I'm using Ubuntu 6.06 on my laptop. I'm trying to associate it with my access point using wpa_supplicant. It was working earlier, but now it's not (perhaps because I was fooling around with wpa_supplicant earlier trying to get it to work with WPA2, but then I gave up and reverted back to WPA). Anyways. . .
When I run 'wpa_supplicant -iwlan0 -dd -c/etc/wpa_supplicant/wpa_supplicant.conf -Dwext' I get:
Code:
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
Line: 1 - start of a new network block
ssid - hexdump_ascii(len=21):
42 6f 6f 7a 69 6e 5f 61 6e 64 5f 50 72 61 6e 6b Boozin_and_Prank
73 5f 31 31 67 s_11g
proto: 0x1
key_mgmt: 0x2
PSK - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='Boozin_and_Pranks_11g'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=19 WE(source)=16 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
Own MAC address: 00:13:02:1f:ce:1d
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface wlan0
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Added BSSID 00:00:00:00:00:00 into blacklist
State: SCANNING -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
Scan timeout - try to get results
Received 236 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:0f:b5:92:d3:ad ssid='Boozin_and_Pranks_11g' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0f:b5:92:d3:ad (SSID='Boozin_and_Pranks_11g' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: DISCONNECTED -> ASSOCIATING
wpa_driver_wext_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=30
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)
Cancelling scan request
My wpa_supplicant.conf file is fine. I set it back to the way it was before I started experimenting with WPA2:
Code:
network={
ssid="Boozin_and_Pranks_11g"
proto=WPA
key_mgmt=WPA-PSK
#psk="mypassword"
psk=mypasswordinhex
}
So what am I doing wrong? Is there some module running that shouldn't be running? 'lsmod | grep ieee802' gives me:
Code:
ieee80211 38952 1 ipw3945
ieee80211_crypt 6528 1 ieee80211
ieee80211_1_1_13 39880 0
ieee80211_1_1_13_crypt 7040 1 ieee80211_1_1_13
Thanks for any help.
