.232110] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001
[    1.232113] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.232115] usb usb9: Product: OHCI Host Controller
[    1.232116] usb usb9: Manufacturer: Linux 3.2.0-4-amd64 ohci_hcd
[    1.232118] usb usb9: SerialNumber: 0000:00:16.0
[    1.232258] hub 9-0:1.0: USB hub found
[    1.232263] hub 9-0:1.0: 4 ports detected
[    1.312066] ata4: SATA link down (SStatus 0 SControl 300)
[    1.312110] ata3: SATA link down (SStatus 0 SControl 300)
[    1.484054] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.484080] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.486390] ata2.00: ATAPI: HL-DT-ST DVDRAM GH24NS95, RN00, max UDMA/133
[    1.488020] ata2.00: configured for UDMA/133
[    1.491675] ata1.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[    1.491678] ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.499654] ata1.00: configured for UDMA/133
[    1.499849] scsi 0:0:0:0: Direct-Access     ATA      WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
[    1.501606] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GH24NS95  RN00 PQ: 0 ANSI: 5
[    1.506060] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[    1.506063] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.506091] sd 0:0:0:0: [sda] Write Protect is off
[    1.506093] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.506105] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.516633] sr0: scsi3-mmc drive: 48x/12x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.516637] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.516759] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.518539]  sda: sda1 sda2
[    1.518852] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.520514] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.520578] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.548053] usb 6-1: new low-speed USB device number 2 using ohci_hcd
[    1.716139] usb 6-1: New USB device found, idVendor=046d, idProduct=c31c
[    1.716142] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.716144] usb 6-1: Product: USB Keyboard
[    1.716145] usb 6-1: Manufacturer: Logitech
[    1.730313] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb6/6-1/6-1:1.0/input/input1
[    1.730370] generic-usb 0003:046D:C31C.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:12.0-1/input0
[    1.741203] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:12.0/usb6/6-1/6-1:1.1/input/input2
[    1.741255] generic-usb 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:12.0-1/input1
[    1.741272] usbcore: registered new interface driver usbhid
[    1.741273] usbhid: USB HID core driver
[    1.792050] Refined TSC clocksource calibration: 3392.622 MHz.
[    1.792055] Switching to clocksource tsc
[    1.988052] usb 6-2: new low-speed USB device number 3 using ohci_hcd
[    1.994577] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    2.155147] usb 6-2: New USB device found, idVendor=046d, idProduct=c05b
[    2.155150] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.155152] usb 6-2: Product: USB Optical Mouse
[    2.155153] usb 6-2: Manufacturer: Logitech
[    2.162293] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb6/6-2/6-2:1.0/input/input3
[    2.162375] generic-usb 0003:046D:C05B.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:12.0-2/input0
[    3.367990] udevd[368]: starting version 175
[    4.096261] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[    4.096304] ACPI: Power Button [PWRB]
[    4.096349] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[    4.096370] ACPI: Power Button [PWRF]
[    4.108187] input: PC Speaker as /devices/platform/pcspkr/input/input6
[    4.335515] EDAC MC: Ver: 2.1.0
[    4.389361] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    4.396204] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[    4.396263] SP5100 TCO timer: mmio address 0xbafe00 already in use
[    4.558772] MCE: In-kernel MCE decoding enabled.
[    4.564151] AMD64 EDAC driver v3.4.0
[    4.564260] EDAC amd64: DRAM ECC disabled.
[    4.564267] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[    4.564268]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[    4.564269]  (Note that use of the override may cause unknown side effects.)
[    4.582307] [drm] Initialized drm 1.1.0 20060810
[    4.694717] powernow-k8: Found 1 AMD Athlon(tm) II X2 270 Processor (2 cpu cores) (version 2.20.00)
[    4.694765] powernow-k8:    0 : pstate 0 (3400 MHz)
[    4.694767] powernow-k8:    1 : pstate 1 (2700 MHz)
[    4.694768] powernow-k8:    2 : pstate 2 (2000 MHz)
[    4.694769] powernow-k8:    3 : pstate 3 (800 MHz)
[    4.795479] wmi: Mapper loaded
[    4.910407] nouveau 0000:01:00.0: setting latency timer to 64
[    4.914034] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x0a3280a2)
[    4.937479] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
[    5.022173] [drm] nouveau 0000:01:00.0: ... appears to be valid
[    5.022185] [drm] nouveau 0000:01:00.0: BIT BIOS found
[    5.022193] [drm] nouveau 0000:01:00.0: Bios version 70.15.4f.00
[    5.022202] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[    5.022209] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 4.0
[    5.022217] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000302 00020030
[    5.022225] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02000300 00000000
[    5.022231] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 01032310 00000000
[    5.022238] [drm] nouveau 0000:01:00.0: Raw DCB entry 3: 08021392 00020020
[    5.022247] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 16 4
[    5.022255] [drm] nouveau 0000:01:00.0:   0: 0x00001030: type 0x30 idx 0 tag 0x07
[    5.022262] [drm] nouveau 0000:01:00.0:   1: 0x00002161: type 0x61 idx 1 tag 0x08
[    5.022270] [drm] nouveau 0000:01:00.0:   2: 0x00000200: type 0x00 idx 2 tag 0xff
[    5.022280] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0x69F2
[    5.103595] [drm] nouveau 0000:01:00.0: 0x6D81: Condition still not met after 20ms, skipping following opcodes
[    5.123451] [drm] nouveau 0000:01:00.0: 0x6D85: Condition still not met after 20ms, skipping following opcodes
[    5.123486] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0x6FB0
[    5.131225] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0x831F
[    5.131239] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0x835D
[    5.176784] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0x85A7
[    5.176791] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0x860C
[    5.196644] [drm] nouveau 0000:01:00.0: 0x860C: Condition still not met after 20ms, skipping following opcodes
[    5.219029] [drm] nouveau 0000:01:00.0: 3 available performance level(s)
[    5.219042] [drm] nouveau 0000:01:00.0: 0: core 135MHz shader 270MHz memory 135MHz timing 2 voltage 900mV
[    5.219053] [drm] nouveau 0000:01:00.0: 1: core 405MHz shader 810MHz memory 324MHz timing 1 voltage 900mV
[    5.219065] [drm] nouveau 0000:01:00.0: 3: core 506MHz shader 1012MHz memory 800MHz timing 4 voltage 920mV
[    5.219100] [drm] nouveau 0000:01:00.0: c: core 405MHz shader 810MHz memory 324MHz voltage 970mV
[    5.222321] [TTM] Zone  kernel: Available graphics memory: 2029600 kiB.
[    5.222327] [TTM] Initializing pool allocator.
[    5.222353] [drm] nouveau 0000:01:00.0: Detected 1024MiB VRAM
[    5.223302] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[    5.248082] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[    5.290526] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    5.290533] [drm] No driver support for vblank timestamp query.
[    5.408074] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x320000, bo ffff8801383b0c00
[    5.408197] fbcon: nouveaufb (fb0) is primary device
[    5.461120] Console: switching to colour frame buffer device 128x48
[    5.462426] fb0: nouveaufb frame buffer device
[    5.462431] drm: registered panic notifier
[    5.462444] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 0
[    5.462584] hda_intel: Disabling MSI
[    5.462661] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[    6.280067] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[    6.312077] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[    6.344066] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[    6.376067] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[    6.392319] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input8
[    6.392586] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input9
[    6.392810] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input10
[    6.393022] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input11
[    7.273480] EXT4-fs (sda1): re-mounted. Opts: (null)
[    7.475591] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    7.568769] loop: module loaded
[    8.559312] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[    9.715344] RPC: Registered named UNIX socket transport module.
[    9.715353] RPC: Registered udp transport module.
[    9.715358] RPC: Registered tcp transport module.
[    9.715363] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    9.773380] FS-Cache: Loaded
[    9.827388] FS-Cache: Netfs 'nfs' registered for caching
[    9.855743] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   11.745251] vboxdrv: Found 2 processor cores.
[   11.745967] vboxdrv: fAsync=0 offMin=0x5c8 offMax=0x18eb
[   11.746202] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   11.746204] vboxdrv: Successfully loaded version 4.1.18_Debian (interface 0x00190000).
[   11.841805] vboxpci: IOMMU not found (not registered)
[   12.486847] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input12
[   14.041947] Bluetooth: Core ver 2.16
[   14.041993] NET: Registered protocol family 31
[   14.041999] Bluetooth: HCI device and connection manager initialized
[   14.042008] Bluetooth: HCI socket layer initialized
[   14.042013] Bluetooth: L2CAP socket layer initialized
[   14.042025] Bluetooth: SCO socket layer initialized
[   14.047496] Bluetooth: RFCOMM TTY layer initialized
[   14.047507] Bluetooth: RFCOMM socket layer initialized
[   14.047513] Bluetooth: RFCOMM ver 1.11
[   14.092367] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.092375] Bluetooth: BNEP filters: protocol multicast
[   14.359510] lp: driver loaded but no devices found
[   14.391654] ppdev: user-space parallel port driver
[   15.050587] r8169 0000:05:00.0: firmware: agent aborted loading rtl_nic/rtl8168e-3.fw (not found?)
[   15.051968] r8169 0000:05:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168e-3.fw (-2)
[   15.061011] r8169 0000:05:00.0: eth0: link down
[   15.062324] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.746125] r8169 0000:05:00.0: eth0: link up
[   16.747445] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   27.280049] eth0: no IPv6 routers present
[   74.517525] FS-Cache: Netfs 'cifs' registered for caching
[   74.600509] CIFS VFS: default security mechanism requested.  The default security mechanism will be upgraded from ntlm to ntlmv2 in kernel release 3.3
[ 4260.332110] usb 2-4: new high-speed USB device number 2 using ehci_hcd
[ 4260.466085] usb 2-4: New USB device found, idVendor=0781, idProduct=5571
[ 4260.466097] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4260.466104] usb 2-4: Product: Cruzer Fit
[ 4260.466110] usb 2-4: Manufacturer: SanDisk
[ 4260.466114] usb 2-4: SerialNumber: 4C532000001212100494
[ 4260.956975] Initializing USB Mass Storage driver...
[ 4260.957270] scsi6 : usb-storage 2-4:1.0
[ 4260.957487] usbcore: registered new interface driver usb-storage
[ 4260.957492] USB Mass Storage support registered.
[ 4261.958272] scsi 6:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.22 PQ: 0 ANSI: 5
[ 4261.960716] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 4261.963861] sd 6:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 4261.965220] sd 6:0:0:0: [sdb] Write Protect is off
[ 4261.965230] sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 4261.968691] sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4261.978377]  sdb: sdb1
[ 4261.982102] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 4262.316072] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 4486.440799] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 5058.284864] device eth0 entered promiscuous mode
[ 5092.855399] usb 2-4: USB disconnect, device number 2
[ 5239.025427] device eth0 left promiscuous mode
[ 5239.075845] device eth0 entered promiscuous mode
[ 5382.408077] device eth0 left promiscuous mode
[ 5385.160134] vboxnetflt: dropped 0 out of 18422 packets
[ 5462.345870] device eth0 entered promiscuous mode
[ 5469.590348] device eth0 left promiscuous mode
[ 5469.723842] device eth0 entered promiscuous mode
[58031.847697] device eth0 left promiscuous mode
[58031.999220] device eth0 entered promiscuous mode

varlog is impossible to open. It says that is not recognized file.

konsolebox · 01-22-2013, 03:58 AM

But the previous log is more important than that. You sure /var/log/messages is not accessible? Are you logged in as root?

m1rr0rm3 · 01-22-2013, 04:29 AM

You have several possibilities.

1. This particular computer you are using is an AMD64 processor. [who is the manufacturer?]
2. Are you using a logitech usb wireless mouse? if so just use the keyboard and a standard USB keyboard
3. you will have to edit the grub.conf file in your version of linux to get rid of the nouveau driver. it causes video issues with Nvidia.
look in /boot/grub/grub.conf paste the line [ what ever you must edit for your version ] at the end of your current version of boot.

4. go back to basics. start over if you have to.

[ 1.716144] usb 6-1: Product: USB Keyboard
[ 1.716145] usb 6-1: Manufacturer: Logitech

[ 2.155152] usb 6-2: Product: USB Optical Mouse
[ 2.155153] usb 6-2: Manufacturer: Logitech

[ 4.564151] AMD64 EDAC driver v3.4.0
[ 4.564260] EDAC amd64: DRAM ECC disabled.
[ 4.564267] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 4.564268] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 4.564269] (Note that use of the override may cause unknown side effects.)

[ 5.408074] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x320000, bo ffff8801383b0c00
[ 5.223302] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)

[ 5.408197] fbcon: nouveaufb (fb0) is primary device
[ 5.461120] Console: switching to colour frame buffer device 128x48
[ 5.462426] fb0: nouveaufb frame buffer device
[ 5.462431] drm: registered panic notifier
[ 5.462444] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 0

TobiSGD · 01-22-2013, 06:02 AM

Quote:

Originally Posted by m1rr0rm3

Generally the only reason for a freeze or a lock up on a computer is due to memory usage.

Sorry, but this is plain wrong. There are other factors that can cause a freeze, for example a faulty PSU or harddisk or an overheating CPU or GPU.

@miros84:
Please post more information:
- Is this a prebuilt machine or did you built it yourself?
- Which hardware are you actually using in the machine?
- Any peripheral devices that you were using with the installed system, but not with the live system?
- Which OS in which version?
- We need definitively some log data and maybe you can yourself make some observations, like:
-- Does the freeze occur under repeatable circumstances, like heavy load on CPU or GPU?
-- Does the freeze occur when you save/load large files?
-- Anything else that you could observe?

miros84 · 01-22-2013, 06:21 AM

Hi TobiSGD, happy join this issue.
I built this machine myself. I have beeb building computers long years ago, so I dont thing problem is the hardware error.

CPU is 2 core AMD athlon. Video Card is Nvidia GT220. Motherboard is Asrock 970Extreme
4GB RAM Kingston. As I said Live CD works fine. Today it doesnot froze.

I use very little CPU - about 5-10% and in both cases this happend when I was treing to open Chromium. And the third time I saw it is frozen one morning few days ago. I was working last night and I works OK, and next morning it was with black screen. Suspend is disabled.

I use Debian wheezy version.

Peripheral devices I use are logitech mouse and keyboard and d-link KVM Switch {conect ps2 and VGA (1 screen - 2 PCs)}

H_TeXMeX_H · 01-22-2013, 08:52 AM

Nothing special in dmesg, the only strange thing is:

Code:

[   15.050587] r8169 0000:05:00.0: firmware: agent aborted loading rtl_nic/rtl8168e-3.fw (not found?)

You might be missing some firmware ?

TobiSGD · 01-22-2013, 09:08 AM

Quote:

Originally Posted by H_TeXMeX_H

Nothing special in dmesg, the only strange thing is:

Code:

[   15.050587] r8169 0000:05:00.0: firmware: agent aborted loading rtl_nic/rtl8168e-3.fw (not found?)

You might be missing some firmware ?

You need to install the firmware-realtek package to get rid of this message. Without the firmware the network adapter will not support Gigabit-Ethernet, 10/100MBit still works.