Problems with Ensoniq ES1371
 

I have an Ensoniq ES1371 sound card which works only intermitantly. On rare occasions it's detected while booting and works fine, but other times the module doesn't load (lsmod doesn't show it), so obviously, it doesn't work. I've tried inserting the module manually and it gives me the following errors:

root@Magrathea:~# insmod es1371.o
es1371.o: unresolved symbol gameport_register_port
es1371.o: unresolved symbol ac97_probe_codec
es1371.o: unresolved symbol ac97_alloc_codec
es1371.o: unresolved symbol gameport_unregister_port
es1371.o: unresolved symbol ac97_release_codec

Can anyone help me or suggest what I should do?

I'm using Slackware 9.1, kernel 2.4.22

I should also add that alsaconf detects NO PCI or PnP soundcards.... but the Ensonic card is in /proc/pci

(from /proc/pci)

Bus 1, device 7, function 0:
Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 6).
IRQ 3.
Master Capable. Latency=64. Min Gnt=12.Max Lat=128.
I/O at 0xdf00 [0xdf3f].

About the best advice I can give you is to open a term as root and type dmesg and copy the contents of your printout here and someone might be able to step in and help you out. I use the same card and have never had a problem always worked with every distro right out the box. Could it be a hardware problem?

It's quite possibly a hardware problem. I looked through the output from dmesg and saw no reference to the soundcard at all, but i'll post it anyway.

root@Magrathea:~# dmesg
Linux version 2.4.22 (root@midas) (gcc version 3.2.3) #6 Tue Sep 2 17:43:01 PDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017ec0000 (usable)
BIOS-e820: 0000000017ec0000 - 0000000017ef8000 (ACPI data)
BIOS-e820: 0000000017ef8000 - 0000000017f00000 (ACPI NVS)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
382MB LOWMEM available.
On node 0 totalpages: 97984
zone(0): 4096 pages.
zone(1): 93888 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda6
Initializing CPU#0
Detected 730.969 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1458.17 BogoMIPS
Memory: 384500k/391936k available (1813k kernel code, 7048k reserved, 614k data, 116k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfda95, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Transparent bridge - Intel Corp. 82801AA PCI Bridge
PCI: Using IRQ router PIIX [8086/2410] at 00:1f.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH: IDE controller at PCI slot 00:1f.1
ICH: chipset revision 2
ICH: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM FIREBALLP LM30.0, ATA DISK drive
blk: queue c03a9d80, I/O limit 4095Mb (mask 0xffffffff)
hdc: LG CD-RW CED-8080B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=3649/255/63, UDMA(66)
hdc: attached ide-cdrom driver.
hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 1210.000 MB/sec
32regs : 725.600 MB/sec
pIII_sse : 1498.800 MB/sec
pII_mmx : 1640.000 MB/sec
p5_mmx : 1711.200 MB/sec
raid5: using function: pIII_sse (1498.800 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 116k freed
Adding Swap: 714852k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 320M
agpgart: Detected an Intel i810 E Chipset.
agpgart: detected 4MB dedicated video ram.
agpgart: AGP aperture is 64M @ 0xf8000000
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
PCI: Found IRQ 10 for device 01:01.0
PCI: Sharing IRQ 10 with 00:1f.2
eth0: Intel Corp. 82557/8/9 [Ethernet Pro 100], 00:D0:B7:C6:DD:70, IRQ 10.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 10 for device 00:1f.2
PCI: Sharing IRQ 10 with 01:01.0
PCI: Setting latency timer of device 00:1f.2 to 64
uhci.c: USB UHCI at I/O 0xef80, IRQ 10
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
i810_rng hardware driver 0.9.8 loaded
hub.c: new USB device 00:1f.2-2, assigned address 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00e) is not claimed by any active driver.
usb.c: registered new driver usbmouse
input0: Logitech USB-PS/2 Optical Mouse on usb1:2.0
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
memory : d384a1b0
memory : d384a1f0
memory : d384a230
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid command operation code -- (asc=0x20, ascq=0x00)
The failed "Get Configuration" packet command was:
"46 02 00 1e 00 00 00 00 08 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read Table of Contents" packet command was:
"43 00 05 00 00 00 00 00 04 00 00 00 "

Hi, have you recently recompile your kernel? I had this problem after I recompiled my kernel, and the solution I used was to compile sound support as a module, but don't compile OSS built in, I just didn't compile OSS.

Once you've disabled OSS, and made Sound as a module, you should recompile and then recompile your modules too. Then recompile the alsa-drivers and then run alsaconf or modprobe them manually.

Hope that helps.