Slackware & GSB
 

Hi folks

im new slacker and i have Question about slackware + gnome build slack(gsb)

im make new install and did not Choose kde pkg

after install complete the slackware run xinitrc.twn and it is

very basic (runlevel3)

http://img14.imageshack.us/img14/5217/screenshot48i.png

after that im use this link

lynx --source http://gnomeslackbuild.org/net-install | bash


it is install slapt-get and gnome

it this good way to install ??

or i must choose another way ??

need advice please

thanks

never done it but looks like it's the reccomended for slackware-13.1 (32bit).

they point to the README for more details.

i tried this way and all was ok,but i remember GSB remove 2 packages from SW
so i decide after to move to XFCE

i did not remove any pkg
just did not pack kde whene im install slackware after that install GSB

GSB work fine with you ????

---------- Post added 01-28-11 at 01:12 PM ----------

thanks dude
my english is not good
can you give me easy steps hear to install it ?

yes,work fine,no problem

All I did was run 'lynx --source http://gnomeslackbuild.org/net-install | bash' and it installed, then I could run xwmconfig to set GNOME as the default WM/DE.

sorry,the packages are not removed,are replaced
http://ftp.osuosl.org/pub/gsb/gsb-2....D_PACKAGES.TXT

did you run this from kde or xinitrc.twn (runlevel3) ?

and did the sound work ?

the pkg replaced automatic or manually ؟

automatic,this way is called "Automated net installation"

did you run lynx --source http://gnomeslackbuild.org/net-install | bash from kde or xinitrc.twn (runlevel3) ?

and did the sound work ?

need your help to complete install gsb

from console (runlevel 3)
when u have sound in slackware then must work in GSB to

runlevel 3 like this ? http://img14.imageshack.us/img14/5217/screenshot48i.png

and this is my way to install gsb i found it in in this topic

http://www.linuxac.org/forum/showthr...CC%E5%C9-Gnome

please see it and tell me my way to install good or bad ?

this is an english speaking forum: I can't understand (and like me I think many others) what's written in the link above.

which problem do you find following the suggested procedure with lynx? have you tried it?

sorry dude

my way to install GSB is that
new slackware install
did not choose kde and complete install
after reboot the slackware run with xinitrc.twn
after that im use lynx --source http://gnomeslackbuild.org/net-install | bash
after it is finsh make chmod to

$ chmod +x /etc/rc.d/rc.avahidaemon
$ chmod +x /etc/rc.d/rc.avahidnsconfd
-------
$ . /etc/rc.d/rc.avahidaemon start
$ . /etc/rc.d/rc.avahidnsconfd start
------------
export XDG_CONFIG_DIRS=/etc/xdg:/etc/gnome/xdg
---------
$ ./rc.messagebus restart
---------
$ chmod +x rc.networkmanager
---------
$ ./rc.networkmanager start
-----------
after that im enable GDM on system boot, and edit
/etc/inittab and change the default run level from 3 to 4.

# Default runlevel. (Do not set to 0 or 6)
id:4:initdefault:
--------
and $ chmod +x /etc/rc.d/rc.cups

and xwmconfig and choose gnome

and reboot

is that good way or bad ??