LinuxQuestions.org - How to fix this USB mouse with scroll

I am just switch my serial mouse to USB mouse. But just can get the mouse works..below is my dmesg.

Code:

usb.c: registered new driver usbdevfs

usb.c: registered new driver hub

usb-uhci.c: $Revision: 1.259 $ time 15:45:26 Jun 23 2001

usb-uhci.c: High bandwidth mode enabled

usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 10

usb-uhci.c: Detected 2 ports

usb.c: new USB bus registered, assigned bus number 1

hub.c: USB hub found

hub.c: 2 ports detected

usb-uhci.c: v1.251 Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber

usb-uhci.c: USB Universal Host Controller Interface driver

usb.c: registered new driver usb_mouse

usbmouse.c: v1.6 Vojtech Pavlik <vojtech@suse.cz>

usbmouse.c: USB HID Boot Protocol mouse driver

PCI: Found IRQ 12 for device 00:0c.0

PCI: The same IRQ used for device 00:0a.0

hub.c: USB new device connect on bus1/2, assigned device number 2

input0: A4Tech USB Optical Mouse on usb1:2.0

I do trillion of times mouseconfig and select 'USB connected mouse' but just won't works.
By the way,

Quote:

bash# ls -al /dev/mouse
lrwxrwxrwx 1 root root 12 Nov 3 13:43 /dev/mouse -> input/mouse0

Quote:

bash# ls -al /dev/usb/mouse*
crw-rw---- 1 root root 180, 16 Mar 26 2001 /dev/usb/mouse0
crw-rw---- 1 root root 180, 17 Mar 26 2001 /dev/usb/mouse1
crw-rw---- 1 root root 180, 26 Mar 26 2001 /dev/usb/mouse10
crw-rw---- 1 root root 180, 27 Mar 26 2001 /dev/usb/mouse11
crw-rw---- 1 root root 180, 28 Mar 26 2001 /dev/usb/mouse12
crw-rw---- 1 root root 180, 29 Mar 26 2001 /dev/usb/mouse13
crw-rw---- 1 root root 180, 30 Mar 26 2001 /dev/usb/mouse14
crw-rw---- 1 root root 180, 31 Mar 26 2001 /dev/usb/mouse15
crw-rw---- 1 root root 180, 18 Mar 26 2001 /dev/usb/mouse2
crw-rw---- 1 root root 180, 19 Mar 26 2001 /dev/usb/mouse3
crw-rw---- 1 root root 180, 20 Mar 26 2001 /dev/usb/mouse4
crw-rw---- 1 root root 180, 21 Mar 26 2001 /dev/usb/mouse5
crw-rw---- 1 root root 180, 22 Mar 26 2001 /dev/usb/mouse6
crw-rw---- 1 root root 180, 23 Mar 26 2001 /dev/usb/mouse7
crw-rw---- 1 root root 180, 24 Mar 26 2001 /dev/usb/mouse8
crw-rw---- 1 root root 180, 25 Mar 26 2001 /dev/usb/mouse9

And my gpm is running at boot..with the following script.

Quote:

bash# cat /etc/rc.d/rc.gpm

#!/bin/sh
# Running gpm
echo "Running gpm..."
gpm -m /dev/mouse -t imps2
# There is another way to run GPM, where it acts as a repeater outputting a
# virtual MouseSystems mouse on /dev/gpmdata. This is useful for feeding
# gpm's data to X, especially if you've got a busmouse (in that situation X
# and gpm may not coexist without using a repeater). To try running a GPM
# repeater for X, change the gpm command line to look like this:
# gpm -R msc -m /dev/mouse -t imps2
# Then, make sure that the mouse configuration in your XF86Config file refers
# to the repeater device (/dev/gpmdata) and a MouseSystems mouse type. If you
# edit the file directly, you'll want the lines to look like this (minus the
# comment marks '#' shown here, of course):
#Section "Pointer"
# Protocol "MouseSystems"
# Device "/dev/gpmdata"

How to fix this ?