|
I have testet
"slarm64-current-aarch64-xfce-orange_pi_3_lts-6.1.11-build-20230212.img"
by micro-SDcard. Boot fails. Same bevaviour shows image
"slarm64-current-aarch64-core-orange_pi_3_lts-6.1.11-build-20230212.img".
Here the Log of xfce-image:
U-Boot SPL 2022.10-sun50iw6 (Feb 11 2023 - 22:42:30 +0200)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.7(release):v2.7.0
NOTICE: BL31: Built : 22:41:53, Feb 11 2023
NOTICE: BL31: Detected Allwinner H6 SoC (1728)
NOTICE: BL31: Found U-Boot DTB at 0xa087528, model: OrangePi 3 LTS
ERROR: RSB: read command: 0x103
ERROR: RSB: write command: 0x3
ERROR: RSB: read command: 0x103
ERROR: RSB: write command: 0x3
ERROR: RSB: read command: 0x3
ERROR: RSB: write command: 0x3
ERROR: RSB: read command: 0x3
ERROR: RSB: write command: 0x3
ERROR: RSB: read command: 0x103
ERROR: RSB: write command: 0x3
ERROR: RSB: read command: 0x3
ERROR: RSB: write command: 0x3
ERROR: RSB: read command: 0x3
ERROR: RSB: write command: 0x3
U-Boot 2022.10-sun50iw6 (Feb 11 2023 - 22:42:30 +0200) Allwinner Technology
CPU: Allwinner H6 (SUN50I)
Model: OrangePi 3 LTS
DRAM: 2 GiB
Core: 50 devices, 14 uclasses, devicetree: separate
WDT: Not starting watchdog@7020400
MMC: mmc@4020000: 0, mmc@4022000: 1
Loading Environment from FAT... Unable to use mmc 0:1...
In: serial@5000000
Out: serial@5000000
Err: serial@5000000
Net: No ethernet found.
Autoboot in 2 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
2716 bytes read in 2 ms (1.3 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
147 bytes read in 2 ms (71.3 KiB/s)
38625 bytes read in 7 ms (5.3 MiB/s)
23142408 bytes read in 1117 ms (19.8 MiB/s)
4191 bytes read in 5 ms (818.4 KiB/s)
Applying kernel provided DT fixup script (sun50i-h6-fixup.scr)
## Executing script at 45000000
6266815 bytes read in 312 ms (19.2 MiB/s)
Moving Image from 0x40080000 to 0x40200000, end=41880000
## Loading init Ramdisk from Legacy Image at 4ff00000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 6266751 Bytes = 6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
Booting using the fdt blob at 0x4fa00000
Loading Ramdisk to 49a06000, end 49ffff7f ... OK
Loading Device Tree to 0000000049994000, end 0000000049a05fff ... OK
Starting kernel ...
[ 1.164722] scpi_protocol scpi: incorrect or no SCP firmware found
[ 1.166465] axp20x-rsb sunxi-rsb-745: Failed to set masks in 0x40: -5
[ 1.166490] axp20x-rsb sunxi-rsb-745: failed to add irq chip: -5
[ 1.217051] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 102
[ 1.217076] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 65
[ 1.224044] sun50i-h6-pinctrl 300b000.pinctrl: pin-102 (300b000.pinctrl:102) status -517
[ 1.224056] sun50i-h6-pinctrl 300b000.pinctrl: pin-65 (4022000.mmc) status -517
[ 1.224066] sun50i-h6-pinctrl 300b000.pinctrl: could not request pin 65 (PC1) from group PC1 on device 300b000.pinctrl
[ 1.231992] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 79
[ 1.239028] sunxi-mmc 4022000.mmc: Error applying setting, reverse things back
[ 1.271215] sun50i-h6-pinctrl 300b000.pinctrl: pin-79 (300b000.pinctrl:79) status -517
[ 1.281812] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 102
[ 1.288811] sun50i-h6-pinctrl 300b000.pinctrl: pin-102 (300b000.pinctrl:102) status -517
[ 1.298225] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 65
[ 1.298246] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 79
[ 1.305143] sun50i-h6-pinctrl 300b000.pinctrl: pin-65 (4022000.mmc) status -517
[ 1.312011] sun50i-h6-pinctrl 300b000.pinctrl: pin-79 (300b000.pinctrl:79) status -517
[ 1.312023] sun50i-h6-pinctrl 300b000.pinctrl: could not request pin 65 (PC1) from group PC1 on device 300b000.pinctrl
[ 1.314145] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 102
[ 1.319354] sunxi-mmc 4022000.mmc: Error applying setting, reverse things back
[ 1.352255] sun50i-h6-pinctrl 300b000.pinctrl: pin-102 (300b000.pinctrl:102) status -517
[ 1.360740] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 79
[ 1.367629] sun50i-h6-pinctrl 300b000.pinctrl: pin-79 (300b000.pinctrl:79) status -517
[ 1.378360] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 65
[ 1.378413] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 102
[ 1.385267] sun50i-h6-pinctrl 300b000.pinctrl: pin-65 (4022000.mmc) status -517
[ 1.385277] sun50i-h6-pinctrl 300b000.pinctrl: could not request pin 65 (PC1) from group PC1 on device 300b000.pinctrl
[ 1.385293] sun50i-h6-pinctrl 300b000.pinctrl: pin-102 (300b000.pinctrl:102) status -517
[ 1.392256] sunxi-mmc 4022000.mmc: Error applying setting, reverse things back
[ 1.521592] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 79
[ 1.528534] sun50i-h6-pinctrl 300b000.pinctrl: pin-79 (300b000.pinctrl:79) status -517
[ 1.540025] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 102
[ 1.540179] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 65
[ 1.547062] sun50i-h6-pinctrl 300b000.pinctrl: pin-102 (300b000.pinctrl:102) status -517
[ 1.547082] sun50i-h6-pinctrl 300b000.pinctrl: pin-65 (4022000.mmc) status -517
[ 1.569397] sun50i-h6-pinctrl 300b000.pinctrl: could not request pin 65 (PC1) from group PC1 on device 300b000.pinctrl
[ 1.580226] sunxi-mmc 4022000.mmc: Error applying setting, reverse things back
[ 11.493043] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 79
[ 11.499985] sun50i-h6-pinctrl 300b000.pinctrl: pin-79 (300b000.pinctrl:79) status -517
[ 11.510533] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 102
[ 11.517517] sun50i-h6-pinctrl 300b000.pinctrl: pin-102 (300b000.pinctrl:102) status -517
[ 11.525684] sun50i-h6-pinctrl 300b000.pinctrl: request() failed for pin 65
[ 11.532594] sun50i-h6-pinctrl 300b000.pinctrl: pin-65 (4022000.mmc) status -517
[ 11.539937] sun50i-h6-pinctrl 300b000.pinctrl: could not request pin 65 (PC1) from group PC1 on device 300b000.pinctrl
[ 11.550731] sunxi-mmc 4022000.mmc: Error applying setting, reverse things back
###########
end of kernelmessages
Has experts any idea, what runnnig wrong ?
Depend fails on u-boot (kernelparameters) or kernel ?
I tried to boot with Armbian current rolling release of 6.1.11 kernel.
Boot runs without issues and X11 start successfull.
Unfortunatly I need SysVinit boot and Motif library,
what's with slarm64-images is given.
|
