replica9000 |
03-10-2007 07:28 PM |
I tried using both -Dndiswrapper and -Dwext, didn't seem to make a difference.
Here is my dmesg output:
Code:
debian-etchtop:/home/replica# dmesg
Linux version 2.6.18-4-k7 (Debian 2.6.18.dfsg.1-11) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Wed Feb 21 16:48:19 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003beb0000 (usable)
BIOS-e820: 000000003beb0000 - 000000003beb8000 (ACPI data)
BIOS-e820: 000000003beb8000 - 000000003bf00000 (ACPI NVS)
BIOS-e820: 000000003bf00000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
62MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f8220
On node 0 totalpages: 245424
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 16048 pages, LIFO batch:3
DMI present.
ACPI: RSDP (v000 GATEWA ) @ 0x000f8190
ACPI: RSDT (v001 GATEWA M300 0x20060124 LTP 0x00000000) @ 0x3beb380a
ACPI: FADT (v001 GATEWA M300 0x20060124 PTL 0x0000005f) @ 0x3beb7e20
ACPI: SSDT (v001 PTLTD POWERNOW 0x20060124 LTP 0x00000001) @ 0x3beb7e94
ACPI: MADT (v001 GATEWA M300 0x20060124 LTP 0x00000000) @ 0x3beb7f6a
ACPI: MCFG (v001 GATEWA M300 0x20060124 LTP 0x00000000) @ 0x3beb7fc4
ACPI: DSDT (v001 GATEWA M300 0x20060124 MSFT 0x0100000e) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 1790.986 MHz processor.
Built 1 zonelists. Total pages: 245424
Kernel command line: root=/dev/hda6 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 965404k/981696k available (1557k kernel code, 15616k reserved, 581k data, 196k init, 64192k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3585.39 BogoMIPS (lpj=7170781)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
CPU0: AMD Turion(tm) 64 Mobile Technology ML-34 stepping 02
Total of 1 processors activated (3585.39 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... failed.
...trying to set up timer as Virtual Wire IRQ... works.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4432k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 2.10 entry at 0xfd89d, last bus=5
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
PCI: Bus #06 (-#09) is hidden behind transparent bridge #05 (-#06) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:09: ioport range 0x1080-0x1080 has been reserved
pnp: 00:09: ioport range 0x220-0x22f has been reserved
pnp: 00:09: ioport range 0x40b-0x40b has been reserved
pnp: 00:09: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: d0100000-d01fffff
PREFETCH window: d4000000-d7ffffff
PCI: Bridge: 0000:00:06.0
IO window: a000-afff
MEM window: d0200000-d02fffff
PREFETCH window: disabled.
PCI: Bus 6, cardbus bridge: 0000:05:09.0
IO window: 00002000-000020ff
IO window: 00002400-000024ff
PREFETCH window: 50000000-51ffffff
MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:14.4
IO window: 2000-2fff
MEM window: d0300000-d03fffff
PREFETCH window: 50000000-51ffffff
PCI: Setting latency timer of device 0000:00:06.0 to 64
ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 23 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:05:09.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1173293727.796:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:06.0 to 64
pcie_portdrv_probe->Dev[5a38:1002] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (65 C)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 201
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 201, io mem 0xd0000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 201
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 201, io mem 0xd0001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
Time: acpi_pm clocksource has been installed.
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 201
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: irq 201, io mem 0xd0002000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 209
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST9120824A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PHILIPS DVD+/-RW SDVD8820, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:05:09.2[C] -> GSI 21 (level, low) -> IRQ 169
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[169] MMIO=[d0308000-d03087ff] Max Packet=[2048] IR/IT contexts=[4/8]
hda: max request size: 512KiB
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 >
hdc: ATAPI 47X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
ReiserFS: hda6: found reiserfs format "3.6" with standard journal
ReiserFS: hda6: using ordered data mode
ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda6: checking transaction log (hda6)
ReiserFS: hda6: Using r5 hash to sort names
Linux agpgart interface v0.101 (c) Dave Jones
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:03:00.0 to 64
sky2 v1.5 addr 0xd0200000 irq 217 Yukon-FE (0xb7) rev 1
sky2 eth0: addr 00:e0:b8:b6:14:82
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
input: PC Speaker as /class/input/input1
Yenta: CardBus bridge found at 0000:05:09.0 [107b:0300]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:05:09.0, mfunc 0x01ac1b22, devctl 0x64
Yenta: ISA IRQ mask 0x0ef8, PCI irq 177
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#05) from #06 to #09
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0300000 - 0xd03fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:05:09.4 [104c:8034] (rev 0)
ACPI: PCI Interrupt 0000:05:09.4[A] -> GSI 23 (level, low) -> IRQ 177
mmc0: SDHCI at 0xd0309000 irq 177 DMA
mmc1: SDHCI at 0xd0308c00 irq 177 DMA
mmc2: SDHCI at 0xd0308800 irq 177 DMA
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 233
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f
cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
cs: IO port probe 0xa00-0xaff: clean.
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x23aeb3, caps: 0xa04713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input2
ts: Compaq touchscreen protocol output
Adding 2522164k swap on /dev/hda7. Priority:-1 extents:1 across:2522164k
loop: loaded (max 8 devices)
SCSI subsystem initialized
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
fuse init (API version 7.7)
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
libata version 2.00 loaded.
sky2 eth1: enabling interface
sky2 eth1: Link is up at 100 Mbps, full duplex, flow control none
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
eth1: no IPv6 routers present
ndiswrapper version 1.38 loaded (preempt=no,smp=yes)
ndiswrapper: driver bcmwl5 (Broadcom,12/22/2004, 3.100.46.0) loaded
ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 22 (level, low) -> IRQ 50
ndiswrapper: using IRQ 50
wlan0: ethernet device 00:14:a5:c1:ce:38 using NDIS driver: bcmwl5, version: 0x3642e00, NDIS version: 0x501, vendor: '', 14E4:4318.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
usbcore: registered new driver ndiswrapper
ndiswrapper: changing interface name from 'wlan0' to 'eth0'
ADDRCONF(NETDEV_UP): eth0: link is not ready
APIC error on CPU0: 00(40)
ohci_hcd 0000:00:13.0: wakeup
usb 1-1: new low speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: USB Mouse as /class/input/input3
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:13.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
|