LinuxQuestions.org - HP notebook and Slackware-current: temperature seems a bit high

- Slackware (https://www.linuxquestions.org/questions/slackware-14/)

- - HP notebook and Slackware-current: temperature seems a bit high (https://www.linuxquestions.org/questions/slackware-14/hp-notebook-and-slackware-current-temperature-seems-a-bit-high-701316/)

HP notebook and Slackware-current: temperature seems a bit high [SOLVED]

Hi all,

As of late I've been "feeling" my HP Dv6663's temperature quite high. Slackware's installed from stock (no kernel recompiling) and I've upgraded to -current.

Code:

root@predator:~# uname -a

Linux predator 2.6.27.7-smp #2 SMP Thu Nov 20 22:32:43 CST 2008 i686 Intel(R) Core(TM)2 Duo CPU    T7500  @ 2.20GHz GenuineIntel GNU/Linux

I know these processors dissipate a lot of heat, here's cpuinfo:

Code:

root@predator:~# cat /proc/cpuinfo

processor      : 0

vendor_id      : GenuineIntel

cpu family      : 6

model          : 15

model name      : Intel(R) Core(TM)2 Duo CPU    T7500  @ 2.20GHz

stepping        : 11

cpu MHz        : 2194.705

cache size      : 4096 KB

physical id    : 0

siblings        : 2

core id        : 0

cpu cores      : 2

apicid          : 0

initial apicid  : 0

fdiv_bug        : no

hlt_bug        : no

f00f_bug        : no

coma_bug        : no

fpu            : yes

fpu_exception  : yes

cpuid level    : 10

wp              : yes

flags          : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm ida

bogomips        : 4389.41

clflush size    : 64

power management:



processor      : 1

vendor_id      : GenuineIntel

cpu family      : 6

model          : 15

model name      : Intel(R) Core(TM)2 Duo CPU    T7500  @ 2.20GHz

stepping        : 11

cpu MHz        : 2194.705

cache size      : 4096 KB

physical id    : 0

siblings        : 2

core id        : 1

cpu cores      : 2

apicid          : 1

initial apicid  : 1

fdiv_bug        : no

hlt_bug        : no

f00f_bug        : no

coma_bug        : no

fpu            : yes

fpu_exception  : yes

cpuid level    : 10

wp              : yes

flags          : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm ida

bogomips        : 4389.42

clflush size    : 64

power management:

Also there seems to be nothing installed under:

Code:

root@predator:~# ls /proc/acpi/thermal_zone/

root@predator:~#

A while ago, when I first started messing around with Slackware, next of performing a full installation, I would recompile kernel to strip it of any unnecessary module. Then I read somewhere it doesn't make much of a difference and just gave up compiling kernel. Now I seem to be in need of it again... or not?

Any ideas and help will be greatly appreciated!

Thanks in advance!

Hi

since no-one has replied let me start the ball rolling

You appear to have a portable

I suggest you install lm-sensors...you can also INSTALL the front end gkrellm
run

Code:

sensors-detect

with root powers to check what chips you have on your motherboard.

2) try

Code:

cat /proc/acpi/thermal_zone/THRM/temperature

3) as its a lappy I suggest you move off an hog like KDE gnome and move to a minimal wm like LXDE fluxbox openbox etc

you could also check if you could use smaller apps in liew of Open office? etc

aus9,

Thanks for the reply! I have followed your lead and installed lm_sensors-3.0.3 and Gkrellm.

As root I typed sensors-detect and it detected a Intel Core family thermal sensor (driver 'coretemp') and it said I should add the following lines to /etc/rc.d/rc.local:

Code:

# Chip drivers

modprobe coretemp

/usr/bin/sensors -s

After

Code:

# /etc/rc.d/rc.local restart

I restarted gkrellm, went configurations and ... voilá! there where options to monitor both CPUs temperatures. CPU core temps have mantained at 55 ~ 56 degrees Celsius.

Now I'm off looking for some extra plugins.

I still haven't found anything under /proc/acpi/thermal_zone, as you may see here, or below, on the attached thumbnails.

My system is, indeed a laptop, and I couldn't get used to "lighter" WM like XFCE, mainly because I think it is too similar to Gnome - which I really tried (more than once!) and did not liked. Also since I didn't like KDE 4.x, I still run KDE 3.5.x. But I think I'll give LXDE a try.

Again I thank your help!

Gustavo

hi

can't see the first image but can see your attachment.

ok try

Code:

su

/etc/init.d/acpid restart

2) you may need to check your motherboard manual and cpu.

not all boards have sensors
some have sensors for fans but not temps

Your bios is the best place to look first...if you can see temps and fan speeds you should get there.

aus9,

I checked BIOS and have not found temps or fan speeds. Also I can only make gkrellm list core temps after I restart (as root) /etc/rc.d/rc.local. This file does not loads on boot depite being on /etc/rc.d and is executable (chmod +x), but this is another issue.

So I restart rc.local and on gkrellm I go Configurations > Builtins > Sensors > Temperatures and check coretemp@0/temp1 and coretemp@1/temp1, see attached image.

Then gkrellm shows CPU's core temps, but still no fan speed. Going through the notebook's manual I found that there is a fan mounted on the processor.

Finally something that's bugging me is that there is nothing under /proc/acpi/thermal_zone.

Gustavo

Check with lsmod if module thermal is loaded. If not, load it with modprobe.

Also, are you using cpu frequency scaling? It is quite important for laptops. Load acpi-cpufreq and cpufreq-ondemand modules (you should uncomment those in /etc/rc.d/rc.modules). Then install cpufrequtils or add next lines to /etc/rc.d/rc.local :

Code:

echo "ondemand" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor

echo "ondemand" > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor

You have some other governors like performance, powersave etc. I am using laptop(s) as my only system for last 2 and half years, and ondemand governor is probably the best choice. Personally, I think that temperature variations between 45 and 60 C are quite normal for the most time, even higher (arround 70 C) when it is loaded.

kukibl,

Thanks for your insights too!

I had already edited /etc/rc.d/rc.modules and uncommented the lines to enable thermal, acpi-cpufreq and cpufreq-ondemand.

Now I installed cpufrequtils I downloaded from SlackBuild.org, and it offered two news commands: cpufreq-info and cpufreq-set. I checked and cpufreq-info gave me this:

Code:

root@predator:~# cpufreq-info

cpufrequtils 005: cpufreq-info (C) Dominik Brodowski 2004-2006

Report errors and bugs to cpufreq@vger.kernel.org, please.

analyzing CPU 0:

  driver: acpi-cpufreq

  CPUs which need to switch frequency at the same time: 0 1

  hardware limits: 800 MHz - 2.20 GHz

  available frequency steps: 2.20 GHz, 2.20 GHz, 1.60 GHz, 1.20 GHz, 800 MHz

  available cpufreq governors: ondemand, userspace

  current policy: frequency should be within 800 MHz and 2.20 GHz.

                  The governor "ondemand" may decide which speed to use

                  within this range.

  current CPU frequency is 800 MHz (asserted by call to hardware).

analyzing CPU 1:

  driver: acpi-cpufreq

  CPUs which need to switch frequency at the same time: 0 1

  hardware limits: 800 MHz - 2.20 GHz

  available frequency steps: 2.20 GHz, 2.20 GHz, 1.60 GHz, 1.20 GHz, 800 MHz

  available cpufreq governors: ondemand, userspace

  current policy: frequency should be within 800 MHz and 2.20 GHz.

                  The governor "ondemand" may decide which speed to use

                  within this range.

  current CPU frequency is 800 MHz (asserted by call to hardware).

root@predator:~#

I imagined what cpufreq-set might do, so I tried # cpufreq-set --help, which returned what I expected and decided not to play with it!

So I figure all is good here! At the moment, gkrellm is showing both CPUs to be under 45 C, as you can see on the attached image.

I guess now I need a plugin for gkrellm monitor my processor fan.

Off digging one!

Thanks so far,

Gustavo

In general, I don't use cpufrequtils, I prefer manual way (I gave you an example in my previous post).

Anyway, for general use, cpufreq-set is quite easy:

Code:

#cpufreq-set -c[core number] -g[name of the governor]

In your case, you would do like this:

Code:

#cpufreq-set -c 0 -g ondemand

#cpufreq-set -c 1 -g ondemand

For advanced use (min. and max. freqs) consult man and help pages.

kukibl,

I just added the lines to /etc/rc.d/rc.local:

Code:

echo "ondemand" > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor

echo "ondemand" > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor

I'm just a little worried that rc.local do not seems to be loaded at startup. So I may have to use cpufrequtils, that seems to be a more permanent solution, right?

Thanks so far,

Gustavo

I am not sure if cpufrequtils are more permanent solution. As I wrote, I don't use them. You should check if there is rc.cpufreq in /etc/rc.d (since you installed cpufrequtils from SlackBuilds) and make it executable.

I saw you started new thread concerning rc.local problem. It should work, unless you did some modifications to /etc/rc.d/rc.M file or permissions. Check ones again if rc.local has executable permission and is everything all right in rc.M file (find line that is concerning rc.local). Also, maybe you should write command with full path. For example: /sbin/cp some-file some-other-file.

hi
In addition
I forgot to mention there is a tweak file called /etc/sensors.conf

Also when running sensors-detect with root powers .....hopefully you get to a line or 2 to put in
/etc/modules
and I think you need to type yes (in full rather than y)?

kukibl,

I'm not using cpufreq-set, but from time to time I check CPUs frequency with cpufreq-info. When idle CPU frequencies are 800MHz and core temps vary 35 ~ 45 C. When compiling (a big package, say wine) CPU frequencies jump to 2.20GHz and core temps escalate to 50 ~ 60 C. And I'm pretty satisfied with this! However, I found no /etc/rc.d/rc.cpufreq.

I managed to solve the /etc/rc.d/rc.local issue as well, writing the command with full path name, replacing the "." for "/bin/sh" when starting some services and calling rc.local at /etc/rc.d/rc.M.

aus9,

After running

Code:

# sensors-detect

I got the following two lines to put in /etc/rc.d/rc.local

Code:

modprobe coretemp

/usr/bin/sensors -s

Again thanks for taking the time to help me out!

Cheers,
Gustavo