adsl & pppoe

hunterfighter · 10-10-2005, 11:44 AM

Hey, I tried install Slackware 10.0 and Slackware 10.2. Which was using adsl-setup and pppoe-setup. But the same result was come out.

It is connected. But I cant surf the net.

/etc/resolv.conf :
nameserver 202.188.0.133
nameserver 202.188.1.5

I setup ADSL by using adsl-setup / pppoe-setup.

Any idea? I am crazy soon.

egag · 10-10-2005, 02:20 PM

so you can ping ip numbers ? and also names ?

what is the output of " route " ?

egag

hunterfighter · 10-10-2005, 07:40 PM

I can ping my NIC
the result of route -n was

<my remote ip> 0.0.0.0
10.0.0.0 0.0.0.0
0.0.0.0 10.1.1.1

egag · 10-10-2005, 07:56 PM

you must post all of the output ( "XXXX" your outside ip)

mine looks like :

------------
10.0.0.0 * 255.255.255.0 U 0 0 0 eth0
192.168.0.0 * 255.255.255.0 U 0 0 0 eth1
loopback * 255.0.0.0 U 0 0 0 lo
default SpeedTouch.lan 0.0.0.0 UG 0 0 0 eth0
-------------

you need one flagged as "UG" .

egag

hunterfighter · 10-10-2005, 08:17 PM

route -n result was

Destination Gateway Genmask Flags Metric Ref Use Iface
10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 lo
0.0.0.0 10.1.1.1 0.0.0.0 UG 0 0 0 eth0

hunterfighter · 10-10-2005, 08:34 PM

As additional information
When I run the adsl-connect
The output will be

notreplacing existing default route to eth0 (10.1.1.1)
Cannot determine ethernet
add from proxy ARP

egag · 10-10-2005, 09:30 PM

your gateway is set to 10.1.1.1 now, and that's wrong.
how do you connect to the web.

you have a nic, connected to a modem or router ?

egag

hunterfighter · 10-10-2005, 10:17 PM

I can ping my gateway = modem and my NIC as well

my modem ip was 10.1.1.1 and NIC ip was 10.1.1.5

hunterfighter · 10-11-2005, 06:59 AM

I had try using FC3. It was working with system-config-network
and I found that
The route table was different with mine.

egag · 10-11-2005, 08:48 AM

if your modem ip is 10.1.1.1 your route table is ok.
in that case you also gotto put 10.1.1.1 in the /etc/resolv.conf file
as first dns server.

i wonder if you need pppoe or adsl-start. ?
if you use a modem/router ( just like i use ) the modem sets up the adsl connection,
and your pc only has to connect to your modem.

egag

hunterfighter · 10-11-2005, 09:50 AM

I did not put nameserver 10.1.1.1 in my /etc/resolv.conf
I will try to check.
Ya, I am using router/modem. But I just used the modem function. I need to connect manually.