| kalkulus |
10-07-2005 05:42 PM |
NEC ND-3540a problem burning CD-RW
when I try to burn cd-rw that I erased just a minut ago k3b reports input/output errors and after that it won't read CDs any more. it reads DVDs just fine. I tried it on two drives with the same CD-RW and they both stopped reading CDs. can it be the bad CD-RW? I've never heard of bad disk destroying the drive
I'm using Slackware 10.2, kernel is 2.4.31. no scsi emulation, but cdrecord uses dev=ATAPI:0,0,0 option
here's the debug data
Code:
System
-----------------------
K3b Version: 0.12
KDE Version: 3.4.2
QT Version: 3.3.4
Kernel: 2.4.31
Devices
-----------------------
_NEC DVD_RW ND-3540A 1.01 (/dev/hdc, ) at /cdrom [CD-R; CD-RW; CD-ROM; DVD-ROM; DVD-R; DVD-RW; DVD-R DL; DVD+R; DVD+RW; DVD+R DL] [DVD-ROM; DVD-R Sequential; DVD-R Dual Layer Sequential; DVD-RW Restricted Overwrite; DVD-RW Sequential; DVD+RW; DVD+R; DVD+R Double Layer; CD-ROM; CD-R; CD-RW] [SAO; TAO; RAW; SAO/R96R; RAW/R96R; Restricted Overwrite]
Used versions
-----------------------
cdrecord: 2.1
cdrecord
-----------------------
scsidev: 'ATAPI:/dev/hdc'
devname: 'ATAPI:/dev/hdc'
scsibus: -2 target: -2 lun: -2
Warning: Using ATA Packet interface.
Warning: The related Linux kernel interface code seems to be unmaintained.
Warning: There is absolutely NO DMA, operations thus are slow.
SCSI buffer size: 64512
/usr/bin/cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code.
/usr/bin/cdrecord: If you need DVD-R/DVD-RW support, ask the Author for cdrecord-ProDVD.
/usr/bin/cdrecord: Free test versions and free keys for personal use are at THE_FORUM_COMPLAINS_ABOUT_THE_URL
Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.8'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : '_NEC '
Identifikation : 'DVD_RW ND-3540A '
Revision : '1.01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A
Profile: 0x002B
Profile: 0x001B
Profile: 0x001A
Profile: 0x0015
Profile: 0x0014
Profile: 0x0013
Profile: 0x0011
Profile: 0x0010
Profile: 0x000A (current)
Profile: 0x0009
Profile: 0x0008 (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1343488 = 1312 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 637 MB
Total size: 732 MB (72:33.22) = 326492 sectors
Lout start: 732 MB (72:35/17) = 326492 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 2
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11077 (97:34/23)
ATIP start of lead out: 359849 (79:59/74)
1T speed low: 4 1T speed high: 10
2T speed low: 2 2T speed high: 10
power mult factor: 2 6
recommended erase/write power: 5
A1 values: 24 2C DC
A2 values: 14 A4 4A
A3 values: 04 C4 80
Disk type: Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 33357
Starting to write CD/DVD at speed 10 in real SAO mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Turning BURN-Free on
Performing OPC...
Sending CUE sheet...
/usr/bin/cdrecord: WARNING: Drive returns wrong startsec (0) using -150
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 637 MB written.
/usr/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 01 F0 00 00 1F 00
status: 0x0 (GOOD STATUS)
cmd finished after 10.104s timeout 200s
/usr/bin/cdrecord: A write error occured.
/usr/bin/cdrecord: Please properly read the error message above.
/usr/bin/cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable error
CDB: 00 00 00 00 00 00
status: 0xa (Reserved)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 80 D0 36
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x04 Qual 0x01 (logical unit is in process of becoming ready) Fru 0x0
Sense flags: Blk 0 (not valid) operation 81% done
cmd finished after 22.060s timeout 200s
/usr/bin/cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable error
CDB: 00 00 00 00 00 00
status: 0xa (Reserved)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 80 FF FF
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x04 Qual 0x01 (logical unit is in process of becoming ready) Fru 0x0
Sense flags: Blk 0 (not valid) operation 99% done
cmd finished after 22.170s timeout 200s
write track data: error after 1015808 bytes
Writing time: 72.639s
Average write speed 72.3x.
Fixating...
/usr/bin/cdrecord: Input/output error. flush cache: scsi sendcmd: retryable error
CDB: 35 00 00 00 00 00 00 00 00 00
status: 0xa (Reserved)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 00 00 80 FF FF
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0
Sense flags: Blk 0 (not valid) operation 99% done
cmd finished after 2.000s timeout 200s
/usr/bin/cdrecord: Caught interrupt.
Trouble flushing the cache
BURN-Free was never needed.
/usr/bin/cdrecord: fifo had 80 puts and 17 gets.
/usr/bin/cdrecord: fifo was 0 times empty and 5 times full, min fill was 95%.
cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=ATAPI:/dev/hdc speed=10 -dao driveropts=burnfree -eject -data /d/Temp/slackware.10.2_1.iso
dmesg
Code:
Linux version 2.4.31 (root@meanX) (gcc version 3.3.6) #4 Thu Oct 6 20:35:07 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 KT400A ) @ 0x000f71d0
ACPI: RSDT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7fc0
ACPI: DSDT (v001 KT400A AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Kernel command line: BOOT_IMAGE=Linux-novi ro root=302
Initializing CPU#0
Detected 1533.211 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3060.53 BogoMIPS
Memory: 515464k/524224k available (1740k kernel code, 8372k reserved, 592k data, 108k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP 1800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Level Trigger.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xfbae0, last bus=1
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
BIOS EDD facility v0.11 2004-Jun-21, 2 devices found
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
Detected PS/2 Mouse Port.
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:0f.0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.0
ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio
hda: WDC WD2000JB-00GVA0, ATA DISK drive
hdb: QUANTUM FIREBALLlct20 30, ATA DISK drive
blk: queue c0391e60, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0391f9c, I/O limit 4095Mb (mask 0xffffffff)
hdc: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 390721968 sectors (200050 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 58633344 sectors (30020 MB) w/418KiB Cache, CHS=3649/255/63
hdc: attached ide-cdrom driver.
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 >
hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 >
Via 686a/8233/8235 audio driver 1.9.1-ac3
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 00:11.5 to 64
ac97_codec: AC97 codec, id: ALG96 (Unknown)
via82cxxx: Codec rate locked at 48Khz
via82cxxx: board #1 at 0xBC00, IRQ 11
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 108k freed
Adding Swap: 514072k swap-space (priority -1)
Adding Swap: 208804k swap-space (priority -2)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver v1.1.22 [Flags: R/O MODULE]
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,66), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul 27 07:55:38 PDT 2004
via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker
ANOTHER_URL
eth0: VIA VT6102 Rhine-II at 0xc000, 00:04:61:61:7e:c4, IRQ 11.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
ehci_hcd 00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 00:10.4: irq 11, pci mem e0d05000
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb-uhci.c: $Revision: 1.275 $ time 20:28:28 Oct 6 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xac00, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb800, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 5
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 288 bytes per conntrack
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
PPP BSD Compression module registered
PPP Deflate Compression module registered
spurious 8259A interrupt: IRQ7.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
PPP BSD Compression module registered
PPP Deflate Compression module registered
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Cannot read medium - incompatible format -- (asc=0x30, ascq=0x02)
The failed "Send DVD Structure" packet command was:
"ad 00 00 00 00 00 00 00 00 20 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
Error in command data byte 12
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
Error in command data byte 12
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
Error in command data byte 12
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid command operation code -- (asc=0x20, ascq=0x00)
The failed "<NULL>" packet command was:
"3c 00 00 00 00 00 00 00 04 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 10 00 00 00 "
Error in command data byte 7
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Cannot read medium - incompatible format -- (asc=0x30, ascq=0x02)
The failed "Send DVD Structure" packet command was:
"ad 00 00 00 00 00 00 00 00 20 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
Error in command data byte 12
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
Error in command data byte 12
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
Error in command data byte 12
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid command operation code -- (asc=0x20, ascq=0x00)
The failed "<NULL>" packet command was:
"3c 00 00 00 00 00 00 00 04 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
hdc: irq timeout: status=0xd0 { Busy }
hdc: irq timeout: error=0xd0LastFailedSense 0x0d
hdc: DMA disabled
hdc: ATAPI reset complete
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 10 00 00 00 "
Error in command data byte 7
cdrom: open failed.
lspci -v, the relevant data
Code:
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80)
Subsystem: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
Flags: bus master, 66Mhz, medium devsel, latency 8
Memory at e8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [80] AGP version 3.5
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: ec000000-edffffff
Prefetchable memory behind bridge: e0000000-e7ffffff
Capabilities: [80] Power Management version 2
00:0f.0 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at a800 [size=16]
Capabilities: [c0] Power Management version 2
|
