LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Home Forums Tutorials Articles Register
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware
Reload this Page NetMOS PCI 9835 Dual Serial Card Problem
User Name
Password
Linux - Hardware This forum is for Hardware issues.
Having trouble installing a piece of hardware? Want to know if that peripheral is compatible with Linux?

Notices


Reply
  Search this Thread
Old 02-20-2009, 04:04 PM   #1
mrgadgetnz
LQ Newbie
 
Registered: Feb 2009
Posts: 1

Rep: Reputation: 0
Question NetMOS PCI 9835 Dual Serial Card Problem

Hi,

I've installed a dual-port serial card based on the NetMOS 9835 chipset. I've followed the serial instructions, but everything they tell me to do is already done - see setserial outputs below. I've compared these values to the lspci output (below, card is at the bottom of the output) for the card and it appears right. Problem being, I can't use the serial ports.

Oh and I did use search, and looked at every 9835-related article before posting this

Any ideas would be much appreciated

Cheers,
Ben

Code:
[root@intelliHome /]# setserial -a /dev/ttyS2
/dev/ttyS2, Line 2, UART: 16550A, Port: 0x1010, IRQ: 169
        Baud_base: 115200, close_delay: 50, divisor: 0
        closing_wait: 3000
        Flags: spd_normal skip_test

[root@intelliHome /]# setserial -a /dev/ttyS3
/dev/ttyS3, Line 3, UART: 16550A, Port: 0x1018, IRQ: 169
        Baud_base: 115200, close_delay: 50, divisor: 0
        closing_wait: 3000
        Flags: spd_normal skip_test

################################################################################################

[root@intelliHome /]# dmesg | grep tty
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
0000:05:09.0: ttyS2 at I/O 0x1010 (irq = 169) is a 16550A
0000:05:09.0: ttyS3 at I/O 0x1018 (irq = 169) is a 16550A

################################################################################################

[root@intelliHome /]# lspci -vv
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
        Subsystem: Hewlett-Packard Company d330 uT
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [e4] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
        Subsystem: Hewlett-Packard Company D530 sff(dc578av)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
        Region 1: Memory at fc400000 (32-bit, non-prefetchable) [size=512K]
        Region 2: I/O ports at 24e0 [size=8]
        Capabilities: [d0] Power Management version 1
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 185
        Region 4: I/O ports at 2440 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 193
        Region 4: I/O ports at 2460 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 169
        Region 4: I/O ports at 2480 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 177
        Region 0: Memory at fc480000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
        I/O behind bridge: 00001000-00001fff
        Memory behind bridge: fc500000-fc7fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 169
        Region 0: I/O ports at <ignored>
        Region 1: I/O ports at <ignored>
        Region 2: I/O ports at <ignored>
        Region 3: I/O ports at <ignored>
        Region 4: I/O ports at 24c0 [size=16]
        Region 5: Memory at 50000000 (32-bit, non-prefetchable) [size=1K]

00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 169
        Region 0: I/O ports at 24f8 [size=8]
        Region 1: I/O ports at 2810 [size=4]
        Region 2: I/O ports at 2800 [size=8]
        Region 3: I/O ports at 2814 [size=4]
        Region 4: I/O ports at 24d0 [size=16]

00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
        Subsystem: Hewlett-Packard Company d330 uT
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 209
        Region 0: I/O ports at 2000 [size=256]
        Region 1: I/O ports at 2400 [size=64]
        Region 2: Memory at fc480400 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at fc480600 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

05:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5782 Gigabit Ethernet (rev 03)
        Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (16000ns min), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 201
        Region 0: Memory at fc500000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at <ignored> [disabled]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
        Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
                Address: ffddbefffffffffc  Data: dfff

05:09.0 Serial controller: NetMos Technology PCI 9835 Multi-I/O Controller (rev 01) (prog-if 02 [16550])
        Subsystem: LSI Logic / Symbios Logic 2S (16C550 UART)
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 169
        Region 0: I/O ports at 1010 [size=8]
        Region 1: I/O ports at 1018 [size=8]
        Region 2: I/O ports at 1020 [size=8]
        Region 3: I/O ports at 1028 [size=8]
        Region 4: I/O ports at 1030 [size=8]
        Region 5: I/O ports at 1000 [size=16]
 
  


Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
NetMos PCI Multi I/O 9835 problem pollictor Linux - Hardware 3 07-01-2009 05:44 AM
netmos 9845, 9835 on slack 12.1 = double failure thatquietboy Slackware - Installation 2 06-30-2008 05:48 PM
Netmos 9835 PCI Serial I/O Addon and HIGH CPU USAGE yunias Linux - Hardware 0 10-18-2005 03:33 AM
netmos 9835 controller Daniel49 Linux - Hardware 1 08-01-2005 05:48 AM
NetMos 9835 serial port card Asad Linux - Hardware 1 03-26-2005 01:26 AM

LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware

All times are GMT -5. The time now is 01:11 AM.

Contact Us - Advertising Info - Rules - Privacy - LQ Merchandise - Donations - Contributing Member - LQ Sitemap -
Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration