Hello. I'm trying to get wired and after that wireless network access with my laptop.
I'm running GNU/Linux x86_64 with 2.6.18-8.el5 kernel. Now I try to get Internet access with my laptop, but I cannot get ip-address to my NIC. Can someone more experienced please help me on this issue, thanks.
I'll put some extra information to this message if someone
with ifconfig -a I get only loopback address and sit0 address, but not for eth1 address.
Here is ifconfig:
***********************************************************************
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2405 errors:0 dropped:0 overruns:0 frame:0
TX packets:2405 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5755875 (5.4 MiB) TX bytes:5755875 (5.4 MiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
***********************************************************************
dmesg prints this:*****************************************************
***********************************************************************
Linux version 2.6.18-8.el5 (brewbuilder@ls20-bc1-14.build.redhat.com) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #1 SMP Fri Jan 26 14:15:14 EST 2007
Command line: ro root=LABEL=/ rhgb quiet crashkernel=128M@16M
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007bf50000 (usable)
BIOS-e820: 000000007bf50000 - 000000007bf65000 (ACPI data)
BIOS-e820: 000000007bf65000 - 000000007bf66000 (ACPI NVS)
BIOS-e820: 000000007bf66000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
ACPI: RSDP (v002 PTLTD ) @ 0x00000000000f8250
ACPI: XSDT (v001 HPQOEM SLIC-MPC 0x06040000 LTP 0x00000000) @ 0x000000007bf5c628
ACPI: FADT (v003 NVIDIA MCP67-M 0x06040000 PTL_ 0x000f4240) @ 0x000000007bf649fc
ACPI: TCPA (v001 Phoeni x 0x06040000 TL 0x00000000) @ 0x000000007bf64af0
ACPI: SRAT (v001 AMD HAMMER 0x06040000 AMD 0x00000001) @ 0x000000007bf64b22
ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x000000007bf64bc2
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x000000007bf64d86
ACPI: HPET (v001 PTLTD HPETTBL 0x06040000 LTP 0x00000001) @ 0x000000007bf64dc2
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x000000007bf64dfa
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x000000007bf64e62
ACPI: SLIC (v001 HPQOEM SLIC-MPC 0x06040000 LTP 0x00000001) @ 0x000000007bf64e8a
ACPI: DSDT (v001 NVIDIA MCP67 0x06040000 MSFT 0x03000000) @ 0x0000000000000000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: Node 0 PXM 0 0-a0000
SRAT: Node 0 PXM 0 0-80000000
NUMA: Using 63 for the hash shift.
Bootmem setup node 0 0000000000000000-000000007bf50000
On node 0 totalpages: 499480
DMA zone: 2733 pages, LIFO batch:0
DMA32 zone: 496747 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:8 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009e000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000d2000
Nosave address range: 00000000000d2000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists. Total pages: 499480
Kernel command line: ro root=LABEL=/ rhgb quiet crashkernel=128M@16M
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ 8418000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 1860944k/2030912k available (2397k kernel code, 169576k reserved, 1222k data, 196k init)
Calibrating delay using timer specific routine.. 3604.24 BogoMIPS (lpj=1802122)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 12502637
Detected 12.502 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3600.37 BogoMIPS (lpj=1800188)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 512 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
time.c: Using 25.000000 MHz WALL HPET GTOD HPET timer.
time.c: Detected 1800.379 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
migration_cost=125
checking if image is initramfs... it is
Freeing initrd memory: 1523k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
PCI: No mmconfig possible on device 0:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:12.0
PCI: Transparent bridge - 0000:00:08.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 16) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5) *10
ACPI: PCI Interrupt Link [LNK2] (IRQs 7) *11
ACPI: PCI Interrupt Link [LNK3] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [LK3E] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [LK4E] (IRQs 19) *10
ACPI: PCI Interrupt Link [LSMB] (IRQs *10)
ACPI: PCI Interrupt Link [LUS0] (IRQs 18) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 22) *7
ACPI: PCI Interrupt Link [LMAC] (IRQs 20) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 21) *10
ACPI: PCI Interrupt Link [LGPU] (IRQs 16) *10
ACPI: PCI Interrupt Link [LPID] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [LSI0] (IRQs 23) *11
ACPI: PCI Interrupt Link [Z015] (IRQs 18) *5
ACPI: PCI Interrupt Link [Z016] (IRQs 22) *10
ACPI: PCI Interrupt Link [LPMU] (IRQs *11)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
PCI-DMA: Disabling IOMMU.
pnp: 00:03: ioport range 0x1000-0x107f could not be reserved
pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
pnp: 00:03: ioport range 0x1400-0x147f has been reserved
pnp: 00:03: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:03: ioport range 0x1800-0x187f has been reserved
pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
PCI: Bridge: 0000:00:08.0
IO window: disabled.
MEM window: f6100000-f61fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: 4000-4fff
MEM window: f2000000-f3ffffff
PREFETCH window: f0000000-f1ffffff
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: f6000000-f60fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:08.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1219077916.301:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 6E92D7462CAE45D
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0

cie00]
Allocate Port Service[0000:00:0c.0

cie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[0563:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0

cie00]
Allocate Port Service[0000:00:0d.0

cie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_thermal-0323): AE_BAD_DATA, No critical threshold [20060707]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: TSSTcorpCD/DVDW TS-L632M, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 processors (version 2.10.00)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x12
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x13
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Write protecting the kernel read-only data: 460k
input: AT Translated Set 2 keyboard as /class/input/input0
Losing some ticks... checking if CPU frequency changed.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 18
GSI 16 sharing vector 0xC1 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 18 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 193, io mem 0xf6486000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 7 ports detected
ACPI: PCI Interrupt Link [Z015] enabled at IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z015] -> GSI 18 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 193, io mem 0xf6487000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
GSI 17 sharing vector 0xC9 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 201, io mem 0xf6489000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 7 ports detected
ACPI: PCI Interrupt Link [Z016] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [Z016] -> GSI 22 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:04.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:04.1
ehci_hcd 0000:00:04.1: irq 201, io mem 0xf6489400
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
sata_nv 0000:00:09.0: version 2.0
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 23
GSI 18 sharing vector 0xD1 and IRQ 18
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 23 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0x30F0 ctl 0x30E6 bmdma 0x30D0 irq 209
ata2: SATA max UDMA/133 cmd 0x30E8 ctl 0x30E2 bmdma 0x30D8 irq 209
scsi0 : sata_nv
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input1
usb 4-2: new high speed USB device using ehci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
ata1: SATA link up <unknown> (SStatus A322FF03 SControl 0)
ATA: abnormal status 0xFF on port 0x30F7
ATA: abnormal status 0xFF on port 0x30F7
ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 0)
ATA: abnormal status 0xFF on port 0x30EF
Vendor: ATA Model: FUJITSU MHW2120B Rev: 8918
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
kjournald starting. Commit interval 5 seconds
....
audit(1219077924.091:3): policy loaded auid=4294967295
input: PC Speaker as /class/input/input2
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
EDAC MC: Ver: 2.0.1 Jan 26 2007
EDAC MC0: Giving out device to k8_edac Athlon64/Opteron: DEV 0000:00:18.2
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:02:05.1 [1180:0822] (rev 22)
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 7
ACPI: PCI Interrupt 0000:02:05.1[B] -> Link [LNK2] -> GSI 7 (level, low) -> IRQ 7
mmc0: SDHCI at 0xf6100800 irq 7 DMA
Floppy drive(s): fd0 is 1.44M
sd 0:0:0:0: Attached scsi generic sg0 type 0
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
lp: driver loaded but no devices found
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
ACPI: Video Device [UVGA] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised:
dm-devel@redhat.com
EXT3 FS on sda1, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda3, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda6, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda2, type ext3), uses xattr
Adding 4096532k swap on /dev/sda7. Priority:-1 extents:1 across:4096532k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.1.0d
ipw3945: Copyright(c) 2003-2006 Intel Corporation
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.retrans_time; Use net.ipv6.neigh.lo.retrans_time_ms instead.
********************************
/var/log/messages prints this***
********************************
Aug 18 20:59:20 localhost kernel: sdb: assuming drive cache: write through
Aug 18 20:59:20 localhost kernel: SCSI device sdb: 8015502 512-byte hdwr sectors (4104 MB)
Aug 18 20:59:20 localhost kernel: sdb: Write Protect is off
Aug 18 20:59:20 localhost kernel: sdb: assuming drive cache: write through
Aug 18 20:59:20 localhost kernel: sdb: sdb1
Aug 18 20:59:20 localhost kernel: sd 3:0:0:0: Attached scsi removable disk sdb
Aug 18 20:59:20 localhost kernel: sd 3:0:0:0: Attached scsi generic sg1 type 0
Aug 18 20:59:20 localhost kernel: Vendor: SanDisk Model: U3 Cruzer Micro Rev: 3.27
Aug 18 20:59:20 localhost kernel: Type: CD-ROM ANSI SCSI revision: 02
Aug 18 20:59:20 localhost kernel: sr0: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray
Aug 18 20:59:20 localhost kernel: sr 3:0:0:1: Attached scsi generic sg2 type 5
Aug 18 20:59:21 localhost kernel: cdrom: This disc doesn't have any tracks I recognize!
Aug 18 20:59:21 localhost kernel: SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
Aug 18 20:59:22 localhost hald: mounted /dev/sdb1 on behalf of uid 500
Aug 18 21:02:48 localhost kernel: usb 3-4: USB disconnect, address 3
Aug 18 21:02:48 localhost kernel: sd 3:0:0:0: rejecting I/O to device being removed
Aug 18 21:02:48 localhost kernel: Buffer I/O error on device sdb1, logical block 15658
Aug 18 21:02:48 localhost kernel: lost page write due to I/O error on sdb1
Aug 18 21:02:48 localhost kernel: sd 3:0:0:0: rejecting I/O to device being removed
Aug 18 21:02:48 localhost kernel: Buffer I/O error on device sdb1, logical block 2640818
Aug 18 21:02:48 localhost kernel: lost page write due to I/O error on sdb1
... ...
Aug 18 21:02:48 localhost hald[3613]: forcibly attempting to lazy unmount /dev/sdb1 as enclosing drive was disconnected
Aug 18 21:02:48 localhost hald: unmounted /dev/sdb1 from '/media/disk' on behalf of uid 0
Aug 18 22:24:06 localhost kernel: usb 3-4: new high speed USB device using ehci_hcd and address 4
Aug 18 22:24:06 localhost kernel: usb 3-4: configuration #1 chosen from 1 choice
Aug 18 22:24:06 localhost kernel: scsi4 : SCSI emulation for USB Mass Storage devices
Aug 18 22:24:11 localhost kernel: Vendor: SanDisk Model: U3 Cruzer Micro Rev: 3.27
Aug 18 22:24:11 localhost kernel: Type: Direct-Access ANSI SCSI revision: 02
************************************************************************
The problem seem to be somewhere in drivers or somewhere else, but I cannot find prober drivers for my laptop.
I'm running RHEL on HP Pavilion dv6000 laptop.
Can someone help me to find solution to this networking problem?
Thanks in advance!
I have also read other messages from here, but hasn't found any proper to my laptop and chipset.
With many thanks!
RHEL5_1979