LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Newbie
User Name
Password
Linux - Newbie This Linux forum is for members that are new to Linux.
Just starting out and have a question? If it is not in the man pages or the how-to's this is the place!

Notices


Reply
  Search this Thread
Old 01-26-2010, 09:35 AM   #1
salviablue
LQ Newbie
 
Registered: Jan 2010
Posts: 5

Rep: Reputation: 0
64studio won't boot into gui


Hi guys,
I have managed to install 64studio (32bit) after having to turn back the bios clock to 2007.
Now when it boots I get the whole:

Quote:
begin: waiting for root file system........
check root= bootarg cat /proc/cmdline or missing modules, devices: cat /proc/modules ls /dev
ALERT! /dev/hdb1 does not exist. Dropping to a shell!
/bin/sh: can't access tty; job control turned off
hda = primary master hd (storage - reiserfs, 2 parts) - MBR(?)
hdb = primary slave hd (many partitions)where 64 studio installed itself.

when i ls /dev, the only hd`s that turn up are hde`s, hdf's, hdg and hdet.
so i presumed that it had got confused somewhere, or just renamed the partitions, and that hde refered to hda and hdf refers to hdb. With that in mind editied the grub entry to root=hdf1 (with that being /) from root=hdb1.
Then on boot up i get:

Quote:
fsck.ext3: no such file or directory while trying to open /dev/hdb(*) -- * being any of the hdb (hdf) partitions i.e. this whole msg appears for all hdb partitions --
/dev/hdb(*):
this superblock could not be read or does not describe a correct ext2 filesystem. if the device is valid and it really contains an ext2 fs (and not swap or anything else), then the superblock is corrupt and you might try running e2fsck with an alternate superblock: e2fsck -b 8193

fsck died with exit status 8
failed (code 8)
file system check failed
blah blah
in the maintanence shell, everything seems to be read only.

if i ctrl-d and continue the boot it gives me a cmd line login for 64studio but after msgs like

Quote:
mount: special device /dev/hdb8 does not exist
mount: special device /dev/hdb5 does not exist
(etc,)
syslogd: var/log/syslog: no such file or directory
]
]and a long list of no such file or directory or command not found


now there seems to be lots of things about mdadm and raid failures etc. I do have a raid card, but there are no hd's attached. the only two hd's are those two mentioned previously, and those are ide.

Now I know it would be really advantageous to post here my dmesg etc. but that computer is not yet connected to the internet (awaiting broadband activation) and the only other internet access is through a usb dongle.

If someone can tell me how to write the dmesg to a usb stick (or similar) from the command prompt in initramfs or bash, then I may be able to get it on here.

Also I have had kubuntu/ubuntu, suse10.4 and several other linux os on this machine in the past with the same hardware.

Any help would be most appreciated.

Last edited by salviablue; 01-26-2010 at 09:53 AM. Reason: deletion of non essential info
 
Old 01-27-2010, 09:58 PM   #2
GlennsPref
Senior Member
 
Registered: Apr 2004
Location: Brisbane, Australia
Distribution: Devuan
Posts: 3,682
Blog Entries: 33

Rep: Reputation: 287Reputation: 287Reputation: 287
Hi, use redirect ">" to get dmesg to a file.

to add to an existing file use">>" With out quotes

Code:
dmesg > /media/win_c2/sorting/dmesg.txt
cheers, Glenn
 
Old 01-28-2010, 04:55 AM   #3
salviablue
LQ Newbie
 
Registered: Jan 2010
Posts: 5

Original Poster
Rep: Reputation: 0
Thankyou very much for that (should have looked it up my self really, just a little annoyed at this and the fact I seem to have forgotten so much about linux).

Here is the dmesg:
Code:
Linux version 2.6.21-1-multimedia-486 (Debian 2.6.21-2) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP PREEMPT RT Fri Jun 22 19:13:23 UTC 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end: 000000003fff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000003fff0000 size: 0000000000003000 end: 000000003fff3000 type: 4
copy_e820_map() start: 000000003fff3000 size: 000000000000d000 end: 0000000040000000 type: 3
copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
 BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 262128) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   262128
early_node_map[1] active PFN ranges
    0:        0 ->   262128
On node 0 totalpages: 262128
  DMA zone: 56 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4040 pages, LIFO batch:0
  Normal zone: 3080 pages used for memmap
  Normal zone: 222200 pages, LIFO batch:31
  HighMem zone: 447 pages used for memmap
  HighMem zone: 32305 pages, LIFO batch:7
DMI 2.2 present.
ACPI: RSDP 000F7390, 0014 (r0 VIA694)
ACPI: RSDT 3FFF3000, 0028 (r1 VIA694 AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 3FFF3040, 0074 (r1 VIA694 AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 3FFF30C0, 238D (r1 VIA694 AWRDACPI     1000 MSFT  100000C)
ACPI: FACS 3FFF0000, 0040
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000)
Real-Time Preemption Support (C) 2004-2007 Ingo Molnar
Built 1 zonelists.  Total pages: 258545
Kernel command line: root=/dev/hdf1 ro vga=791 splash=silent single
bootsplash: silent mode.
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01e8c000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
WARNING: experimental RCU implementation.
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2006.948 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1023540k/1048512k available (1720k kernel code, 24240k reserved, 680k data, 308k init, 131008k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4e000 - 0xfffff000   ( 708 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc035f000 - 0xc03ac000   ( 308 kB)
      .data : 0xc02ae041 - 0xc03580d4   ( 680 kB)
      .text : 0xc0100000 - 0xc02ae041   (1720 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4015.75 BogoMIPS (lpj=2007878)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000
Enabling disabled K7/SSE Support.
CPU: CLK_CTL MSR was fff7f37f. Reprogramming to 2007f37f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000420 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0800 (from 0e00)
CPU0: AMD Athlon(tm) Processor stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
PCI quirk: region 5000-500f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
pnp: 00:00: iomem range 0xd0000-0xd3fff has been reserved
pnp: 00:00: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:00: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: a000-afff
  MEM window: e8000000-e9ffffff
  PREFETCH window: d8000000-e7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 65536 (order: 9, 2883584 bytes)
TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Switched to NOHz mode on CPU #0
Freeing initrd memory: 5499k freed
audit: initializing netlink socket (disabled)
audit(1169980334.680:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 6144k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:5767
vesafb: pmi: set display start = c00c57fb, set palette = c00c5847
vesafb: pmi: ports = a010 a016 a054 a038 a03c a05c a000 a004 a0b0 a0b2 a0b4 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 82817 bytes,<6>...found (1024x768, 67122 bytes, v3).
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 308k freed
input: AT Translated Set 2 keyboard as /class/input/input0
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:00:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:00:0c.0: Try the "8139too" driver instead.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000b400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:09.2[C] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
8139too Fast Ethernet driver 0.9.28
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:09.2: irq 11, io mem 0xeb000000
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000b800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-4: new high speed USB device using ehci_hcd and address 2
IT8212: IDE controller at PCI slot 0000:00:0b.0
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
IT8212: chipset revision 19
it821x: controller in smart mode.
IT8212: 100% native mode on irq 11
usb 2-4: configuration #1 chosen from 1 choice
hub 2-4:1.0: USB hub found
hub 2-4:1.0: 4 ports detected
    ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
usb 2-4.1: new high speed USB device using ehci_hcd and address 3
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:09.0: irq 11, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
usb 2-4.1: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
    ide2: BM-DMA at 0xb000-0xb007, BIOS settings: hde:DMA, hdf:DMA
    ide3: BM-DMA at 0xb008-0xb00f, BIOS settings: hdg:DMA, hdh:pio
Probing IDE interface ide2...
hde: WDC WD1200BB-22GUA0, ATA DISK drive
hdf: SAMSUNG SV6004H, ATA DISK drive
ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide3...
hdg: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive
ide3 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:09.1[B] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:09.1: irq 10, io base 0x0000cc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
libata version 2.20 loaded.
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0xec00, 00:10:a7:21:16:e0, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
hde: max request size: 512KiB
hde: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hde: cache flushes supported
 hde: hde1
hdf: max request size: 128KiB
hdg: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdf: Host Protected Area detected.
	current capacity is 66055248 sectors (33820 MB)
	native  capacity is 117306000 sectors (60060 MB)
hdf: Host Protected Area disabled.
hdf: 117306000 sectors (60060 MB) w/468KiB Cache, CHS=65535/16/63, UDMA(100)
hdf: cache flushes supported
 hdf: hdf1 hdf2 < hdf5 hdf6 hdf7 hdf8 hdf9 >
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid5: measuring checksumming speed
   8regs     :  3012.000 MB/sec
   8regs_prefetch:  2740.000 MB/sec
   32regs    :  2048.000 MB/sec
   32regs_prefetch:  1816.000 MB/sec
raid5: using function: 8regs (3012.000 MB/sec)
raid6: int32x1    648 MB/s
raid6: int32x2    812 MB/s
raid6: int32x4    671 MB/s
raid6: int32x8    492 MB/s
raid6: mmxx1     1609 MB/s
raid6: mmxx2     2593 MB/s
raid6: sse1x1    1476 MB/s
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access              Flash Disk       5.00 PQ: 0 ANSI: 2
SCSI device sda: 4125184 512-byte hdwr sectors (2112 MB)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 4125184 512-byte hdwr sectors (2112 MB)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
raid6: sse1x2    2375 MB/s
raid6: using algorithm sse1x2 (2375 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Linux agpgart interface v0.102 (c) Dave Jones
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
agpgart: AGP aperture is 128M @ 0xd0000000
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
gameport: EMU10K1 is pci0000:00:0a.1/gameport0, io 0xd400, speed 1242kHz
Serial: 8250/16550 driver $Revision: 1.90 $ 10 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
8250_pnp: Unknown symbol serial8250_unregister_port
8250_pnp: Unknown symbol serial8250_resume_port
8250_pnp: Unknown symbol serial8250_register_port
8250_pnp: Unknown symbol serial8250_suspend_port
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: VIA VLink IRQ fixup for 0000:00:07.5, from 9 to 10
PCI: Setting latency timer of device 0000:00:07.5 to 64
EXT3 FS on hdf1, internal journal

Last edited by salviablue; 01-28-2010 at 09:17 AM.
 
Old 01-28-2010, 04:58 AM   #4
salviablue
LQ Newbie
 
Registered: Jan 2010
Posts: 5

Original Poster
Rep: Reputation: 0
Its probably me having done/not done something stupid/basic etc..

Could this be either something to do with it getting confused between the naming of the partitions (hdbx/hdfx)?, or a knackered hd?

Thanks again in advance.

(sorry i had to do it in two posts, the damn thing kept tellin gme i had too many images!! (what images?) sorted it, my fault, sorry, was using quote instead of code

Last edited by salviablue; 01-28-2010 at 09:20 AM.
 
Old 01-28-2010, 06:05 AM   #5
craigevil
Senior Member
 
Registered: Apr 2005
Location: OZ
Distribution: Debian Sid/RPIOS
Posts: 4,903
Blog Entries: 29

Rep: Reputation: 537Reputation: 537Reputation: 537Reputation: 537Reputation: 537Reputation: 537
IDk about 64Studio security support, but Debian support for Etch ends in mid February.

Personally I would either install Debian or perhaps Ubuntu Studio, Rather than run a distro that is that old.
 
Old 01-28-2010, 09:30 AM   #6
salviablue
LQ Newbie
 
Registered: Jan 2010
Posts: 5

Original Poster
Rep: Reputation: 0
Thing is, its an equally old computer, and I have run into problems before trying to install an up to date distro on old equipment, besides this one wouldn't be on line, not the 64studio o/s at any rate so security isn't really an issue. Plus, if i was to dl another distro, i'd exceed my data quota for the month, although, having said that, there are only a few more days left, though it'll have to wait until next month so as not to any data/band width throttling.

I'll try that, but I'd still like to know, why at least, 64studio isn't going.

Thankyou for your replies.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
Boot to Win XP leaves 64Studio without net connection drudge Linux - Newbie 2 10-26-2009 11:20 AM
change from Hardy Heron to 64Studio vanwin Linux - Newbie 2 10-23-2008 11:07 AM
32 bit 64Studio not found pgabhart Linux - Software 4 04-09-2007 10:53 PM
No Sound - nVidia ad1968a chip on 64Studio isync Linux - General 3 03-01-2007 09:24 AM
dyne:bolic vs 64studio tallman19 Linux - Distributions 1 12-20-2006 04:42 AM

LinuxQuestions.org > Forums > Linux Forums > Linux - Newbie

All times are GMT -5. The time now is 08:00 AM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration