LinuxQuestions.org - Networking Linux and Windows

- Linux - Wireless Networking (https://www.linuxquestions.org/questions/linux-wireless-networking-41/)

- - Networking Linux and Windows - Ping doesn't work (https://www.linuxquestions.org/questions/linux-wireless-networking-41/networking-linux-and-windows-ping-doesnt-work-146689/)

Networking Linux and Windows - Ping doesn't work

I'm a bit of a newbie to networking under linux(and I'm not that great under windows either ;)) but I'd like to set up my wireless LAN.

I have a proxy server on my host computer, running Windows XP. When I set up my LAN using iwconfig, I can get the little "Connected" icon in the system tray on the host, but ping doesn't work from either computer.

Host IP - 192.168.0.1
Client IP - 192.168.0.2

iwconfig output on Linux:

Code:

eth1      IEEE 802.11-DS  ESSID:"linux"  

          Mode:Ad-Hoc  Frequency:2.412GHz  Cell: 1A:02:51:01:4F:01  

          Bit Rate:11Mb/s  Tx-Power=17 dBm  Sensitivity=0/0  

          Retry limit:16  RTS thr:off  Fragment thr:off

          Encryption key:off

          Power Management:off

          Link Quality:10  Signal level:0  Noise level:0

          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0

          Tx excessive retries:89  Invalid misc:755  Missed beacon:0



wifi0    IEEE 802.11-DS  ESSID:"linux"  

          Mode:Ad-Hoc  Frequency:2.412GHz  Cell: 1A:02:51:01:4F:01  

          Bit Rate:11Mb/s  Tx-Power=17 dBm  Sensitivity=0/0  

          Retry limit:16  RTS thr:off  Fragment thr:off

          Encryption key:off

          Power Management:off

          Link Quality:10  Signal level:0  Noise level:0

          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0

          Tx excessive retries:89  Invalid misc:755  Missed beacon:0

ifconfig -a output:

Code:

eth0      Link encap:Ethernet  HWaddr 00:0D:61:B2:2A:EA  

          inet addr:127.0.0.1  Bcast:127.255.255.255  Mask:255.0.0.0

          UP BROADCAST MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:27 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:0 (0.0 b)  TX bytes:1620 (1.5 Kb)

          Interrupt:17 Base address:0x7e00 



eth1      Link encap:Ethernet  HWaddr 00:0C:30:B0:67:27  

          BROADCAST MULTICAST  MTU:1500  Metric:1

          RX packets:62 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000 

          RX bytes:18995 (18.5 Kb)  TX bytes:0 (0.0 b)

          Interrupt:18 Base address:0xd800 



lo        Link encap:Local Loopback  

          inet addr:127.0.0.1  Mask:255.0.0.0

          UP LOOPBACK RUNNING  MTU:16436  Metric:1

          RX packets:44 errors:0 dropped:0 overruns:0 frame:0

          TX packets:44 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0 

          RX bytes:4300 (4.1 Kb)  TX bytes:4300 (4.1 Kb)



wifi0    Link encap:UNSPEC  HWaddr 00-0C-30-B0-67-27-00-00-00-00-00-00-00-00-00-00  

          inet addr:192.168.0.2  Bcast:192.168.0.255  Mask:255.255.255.0

          UP BROADCAST RUNNING MULTICAST  MTU:2312  Metric:1

          RX packets:62 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:100 

          RX bytes:18995 (18.5 Kb)  TX bytes:0 (0.0 b)

          Interrupt:18 Base address:0xd800

ipconfig under windows output:

Code:





Windows IP Configuration











Ethernet adapter Wireless Network Connection:







        Connection-specific DNS Suffix  . : 



        IP Address. . . . . . . . . . . . : 192.168.0.1



        Subnet Mask . . . . . . . . . . . : 255.255.255.0



        Default Gateway . . . . . . . . . : 



(internet connection below)

I don't think the problem is with the actual wireless cards themselves... but I'm using two Cisco Aironet 350 wireless cards in Ad-Hoc mode.

All of the packets going to the linux box are coming up invalid misc:

Invalid misc:755

Which is bloody weird. Do the Cell's match on either side? Is WEP turned on at all?

Cheers,

Finegan

What do you mean by a cell? I can't seem to find that anyware in the Wireless Settings box.. how could I find that out under Windows?

WEP is totally off. I'll work on getting it secure when I've got it working.

EDIT: I've taken two screenshots of what the Cisco driver statistics & status look like under Windows: (status) (statistics)

bump.. anyone have any idea how to fix this problem?

I got it working.. I used the Cisco official drivers instead of the other ones :)

Posting this using Konqueror right now :D

Ohhh,

Yeah sorry I didn't reply earlier, no inet access followed by a 3 day interview cramb session. Yeah, to explain some things as penance:

IBSS mode, or ad-hoc mode, the card takes its settings and scans accross the channel its given to see if there's already a cell with matching settings, essid, channel, wep, etc... if not, it creates and IBSS infrastructure network and creates its own cell. In a managed/Master network you'll see the MAC of the AP's hardware instead of a cell MAC address that as far as I know is just made up on the spot. Getting another ad-hoc pier to associate with a cell is a little more cumbersome then good old managed and its beacon frames, but by default more secure when running wep because there's just a little less chatter out there in the air... kismet and toys will still sniff one out in relatively short order though... like a week or so.

The firmware shipping with some of the cisco cards was incompatible with a bunch of the kernel drivers from about 2.4.19-22ish I think... and ad-hoc bugs tend to get noticed later as fewer people use that networking type.

Downgrade the firmware and you can switch drivers, which I think is the only way to currently put a cisco in scanning mode, but I might be wrong.

Cheers,

Finegan