HEEELPPP.....Slackware Networking:(((
first i`m sorry that my english is fucke up a little...ok...I have instaled Slackware 12.0 on my pc.But i have a little problem i can not install my network:((((i do`nt know how....i`m in a local area network.My local are ip is 213.189.169.145....I really really need your help me on this...so please if anyone can help me:(((
|
Hi,
Then I wouldn't use some of the foul language that you have picked up. You need to look at the LQ rules. It would be nice if you did not bold everything. For your network problem. What errors are you getting? What have you attempted? What kernel version? System information? I would suggest that you look at the next two links; |
Thank you for the well put comment onebuck (mostly for pointing minimal to the forum rules).
As for the network problem, as onebuck stated, what have you tried? You said your local ip address is: 213.189.169.145 Is that the ip address of your computer, or is that the ip of a router you are going through? What do you get if you type 'ifconfig -a' in a terminal window (without the ''s)? Thats a start I suppose. Another thing I have noticed is that if you get an ip address, sometimes DNS servers don't cooperated well with linux. So if you get an IP address, but you still cant go anywhere the DNS server is possibly your problem. In order to fix this I manually edit my /etc/resolv.conf and put 'nameserver 4.2.2.2' at the top of the file. I think this is a good start. More info would be appreciated. DragonM15 |
:(
Quote:
|
Try running `netconfig` as root to configure your network. I am assuming you simply didn't know how to configure it -- if you encounter problems when using netconfig, or if netconfig simply does not produce a working network configuration, please post the output of the following commands as root:
Code:
ifconfig -a |
got dual boot?
an obvious thing that you must have checked i think...If you got dual boot with xp... you could jot down the configs! yeah as T3Slider you run netconfig from the terminal. other possible ways i didnt try but are rather too stupid to me... run an ubuntu livecd as for it will always recognize your settings before hand...
just some rather obvious brainstorms.. boot to XP was how i got my net working. |
oky....i restarted in linux and....did a ifconfig -a.....i got this message:
ifconfig -a Link encap local host LoopBack inet addr: 127.0.0.1 Mask 255.0.0.0 inet6 addr: 1/128 Scoop:Host U1 LoopBack Running NFU:16436 Metric Rxpockets: 0errors:0dropped:0anserws:frame:0 Txpockets: 0errors:0dropped:0anserws:canri 0 Collissions: 0txq Rxbytes :0 (o.o b) Txbytes (0.0 b0 sorry about the writhing but....i had to wrote it on my own:)))....after i tried again the netconfig comand and decidet to try out the DHCP thing also....but the same thing... IPv4 Address. . . . . . . . . . . : 213.189.169.145 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 213.189.169.1 DNS Servers . . . . . . . . . . . : 212.68.193.110 212.68.193.196 DHCP Server . . . . . . . . . . . : 212.68.193.113 i really have no ideea what i can do... System Info: http://www.twenga.co.uk/prices-Pavil...op-PC-244940-0 so if somebody has any ideas i would be pleased....Agai i`m sorry i haven`t sleepe for abou 2 day`s:)))))so my writing is stil bad:)))... |
alright, the problem is that your ethernet card is not being recognized. As t3slider stated you need to do an lspci, see the brand/name of your ethernet card, check your kernel config to see if your ethernet card is set as a module. If it is, then you can run 'modprobe moduleforyourethernetcard' Otherwise you might have to recompile your kernel for support for your ethernet card.
Hope this helps a little, DragonM15 P.S. in order to copy things from a terminal window, select the text, and then go to your firefox window, or text editor and click both mouse buttons at the same time. Or in some cases pressing the middle mouse button works also. This 'pastes' the text your previously selected. |
Quote:
root@slax:~# lspci -vv 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Capabilities: [e0] Vendor Specific Information 00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: fa000000-fcffffff Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- Capabilities: [88] Subsystem: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [a0] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2 Link: Latency L0s <256ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 32, PowerLimit 75.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [100] Virtual Channel Capabilities: [140] Unknown (5) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express Unknown type IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed unknown, Width x0 Capabilities: [100] Virtual Channel Capabilities: [130] Unknown (5) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at ff00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at fe00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at fd00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 17 Region 4: I/O ports at fc00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fde00000-fdefffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [50] Subsystem: Hewlett-Packard Company Unknown device 2a50 00:1f.0 ISA bridge: Intel Corporation 82801GH (ICH7DH) LPC Interface Bridge (rev 01) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [e0] Vendor Specific Information 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at fb00 [size=16] 00:1f.2 RAID bus controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA RAID Controller (rev 01) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at fa00 [size=8] Region 1: I/O ports at f900 [size=4] Region 2: I/O ports at f800 [size=8] Region 3: I/O ports at f700 [size=4] Region 4: I/O ports at f600 [size=16] Region 5: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 0500 [size=32] 01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7500 LE] (rev a1) (prog-if 00 [VGA]) Subsystem: ASUSTeK Computer Inc. Unknown device 034b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M] Expansion ROM at fcfe0000 [disabled] [size=128K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <256ns, L1 <4us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <256ns, L1 <4us Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x16 Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting 02:01.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fdeff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ 02:04.0 Ethernet controller: Atheros Communications, Inc. AR5006X 802.11abg NIC (rev 01) Subsystem: Lite-On Communications Inc Unknown device 5001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2500ns min, 7000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at fdee0000 (32-bit, non-prefetchable) [size=64K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 02:08.0 Ethernet controller: Intel Corporation 82801G (ICH7 Family) LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Unknown device 2a50 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 5 Region 0: Memory at fdefe000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at ef00 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- root@slax:~# root@slax:~# lsmod Module Size Used by snd_seq_dummy 6788 0 snd_seq_oss 32896 0 snd_seq_midi_event 10112 1 snd_seq_oss snd_seq 50640 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 10508 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 42784 0 snd_mixer_oss 18048 1 snd_pcm_oss ipv6 254496 20 pcmcia 34988 0 pcmcia_core 36500 1 pcmcia capability 7304 0 commoncap 9344 1 capability lp 13736 0 parport_pc 27812 0 parport 34760 2 lp,parport_pc pcspkr 6528 0 psmouse 39048 0 zc0301 48004 0 compat_ioctl32 5248 1 zc0301 videodev 29184 1 zc0301 v4l1_compat 17668 1 videodev v4l2_common 18688 2 zc0301,videodev serio_raw 9220 0 i2c_i801 11408 0 evdev 11904 1 ata_generic 9220 0 intel_agp 25116 1 agpgart 31432 1 intel_agp shpchp 33172 0 sg 30364 0 snd_hda_intel 20248 0 snd_hda_codec 209152 1 snd_hda_intel snd_pcm 72068 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec snd_timer 22532 2 snd_seq,snd_pcm snd 47204 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd _timer soundcore 9824 1 snd snd_page_alloc 11528 2 snd_hda_intel,snd_pcm root@slax:~# root@slax:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo root@slax:~#[code] hope this will hhelp:P |
Try typing `modprobe e100` as root and then post the output of `ifconfig -a` afterward. You may wish to run `netconfig` afterwards if the proper network interface is found in ifconfig output. If loading the e100 module detects an interface, you could add the following line to /etc/rc.d/r.modules-$(uname -r)
Code:
/sbin/modprobe e100 |
Quote:
|
Quote:
|
Quote:
Hope this helps, DragonM15 |
Quote:
DragonM15 P.S. I believe there are 2 ways to enable modules, one is editing /etc/modules, and the other is adding a line to /etc/rc.d/rc.modules, is one way "better" than the other? Probably the rc.modules... Also, I dont have an rc.modules-$(uname -r). But I am currently on Slack 10.2. Is that new to Slack 12? |
Quote:
The memory's not what it used to be though ! |
All times are GMT -5. The time now is 08:42 PM. |