Quote:
Quote:
Code:
ls -l |
Bad news. No such file or directory as x11 or xll No wonder I am having such problems. Did find /etc. xoneone or xLL, LOWER CASE
I will try reloading 9.10 from disc. If that fails I will dld something that takes control and does it all by itself. I think it is wubi 9+.10 I expect both to fail. If they do, I will dld debian. |
I recall X11 (x one one) is uppercase, regret I am at my work XP system with no access to anything Linux. If you are looking for a file, there are several ways. Terminal is quicker than gui.
Code:
cd /etc Code:
cd /etc If you are changing to Debian, see http://www.debian.org/releases/etch/ My old hardware definitely worked on this now superceded release. I think I was OK with "Lenny" which is now the stable distro, but can't go back and check now. "Etch" was fine. My monitor was unable to change resolution until I updated horizsync vertrefresh and depth, but xorg.conf accepted manual settings without difficulty. |
You were right. It is Xoneone
s1 is pretty, but dir gets the same results in b & w. The results are X Xsession.dxwrapper.config default display manager xinit xresourceses xsesion.options fonts xkb xsession xumcconfig cursors rgb.txt# I don't know how accurate I got these, but keep that in mind for your reply if any. Is that xorg or Xorg. Damn I wish I could access the printer on this network. It would be easier than transcribing notes. I forget what else I had to say. There ia an X11 folder. /etc/x11. I think I might better try debian. We aren't getting anywhere very fast. If it gets the display corect I should stick with it. My older puter has, a different g card and monitor. It has always managed to get it right. I have tried mandrake,three different ubuntus, and one other on it. It has always got it right. The only thing holding me back is the lan card quit. |
Other places for your xorg.conf
/etc/X11/xinit /usr/X11R6/lib/X11/ /usr/X11R6/lib/X11/xinit and _just_possibly_ /etc/X11/config |
After research I now know why you can't find your xorg.conf file- it's not there any more!:doh:
Although Code:
sudo xorg -configure May I suggest you download and burn your Debian Lenny I386 32 bit iso, make sure its Ok. Then, if you feel like a last try with xorg -configure, boot into ubuntu, and go for it. I think this process might be too difficult for a new user (and for some moderately experienced ones too! Like me) so after this attempt, see whether Debian can help you. |
Are you sure that is not xorg reconfigure. I saw that somewhere. It seems to fit the situation.
I will try the debian suggestion as soon as I get a disk. I am all out. Meanwhile, if it does wright a new config file, would the old suggestions work with it? I think the reason I couldn't find my way back was the title got changed and I didn't look at it quite right. I probably actually found it. Seeing the new title, I just ignored it. I hope I learned something from it. |
X -configure works here.
|
Although earlier in this thread I was recalling my own experience, with the Xorg command I am using posts on other forums therefore less confident. It has been noted that, if /etc/X11/xorg.conf is present, settings will be loaded from it. If this is the case, then my suggestions would be worth a try. This is from the man page on my 9.10, it's netbook remix but I don't think that would affect this command:
Code:
NAME I have found some limited info on the x command but not x -configure. But just because I haven't found it doesn't mean it's not there... try both. |
Before I forget, my grub 1st menu has a few extra lines having coming from repeated tries. What is the way to remove them.
A new install from disk didn't help anything. |
In the terminal, run this:
Code:
sudo gedit /boot/grub/menu.lst That will open your menu.lst in gedit (text editor) and then you can delete anything not needed. |
I assume we are still with Ubuntu? If so there have been some changes. The file that determines what you see on boot is /boot/grub/grub.cfg. Entries may be removed by editing this file but ubuntu community documentation seems to advise against this. If I had to remove an entry (eg because the kernel it referred to had gone) I would comment out the relevant lines in that file.
But it's best to leave a working system alone. Only play with the MBR and bootloader files (includes grub.cfg) when you are confident to repair it from a live session if it won't boot. With Debian AFAIK it's still menu.lst, but I haven't used Debian for a few months so not sure. Edit: just saw BrianL's post.. I have checked against my own 9.10 & here it is grub.cfg- removal of redundant kernels would I think be the same but I would reiterate warning about leaving alone for now. |
Aha, so it's grub.cfg now is it? I haven't tried Ubuntu since 9.04.
|
Yep, despite dire warning on community howto (not designed to be edited by user, even root) there doesn't appear to be a "vigrubbo" to edit it, suppose update-grub would do the syntax checking. So if I edit it, I'll leave usual ways back, copy file to master, user comments not deletion, keep ubuntu live usb/cd handy for emergency editing....
|
Before I forget, my grub 1st menu has a few extra lines haveing coming from repeated tries. What is the way to remove them.
A new install from disk didn't help anything. I guess sonic that you are right. No matter what I typed to get gedit the grub menu, gtk gave me a warning display could not be opened. I wasn't going to alter it, just check out the command and look at it. I don't know why it said display though. This system has two HDs but I am sure it wouldnt be to easy to boot from the second one. About the only way I know at this time would be go into cmos and change the boot order. I think there is an option to make the second drive boot 1st after cd and floppy. Stupid spellchecker isn't working right. No options show to ignore etc. I always check it myself anyways. |
All times are GMT -5. The time now is 08:43 AM. |