Hauppauge PVR-350
I've got a Hauppauge PVR-350 installed. As far as I can tell everything is installed correctly:
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.4.5 (tagged release) loading
ivtv: Linux version: 2.6.13-15.8-default 586 REGPARM gcc-4.0
ivtv: In case of problems please include the debug info between
ivtv: the START INIT IVTV and END INIT IVTV lines, along with
ivtv: any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 350 card (cx23415 based)
tveeprom: ivtv version
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
saa7115 0-0021: ivtv driver
saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
saa7127 0-0044: ivtv driver
saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
msp3400 0-0040: ivtv driver
ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40]
tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv0: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
However, when I try to run xawtv all I get is a blank screen. I've got the coax cable from my satellite receiver going into the Hauppauge. Here's the info I've got so far. Any assistance is greatly appreciated.
ivtvctl -I
check SAA7115 input signal
ioctl: VIDEO_STATUS = Sat/Dvd
SAA7115 reg[STATUS#1 - 0x1E] = 81
Color Standard (D0-D1): NTSC
White peak loop (D2): Not activated
Gain value for act.lum. (min) (D3): Not limited
Gain value for act.lum. (max) (D4): Not limited
WIPA-mode slow-time constant (D5): Not activated
Horizontal frequency (D6): Locked
Field length (D7): Standard
SAA7115 reg[STATUS#2 - 0x1F] = b1
Ready for capture (D0): Yes
Macrovision 7.01 (D1): No
MV Colorstripe burst (D2): No
MV Colorstripe burst type 3 (D3): No
Input signal timebase (D4): Stable (broadcast/DVD)
Field frequency (D5): 60Hz
H & V loops (D6): Locked
Interlace (D7): Detected
|