Hi,
I'm trying to install an Edimax EW-7128g PCI wireless card. I have installed the drivers for this, but I can't pick up the card. According to this wiki (
http://ndiswrapper.sourceforge.net/m...index.php/List) the pci id should be 1818:0201. However I can't find this in lspci:
lspci -n:
0000:00:00.0 0600: 1106:0269
0000:00:00.1 0600: 1106:1269
0000:00:00.2 0600: 1106:2269
0000:00:00.3 0600: 1106:3269
0000:00:00.4 0600: 1106:4269
0000:00:00.7 0600: 1106:7269
0000:00:01.0 0604: 1106:b198
0000:00:0f.0 0104: 1106:3149 (rev 80)
0000:00:0f.1 0101: 1106:0571 (rev 06)
0000:00:10.0 0c03: 1106:3038 (rev 81)
0000:00:10.1 0c03: 1106:3038 (rev 81)
0000:00:10.2 0c03: 1106:3038 (rev 81)
0000:00:10.3 0c03: 1106:3038 (rev 81)
0000:00:10.4 0c03: 1106:3104 (rev 86)
0000:00:11.0 0601: 1106:3227
0000:00:11.5 0401: 1106:3059 (rev 60)
0000:00:12.0 0200: 1106:3065 (rev 78)
0000:01:00.0 0300: 10de:0322 (rev a1)
lspci:
0000:00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0269
0000:00:00.1 Host bridge: VIA Technologies, Inc.: Unknown device 1269
0000:00:00.2 Host bridge: VIA Technologies, Inc.: Unknown device 2269
0000:00:00.3 Host bridge: VIA Technologies, Inc.: Unknown device 3269
0000:00:00.4 Host bridge: VIA Technologies, Inc.: Unknown device 4269
0000:00:00.7 Host bridge: VIA Technologies, Inc.: Unknown device 7269
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [K8T800 South]
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
0000:01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
I've put the dmesg output below:
lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1596.233 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1031388k/1048512k available (1595k kernel code, 16384k reserved, 721k data, 164k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3153.92 BogoMIPS (lpj=1576960)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000020 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4584k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb3d0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to
bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x4000-0x407f could not be reserved
pnp: 00:01: ioport range 0x5000-0x500f has been reserved
audit: initializing netlink socket (disabled)
audit(1127395012.517:0): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
PCI0 USB3 USB4 USB5 USB6 USB7 LAN0 AC97 UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4584KiB [1 disk] into ram disk... |./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.\.|./.-.done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 164k freed
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (39 C)
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.10 loaded.
sata_via version 1.1
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via(0000:00:0f.0): routed to hard irq line 4
ata1: SATA max UDMA/133 cmd 0xE000 ctl 0xE102 bmdma 0xE400 irq 20
ata2: SATA max UDMA/133 cmd 0xE200 ctl 0xE302 bmdma 0xE408 irq 20
ata1: dev 0 cfg 49:2f00 82:346b 83:5b01 84:4003 85:3469 86:1a01 87:4003 88:407f
ata1: dev 0 ATA, max UDMA/133, 156301488 sectors:
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
elevator: using anticipatory as default io scheduler
Vendor: ATA Model: WDC WD800JD-55JR Rev: 05.0
Type: Direct-Access ANSI SCSI revision: 05
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Stopping tasks: ===|
Freeing memory... .-.\.|./.-.done (483 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1
EXT3 FS on sda1, internal journal
Probing IDE interface ide0...
hda: Maxtor 6L300R0, ATA DISK drive
hdb: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 586114704 sectors (300090 MB) w/16384KiB Cache, CHS=36483/255/63
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
ndiswrapper version 1.0rc2 loaded (preempt=yes,smp=no)
ndiswrapper (wrapper_init:1494): loadndiswrapper failed (1792); check system log for messages from 'loadndisdriver'
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised:
dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-k7
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT880 chipset
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xe8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
VP_IDE: port 0x01f0 already claimed by ide0
ide1: BM-DMA at 0xe608-0xe60f, BIOS settings: hdc
io, hdd
io
Probing IDE interface ide1...
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 21, io base 0xe700
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 21, io base 0xe800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 21, io base 0xe900
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: irq 21, io base 0xea00
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: irq 21, pci mem 0xfa000000
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-1: USB disconnect, address 2
via82xx: Assuming DXS channels with 48k fixed sample rate.
Please try dxs_support=1 or dxs_support=4 option
and report if it works on your machine.
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 2-1: new full speed USB device using uhci_hcd and address 3
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb 3-1: new full speed USB device using uhci_hcd and address 2
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 23
eth0: VIA Rhine II at 0xec00, 00:30:18:a2:97:a6, IRQ 23.
eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000.
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
eth0: link down
NET: Registered protocol family 17
Vendor: OTi Model: Ultra Floppy Rev: 1.11
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdb: 32256 512-byte hdwr sectors (17 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 32256 512-byte hdwr sectors (17 MB)
sdb: Write Protect is off
sdb: Mode Sense: 03 00 00 00
sdb: assuming drive cache: write through
/dev/scsi/host3/bus0/target0/lun0: p1
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
usb-storage: device scan complete
Vendor: OEI-USB Model: CompactFlash Rev: 2.0
Type: Direct-Access ANSI SCSI revision: 00
Attached scsi removable disk sdc at scsi4, channel 0, id 0, lun 0
Vendor: OEI-USB Model: SM/MS/SD Rev: 2.0
Type: Direct-Access ANSI SCSI revision: 00
Attached scsi removable disk sdd at scsi4, channel 0, id 0, lun 1
usb-storage: device scan complete
ndiswrapper version 1.0rc2 loaded (preempt=yes,smp=no)
ndiswrapper (wrapper_init:1494): loadndiswrapper failed (1792); check system log for messages from 'loadndisdriver'
ndiswrapper version 1.0rc2 loaded (preempt=yes,smp=no)
ndiswrapper (wrapper_init:1494): loadndiswrapper failed (1792); check system log for messages from 'loadndisdriver'
ndiswrapper version 1.0rc2 loaded (preempt=yes,smp=no)
ndiswrapper (wrapper_init:1494): loadndiswrapper failed (1792); check system log for messages from 'loadndisdriver'
ndiswrapper version 1.0rc2 loaded (preempt=yes,smp=no)
ndiswrapper (wrapper_init:1494): loadndiswrapper failed (1792); check system log for messages from 'loadndisdriver'
ndiswrapper version 1.0rc2 loaded (preempt=yes,smp=no)
ndiswrapper (wrapper_init:1494): loadndiswrapper failed (1792); check system log for messages from 'loadndisdriver'
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0315d40(lo)
IPv6 over IPv4 tunneling driver
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
eth0: no IPv6 routers present
---
Any help greatly appreciated!!!
