LinuxQuestions.org

LinuxQuestions.org (/questions/)
-   Mandriva (https://www.linuxquestions.org/questions/mandriva-30/)
-   -   Please help me understand my dmesg print out. (https://www.linuxquestions.org/questions/mandriva-30/please-help-me-understand-my-dmesg-print-out-156286/)

CyberLord_7 03-11-2004 10:21 AM

Please help me understand my dmesg print out.
 
I am running Mandrake 9.1 on a home made box. I am new to Linux and trying to get my USB pen drives to work. I ran dmesg and got the below print out. I see that my USB ports are recognized, but I'm stuck as to how I can access them. Also, I'm more than a little concerned to see this:

[drm:radeon_unlock] *ERROR* Process 1260 using kernel context 0,

near the bottom of the report. To me "drm" means Digital Rights Management, but since this is in reference to a video card, I'm sure it means something else. At least I hope so. :)
Any help or guidance would be appreciated.
Also, if you see any problems that I should clean up please let me know.
Thank you

***********dmesg follows******************

[root@localhost cyberlord]# dmesg
Linux version 2.4.21-0.13mdk (flepied@bi.mandrakesoft.com) (gcc version 3.2.2 (Mandrake Linux 9.1 3.2.2-3mdk)) #1 Fri Mar 14 15:08:06 EST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
found SMP MP-table at 000fb930
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: VIA Product ID: VT5440B APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 3 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=linux ro root=301 devfs=mount hdc=ide-scsi acpi=off quiet
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1150.086 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 2293.76 BogoMIPS
Memory: 515088k/524224k available (1410k kernel code, 8748k reserved, 1118k data, 136k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
CPU: AMD Athlon(tm) XP stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-17, 2-18, 2-19, 2-20 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 71
0d 001 01 0 0 0 0 0 1 1 79
0e 001 01 0 0 0 0 0 1 1 81
0f 001 01 0 0 0 0 0 1 1 89
10 001 01 1 1 0 1 0 1 1 91
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 99
16 001 01 1 1 0 1 0 1 1 A1
17 001 01 1 1 0 1 0 1 1 A9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1150.0987 MHz.
..... host bus clock speed is 200.0171 MHz.
cpu: 0, clocks: 2000171, slice: 1000085
CPU0<T0:2000160,T1:1000064,D:11,S:1000085,C:2000171>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030122
ACPI: Disabled via command line (acpi=off)
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3177] at 00:11.0
PCI->APIC IRQ transform: (B0,I16,P0) -> 21
PCI->APIC IRQ transform: (B0,I16,P1) -> 21
PCI->APIC IRQ transform: (B0,I16,P2) -> 21
PCI->APIC IRQ transform: (B0,I16,P3) -> 21
PCI->APIC IRQ transform: (B0,I17,P0) -> 22
PCI->APIC IRQ transform: (B0,I17,P2) -> 22
PCI->APIC IRQ transform: (B0,I18,P0) -> 23
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
vesafb: framebuffer at 0xd0000000, mapped to 0xe0800000, size 65536k
vesafb: mode is 800x600x16, linelength=1600, pages=67
vesafb: protected mode interface info at c000:5406
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... found (800x600, 25593 bytes).
Console: switching to colour frame buffer device 80x16
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD800JB-00CRA1, ATA DISK drive
hdb: WDC WD800JB-00CRA1, ATA DISK drive
hda: DMA disabled
blk: queue c03cb420, I/O limit 4095Mb (mask 0xffffffff)
hdb: DMA disabled
blk: queue c03cb55c, I/O limit 4095Mb (mask 0xffffffff)
hdc: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
hdd: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive
hdc: DMA disabled
hdd: DMA disabled
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=9729/255/63, UDMA(100)
hdb: host protected area => 1
hdb: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=9729/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
/dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 p6 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 108k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: ide0(3,1): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 50114
ext3_orphan_cleanup: deleting unreferenced inode 280200
EXT3-fs: ide0(3,1): 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 136k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 15:32:56 Mar 14 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xec00, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
ehci-hcd 00:10.3: VIA Technologies, Inc. USB 2.0
ehci-hcd 00:10.3: irq 21, pci mem e495bf00
usb.c: new USB bus registered, assigned bus number 4
ehci-hcd 00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2002-Dec-20
hub.c: USB hub found
hub.c: 6 ports detected
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Adding Swap: 506008k swap-space (priority -1)
Adding Swap: 506008k swap-space (priority -2)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITE-ON Model: LTR-52246S Rev: 6S0D
Type: CD-ROM ANSI SCSI revision: 02
hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
via-rhine.c:v1.10-LK1.1.15 November-22-2002 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xdc00, 00:0c:76:58:36:52, IRQ 23.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
inserting floppy driver for 2.4.21-0.13mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
PCI: Setting latency timer of device 00:11.5 to 64
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
[drm] Initialized radeon 1.7.0 20020828 on minor 0
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: unable to determine aperture size.
[drm:radeon_unlock] *ERROR* Process 1260 using kernel context 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
Splash status on console 0 changed to off
udf: registering filesystem
end_request: I/O error, dev 02:00 (floppy), sector 0
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
[root@localhost cyberlord]#

************dmesg ends**********************

czarherr 03-11-2004 12:27 PM

ok, here goes

to get to the pen drives, you should just have to mount them as scsi drives, so make a mount point for them, something like /mnt/pendrive or something, so

mount -t vfat /dev/sda1 /mnt/pendrive

and that should work, it may not, in which case post back with the error and we'll see what we can do. Now, for the fun part, i notice you are using a radeon on a KT-400 chipset. same problem i had, now fixed after much much reading.

http://www.linuxquestions.org/questi...0&pagenumber=1

this gets really technical, i waded through it when i first got started in linux, and got it to work, just be patient and very careful. make sure you have atis latest drivers and read this thread, pay attention to jpbarto, and when you have to edit the drivers, you may find the lines to edit in different places than this thread says, just know your motherboard chipset (kx400) and you can find it around the area it says to look. good lluck, let me know how it goes, if i can, i'll help any way possible

oh, and keep in mind im a noob as well, your problem may be different than mine was, so be sure to ask the right questions to get a definite answer. id hate to lead you wrong.

CyberLord_7 03-11-2004 12:30 PM

czarherr:
Thank you for your response. I will print out the thread you provided and try everything tonight.


All times are GMT -5. The time now is 01:46 PM.