Hi Everyone,
I am new to this forum and to the wireless connection. I need a help to connect to internet through Telit LE910-nag and AT&T 4g/LT Go Phone SIM Card. Our device uses Ubutun 14.04.
I tried to use wvdial to make the connection, but failed. Here is the code in my conf file:
[Dialer AT_N_T]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = AT+CGDCONT=1,"IP","Broadband",
Stupid Mode = 1
ISDN = 0
Modem Type = USB Modem
New PPPD = yes
Phone = *99***1#
Modem = /dev/ttyUSB2[/SIZE][/FONT]
Username = 1
Password = 1
Baud = 9600
Here is the message on console when I run "wvdial AT_N_T":
--> WvDial: Internet dialer version 1.61
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Sending: AT+CGDCONT=1,"IP","Broadband",
AT+CGDCONT=1,"IP","Broadband",
OK
--> Modem initialized.
--> Sending: ATDT*99***1#
--> Waiting for carrier.
ATDT*99***1#
CONNECT 100000000
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Wed Aug 24 18:13:21 2016
--> Pid of pppd: 3386
--> pppd: ?U? @L? ?W?
--> Using interface ppp0
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> Authentication (PAP) started
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> Authentication (PAP) successful
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> pppd: ?U? @L? ?W?
--> Terminate Request (Message: "No network protocols running" )
--> pppd: ?U? @L? ?W?
--> Terminate Request (Message: "No network protocols running" )
Here is the message in log:
pppd 2.4.5 started by root, uid 0
pppd[3386]: using channel 1
pppd[3386]: Using interface ppp0
pppd[3386]: Connect: ppp0 <--> /dev/ttyUSB2
pppd[3386]: sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xe9f2ef3e> <accomp>]
pppd[3386]: rcvd [LCP ConfReq id=0x0 <asyncmap 0x0> <auth pap> <magic 0x45e46bbd> <pcomp> <accomp>]
pppd[3386]: sent [LCP ConfRej id=0x0 <pcomp>]
pppd[3386]: rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0xe9f2ef3e> <accomp>]
pppd[3386]: rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <auth pap> <magic 0x45e46bbd> <accomp>]
pppd[3386]: sent [LCP ConfAck id=0x1 <asyncmap 0x0> <auth pap> <magic 0x45e46bbd> <accomp>]
pppd[3386]: sent [LCP EchoReq id=0x0 magic=0xe9f2ef3e]
pppd[3386]: sent [PAP AuthReq id=0x1 user="1" password=<hidden>]
pppd[3386]: rcvd [LCP DiscReq id=0x2 magic=0x45e46bbd]
pppd[3386]: rcvd [LCP EchoRep id=0x0 magic=0x45e46bbd e9 f2 ef 3e]
pppd[3386]: rcvd [PAP AuthAck id=0x1 ""]
pppd[3386]: PAP authentication succeeded
pppd[3386]: sent [CCP ConfReq id=0x1 <bsd v1 15>]
pppd[3386]: sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
kernel: [14163.604627] PPP BSD Compression module registered
pppd[3386]: rcvd [LCP ProtRej id=0x3 80 fd 01 01 00 07 15 03 2f]
pppd[3386]: Protocol-Reject for 'Compression Control Protocol' (0x80fd) received
pppd[3386]: sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
pppd[3386]: message repeated 8 times: [ sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]]
pppd[3386]: sent [LCP EchoReq id=0x1 magic=0xe9f2ef3e]
pppd[3386]: IPCP: timeout sending Config-Requests
pppd[3386]: sent [LCP TermReq id=0x2 "No network protocols running"]
pppd[3386]: sent [LCP TermReq id=0x3 "No network protocols running"]
pppd[3386]: Connection terminated.
pppd[3386]: Modem hangup
I have been pork around on this last three days. I tried to get helps from AT&T technical support, and didn't make any progress. I am contacting Telit technical support too. I hope that some experts here can point me to a correct direction. Thank you!
Meliza
