ATI Driver Slackware 11.0 - StartX yields Xorg Version mismatch
 

hi all,

well I got the 11.0 installed.

i went with huge26 as i know that on 10.2 that kernel worked for me and gave me good DRI.

that said I followed the same procedure that I did on 10.2; I get successful building of the modules, and the initial loading of the module. However, from init3 typing startx gives me:

xversion mismatch
detected x.org 7.0.0.0 required x.org.6.8.0.0
failed to load module
module requirement mismatch

now I'm using ati's fglrx_6_8_0-8.29.6-1.i386

i simply downloaded the rpm and used rpm2tgz

then installpkg
then cd /lib/modules/fglrx/buildmod
then sh ./make.sh
then went to /lib/modules/fglrx and ran sh ./make_install.sh

again the module builds and I get success.

i also created in my fstab:
tmpfs /dev/shm tmpfs defaults 0 0

it was mounted and verified with 'mount | grep "shm"' in console

i removed it all, threw in the x11 radeon patch and still no luck after going thru the install process.

i then removed all x11 stuff and the ati patch, reinstalled the stock xorg's rebooted again, tried the ati 32bit installer and got a failure with that too.

am I doing something wrong here?

also I noticed that there is no "Section dri" "mode 0666" in xorg file...do we still use that I put it in.

I do have "glx" and "dri" modules in my xorg.conf

I added the section dri there too. the glx and dri are un-commented.

You need the driver module for xorg 6.9 and higher. Xorg 6.9 and higher must use the "run" package not the rpm. The rpm you downloaded is for xorg 6.8 only. Just download the 55mb ATI installer and run it with "sh".

I don't get it...I ran this b4 and it faile and now it works :D

Now I still have a problem tho :(

As root in KDE...(yea i know) in konsole..glxgears runs fine, no error's. GLXINFO reports DRI yes.

Now as normal user, fogie...glxinfo reports yes for dri, glxgears and fgl_glxgears -fbo
echo this over and over on the screen:
This is at the bottom of my xorg:
Section "DRI"
Mode 0666
EndSection

Any idea why I get dri as a user...but permission errors when actually using the dri? is that what this patch that Pat issued is for?

Check to make sure if you have /dev/shm mounted with the correct permission to read and write to it. As root, issue a "chmod 777 /dev/shm" to get the correct permission.

omg..........

I think?? but not sure, I did not enter a "carriage return" or hit enter for you younger folks :D after my /dev/shm line in my fstab.

interestingly enuff, I did not get the "no final newline error" in my boot process.

but I made that changed rebooted, and now all is well.

but I think the chmod 777 may be useful, i see many threads with this error of shared memory. i'll make a note of it in case i get the errors again.

Now off to figure out why my fstab is giving me errors for the fat32 partition I have, wierd :(

btw stafz32 I forgot to say thank you :D

I try to keep two blank lines at the bottom of my /etc/fstab just to be sure that if I add a line in a rush it will always work!

Currently waiting for newer drivers to download, upgraded to Slack11 this weekend after a repartition and suddenly found that my ATI drivers don't like Xorg6.8!

Ah... now downloaded, but, at 1280x1024 I get:

Which is hardly earth shattering, especially for a P4 3.0GHz (although there is no increase in CPU load while running glxgears, so at least that's right)!

I have DRI enabled though:

And in /etc/fstab:

In xorg.conf

So everything looks right...

System info:

And the card is a Radeon X300SE

If anyone can give me some ideas for how to up the performance they'd be most welcome!

For what it's worth...

I have installed the ATI drivers (Slackware 11.0, kernel 2.6.18, Pentium 4 @ 3GHz, 1G RAM). Before installing the ATI drivers, I built xorg.conf with xorgconfig (so that's what was in /etc/X11), then rebuilt it with aticonfig (which merges with the existing xorg.conf and adds ATI-specific variables). Things that appear to matter at the manufacturer and model name of the display and the horizontal and vertical sync ranges. The graphic card is an ATI X300 series (don't know if there is some letter appended to the end of that, but I don't think it really matters).

Hope this helps some.

Running glxgears with the settings below yields:

glxgears
1310 frames in 5.0 seconds = 261.933 FPS
1334 frames in 5.0 seconds = 266.636 FPS
982 frames in 5.0 seconds = 196.248 FPS
1173 frames in 5.0 seconds = 234.414 FPS
1240 frames in 5.0 seconds = 247.812 FPS

Running fgl_glxgears yields:

fgl_glxgears
Using GLX_SGIX_pbuffer
882 frames in 5.0 seconds = 176.400 FPS
1098 frames in 5.0 seconds = 219.600 FPS
1090 frames in 5.0 seconds = 218.000 FPS
1114 frames in 5.0 seconds = 222.800 FPS
1090 frames in 5.0 seconds = 218.000 FPS

These are the relevant settings in xorg.conf; the Module section:

Section "Module"
Load "glx"
Load "extmod"
Load "xtrap"
Load "record"
Load "dbe"
Load "dri"
Load "freetype"
Load "type1"
EndSection

The Monitor section:

Section "Monitor"
Identifier "aticonfig-Monitor[0]"
Option "VendorName" "ATI Proprietary Driver"
#Option "ModelName" "Generic Autodetecting Monitor"
Option "ModelName" "SyncMaster"
HorizSync 30.0 - 85.0
VertRefresh 50.0 - 160.0
Option "DPMS" "true"
EndSection

The Device section:

Section "Device"
Identifier "Card0"
Driver "ati"
VendorName "ATI Technologies Inc"
BoardName "RV370 5B60 [Radeon X300 (PCIE)]"
BusID "PCI:1:0:0"
EndSection

Section "Device"
Identifier "aticonfig-Device[0]"
Driver "fglrx"
EndSection

And the Screen section:

Section "Screen"
Identifier "aticonfig-Screen[0]"
Device "aticonfig-Device[0]"
Monitor "aticonfig-Monitor[0]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1600x1200" "1280x1024"
EndSubSection
EndSection

The DRI section:

Section "DRI"
Mode 0666
EndSection

Yes, conveniently aticonfig left my xorg.conf corrupt by putting random "0"s in the file, the only things that it seemed to do was rename my screen, monitor and device sections (while ignoring all the settings that I needed, such as resolutions, Hsync, Vsync and bit-depth) plus it stuck in the device line for:

Starting X then failed due to (from memory):

So I copied the device line into a known good xorg.conf (generated by "xorgconfig" and tried that instead. Commenting out Section "DRI" leaves me with a whopping 11FPS at full screen, so it's doing something!

(I'll run aticonfig and then start X when I get home and post in the actual errors since this may help someone else...)