[SOLVED] Try to find out whats going on here..

juna11 · 04-23-2013, 12:55 PM

Hello
Everyone..
I having a problem with a ip cam that keeps rebooting, so I open a terminal to what the log would say..
system os looks to be a Linux Here is what the log say
In the log you'll notice it say my reboot, that when the camera reboots and starts to reconnect again,, The camera when it does connect it only connects for 1 min with no video image..
System Log below
Executing image 7 ...
Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0) #
1752 7 27 02:23:14 CST 2012
Processor: Winbond W90N745 revision 1
Architecture: W90N745
On node 0 totalpages: 4096
zone(0): 0 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0 rw
Calibrating delay loop... 39.83 BogoMIPS
Memory: 16MB = 16MB total
Memory: 14316KB available (1490K code, 294K data, 40K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
PTZ Driver has been installed successfully.
Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no s
erial options enabled
ttyS00 at 0xfff80000 (irq = 9) is a W90N745
Winbond W90N7451 Serial driver version 1.0 (2005-08-15) with no
serial options enabled
ttyS00 at 0xfff80100 (irq = 10) is a W90N7451
I2C Bus Driver has been installed successfully.
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 7F0E0000-7F1DE3FF [VIRTUAL 7F0E0000-7F1DE3FF] (RO)
S29GL032N Flash Detected
01 eth0 initial ok!
which:0
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
Winbond Audio Driver v1.0 Initialization successfully.
usb.c: registered new driver hub
add a static ohci host controller device
: USB OHCI at membase 0xfff05000, IRQ 15
hc_alloc_ohci
usb-ohci.c: AMD756 erratum 4 workaround
hc_reset
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver audio
audio.c: v1.0.0:USB Audio Class driver
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.4

_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.24.0.0
usb.c: registered new driver zd1211b
main_usb.c: VIA Networking Wireless LAN USB Driver 1.20.04
usb.c: registered new driver vntwusb
usb.c: registered new driver rt73
dvm usb cam driver 0.0.0.1 by Maverick Gao in 2010-8-3
usb.c: registered new driver dvm
dvm usb cam driver 0.1 for sonix288 by Maverick Gao in 2009-4-20

usb.c: registered new driver dvm usb cam driver for sonix288
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 40K
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
Shell invoked to run file: /bin/init
Command: mount -t proc none /proc
Command: mount -t ramfs none /usr
Command: mount -t ramfs none /swap
Command: mount -t ramfs none /var/run
Command: mount -t ramfs none /etc
Command: mount -t ramfs none /flash
Command: mount -t ramfs none /home
Command: mount -t ramfs none /tmp
Command: mkdir /tmp/run
Command: camera&
no support
[8]
Command: sh

Sash command shell (version 1.1.1)
/> hub.c: connect-debounce failed, port 1 disabled
new USB device :80fb1004-fed740
hub.c: new USB device 1, assigned address 2
probing sonix288 usb camera ...
vid/pid is 0x1d0f/0x1801
dvm camera registered as video0
p1[7]:1,j 3,config->bNumInterfaces:4
usbaudio: device 2 audiocontrol interface 2 has 1 input and 0 ou
tput AudioStreaming interfaces
usbaudio: valid input sample rate 16000
usbaudio: device 2 interface 3 altsetting 1: format 0x00000010 s
ratelo 16000 sratehi 16000 attributes 0x01
usbaudio: valid input sample rate 48000
usbaudio: device 2 interface 3 altsetting 2: format 0x00000010 s
ratelo 48000 sratehi 48000 attributes 0x01
usbaudio: registered dsp 14,35
usbaudio: warning: found 1 of 0 logical channels.
usbaudio: assuming the channel found is the master channel (got
a Philips camera?). Should be fine.
usbaudio: registered mixer 14,32
usb_audio_parsecontrol: usb_audio_state at 00ff3d20
new USB device :80fb1404-fed740
hub.c: new USB device 2, assigned address 3
VIA Networking Wireless LAN USB Driver Ver. 1.20.04
Copyright (c) 2004 VIA Networking Technologies, Inc.
vntwusb_init--->eth1 initial ok!
insmod VNTWUSB SUCESSFUL...
params length is 5428
sw version is 11.22.2.47
aw version is 2.4.10.2

Wait for auto-negotiation complete...OK
100MB - FULL
Config_FileOperation file Not exist
Zone=[2][E][U]!!
Antenna MAIN available!
kernel BUG at consistent.c:42!
video0 opened
1
1
1
1
1
1
unknown command
do_zoom_stop: read error 5
do_focus_stop: read error 5
__pthread_initial_thread_bos:44c000
manage pid:18
dsp and mixer is 7 8
audio_dev.state not AU_STATE_RECORDING
wb_audio_start_record
2
2
2
2
2
2
inet_sr.c INET_rinput 321
action===1
options==33
inet_sr.c INET_setroute 75
*args===255.255.255.255
*args===netmask
*args===eth0
bonjour callback: service registered
do_file: can not find file favicon.ico
video stop 0x6857 0x5c9c
myreboot

W90P745 Boot Loader [ Version 1.1 $Revision: 1 $ ] Rebuilt on Ma
y 11 2010
Memory Size is 0x1000000 Bytes, Flash Size is 0x400000 Bytes
Board designed by Winbond
Hardware support provided at Winbond
Copyright (c) Winbond Limited 2001 - 2006. All rights reserved.
Boot Loader Configuration:

MAC Address : 00:00:00:00:00:01
IP Address : 0.0.0.0
DHCP Client : Enabled
CACHE : Disabled
BL buffer base : 0x00300000
BL buffer size : 0x00100000
Baud Rate : 115200
USB Interface : Enabled
Serial Number : 0x00000000

For help on the available commands type 'h'

Press ESC to enter debug mode ......
Cache disabed!
Processing image 1 ...
Processing image 2 ...
Processing image 3 ...
Processing image 4 ...
Processing image 5 ...
Processing image 6 ...
Processing image 7 ...
Unzip image 7 ...
Executing image 7 ...
Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0)
#1752 7 27 02:23:14 CST 2012
Processor: Winbond W90N745 revision 1
Architecture: W90N745
On node 0 totalpages: 4096
zone(0): 0 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0 rw
Calibrating delay loop... 39.83 BogoMIPS
Memory: 16MB = 16MB total
Memory: 14316KB available (1490K code, 294K data, 40K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
PTZ Driver has been installed successfully.
Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no s
erial options enabled
ttyS00 at 0xfff80000 (irq = 9) is a W90N745
Winbond W90N7451 Serial driver version 1.0 (2005-08-15) with no
serial options enabled
ttyS00 at 0xfff80100 (irq = 10) is a W90N7451
I2C Bus Driver has been installed successfully.
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 7F0E0000-7F1DE3FF [VIRTUAL 7F0E0000-7F1DE3FF] (RO)
S29GL032N Flash Detected
01 eth0 initial ok!
which:0
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
Winbond Audio Driver v1.0 Initialization successfully.
usb.c: registered new driver hub
add a static ohci host controller device
: USB OHCI at membase 0xfff05000, IRQ 15
hc_alloc_ohci
usb-ohci.c: AMD756 erratum 4 workaround
hc_reset
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver audio
audio.c: v1.0.0:USB Audio Class driver
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.4

_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.24.0.0
usb.c: registered new driver zd1211b
main_usb.c: VIA Networking Wireless LAN USB Driver 1.20.04
usb.c: registered new driver vntwusb
usb.c: registered new driver rt73
dvm usb cam driver 0.0.0.1 by Maverick Gao in 2010-8-3
usb.c: registered new driver dvm
dvm usb cam driver 0.1 for sonix288 by Maverick Gao in 2009-4-20

usb.c: registered new driver dvm usb cam driver for sonix288
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 40K
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
Shell invoked to run file: /bin/init
Command: mount -t proc none /proc
Command: mount -t ramfs none /usr
Command: mount -t ramfs none /swap
Command: mount -t ramfs none /var/run
Command: mount -t ramfs none /etc
Command: mount -t ramfs none /flash
Command: mount -t ramfs none /home
Command: mount -t ramfs none /tmp
Command: mkdir /tmp/run
Command: camera&
no support
[8]
Command: sh

Sash command shell (version 1.1.1)
/> hub.c: connect-debounce failed, port 1 disabled
new USB device :80fb1004-fed740
hub.c: new USB device 1, assigned address 2
probing sonix288 usb camera ...
vid/pid is 0x1d0f/0x1801
dvm camera registered as video0
p1[7]:1,j 3,config->bNumInterfaces:4
usbaudio: device 2 audiocontrol interface 2 has 1 input and 0 ou
tput AudioStreaming interfaces
usbaudio: valid input sample rate 16000
usbaudio: device 2 interface 3 altsetting 1: format 0x00000010 s
ratelo 16000 sratehi 16000 attributes 0x01
usbaudio: valid input sample rate 48000
usbaudio: device 2 interface 3 altsetting 2: format 0x00000010 s
ratelo 48000 sratehi 48000 attributes 0x01
usbaudio: registered dsp 14,35
usbaudio: warning: found 1 of 0 logical channels.
usbaudio: assuming the channel found is the master channel (got
a Philips camera?). Should be fine.
usbaudio: registered mixer 14,32
usb_audio_parsecontrol: usb_audio_state at 00ff3d20
new USB device :80fb1404-fed740
hub.c: new USB device 2, assigned address 3
VIA Networking Wireless LAN USB Driver Ver. 1.20.04
Copyright (c) 2004 VIA Networking Technologies, Inc.
vntwusb_init--->eth1 initial ok!
insmod VNTWUSB SUCESSFUL...
params length is 5428
sw version is 11.22.2.47
aw version is 2.4.10.2

Wait for auto-negotiation complete...OK
100MB - FULL
Config_FileOperation file Not exist
Zone=[2][E][U]!!
Antenna MAIN available!
kernel BUG at consistent.c:42!
video0 opened
1
1
1
1
1
1
unknown command
do_zoom_stop: read error 5
do_focus_stop: read error 5
__pthread_initial_thread_bos:44c000
manage pid:18
dsp and mixer is 7 8
audio_dev.state not AU_STATE_RECORDING
wb_audio_start_record
2
2
2
2
2
2
inet_sr.c INET_rinput 321
action===1
options==33
inet_sr.c INET_setroute 75
*args===255.255.255.255
*args===netmask
*args===eth0
bonjour callback: service registered
video stop 0x1e25 0x126b
myreboot

W90P745 Boot Loader [ Version 1.1 $Revision: 1 $ ] Rebuilt on Ma
y 11 2010
Memory Size is 0x1000000 Bytes, Flash Size is 0x400000 Bytes
Board designed by Winbond
Hardware support provided at Winbond
Copyright (c) Winbond Limited 2001 - 2006. All rights reserved.
Boot Loader Configuration:

MAC Address : 00:00:00:00:00:01
IP Address : 0.0.0.0
DHCP Client : Enabled
CACHE : Disabled
BL buffer base : 0x00300000
BL buffer size : 0x00100000
Baud Rate : 115200
USB Interface : Enabled
Serial Number : 0x00000000

For help on the available commands type 'h'

Press ESC to enter debug mode ......
Cache disabed!
Processing image 1 ...
Processing image 2 ...
Processing image 3 ...
Processing image 4 ...
Processing image 5 ...
Processing image 6 ...
Processing image 7 ...
Unzip image 7 ...
Executing image 7 ...
Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0)
#1752 7 27 02:23:14 CST 2012
Processor: Winbond W90N745 revision 1
Architecture: W90N745
On node 0 totalpages: 4096
zone(0): 0 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0 rw
Calibrating delay loop... 39.83 BogoMIPS
Memory: 16MB = 16MB total
Memory: 14316KB available (1490K code, 294K data, 40K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
PTZ Driver has been installed successfully.
Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no s
erial options enabled
ttyS00 at 0xfff80000 (irq = 9) is a W90N745
Winbond W90N7451 Serial driver version 1.0 (2005-08-15) with no
serial options enabled
ttyS00 at 0xfff80100 (irq = 10) is a W90N7451
I2C Bus Driver has been installed successfully.
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: 7F0E0000-7F1DE3FF [VIRTUAL 7F0E0000-7F1DE3FF] (RO)
S29GL032N Flash Detected
01 eth0 initial ok!
which:0
PPP generic driver version 2.4.2
Linux video capture interface: v1.00
Winbond Audio Driver v1.0 Initialization successfully.
usb.c: registered new driver hub
add a static ohci host controller device
: USB OHCI at membase 0xfff05000, IRQ 15
hc_alloc_ohci
usb-ohci.c: AMD756 erratum 4 workaround
hc_reset
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver audio
audio.c: v1.0.0:USB Audio Class driver
usb.c: registered new driver serial
usbserial.c: USB Serial Driver core v1.4

_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.24.0.0
usb.c: registered new driver zd1211b
main_usb.c: VIA Networking Wireless LAN USB Driver 1.20.04
usb.c: registered new driver vntwusb
usb.c: registered new driver rt73
dvm usb cam driver 0.0.0.1 by Maverick Gao in 2010-8-3
usb.c: registered new driver dvm
dvm usb cam driver 0.1 for sonix288 by Maverick Gao in 2009-4-20

usb.c: registered new driver dvm usb cam driver for sonix288
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 40K
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
BINFMT_FLAT: bad magic/rev (0x74202d74, need 0x4)
Shell invoked to run file: /bin/init
Command: mount -t proc none /proc
Command: mount -t ramfs none /usr
Command: mount -t ramfs none /swap
Command: mount -t ramfs none /var/run
Command: mount -t ramfs none /etc
Command: mount -t ramfs none /flash
Command: mount -t ramfs none /home
Command: mount -t ramfs none /tmp
Command: mkdir /tmp/run
Command: camera&
no support
[8]
Command: sh

Sash command shell (version 1.1.1)
/> hub.c: connect-debounce failed, port 1 disabled
new USB device :80fb1004-fed740
hub.c: new USB device 1, assigned address 2
probing sonix288 usb camera ...
vid/pid is 0x1d0f/0x1801
dvm camera registered as video0
p1[7]:1,j 3,config->bNumInterfaces:4
usbaudio: device 2 audiocontrol interface 2 has 1 input and 0 ou
tput AudioStreaming interfaces
usbaudio: valid input sample rate 16000
usbaudio: device 2 interface 3 altsetting 1: format 0x00000010 s
ratelo 16000 sratehi 16000 attributes 0x01
usbaudio: valid input sample rate 48000
usbaudio: device 2 interface 3 altsetting 2: format 0x00000010 s
ratelo 48000 sratehi 48000 attributes 0x01
usbaudio: registered dsp 14,35
usbaudio: warning: found 1 of 0 logical channels.
usbaudio: assuming the channel found is the master channel (got
a Philips camera?). Should be fine.
usbaudio: registered mixer 14,32
usb_audio_parsecontrol: usb_audio_state at 00ff3d20
new USB device :80fb1404-fed740
hub.c: new USB device 2, assigned address 3
VIA Networking Wireless LAN USB Driver Ver. 1.20.04
Copyright (c) 2004 VIA Networking Technologies, Inc.
vntwusb_init--->eth1 initial ok!
insmod VNTWUSB SUCESSFUL...
params length is 5428
sw version is 11.22.2.47
aw version is 2.4.10.2

This is what it does over and over again, I'm wondering if it's a software problem or hardware problem, Please if this is not the right place to ask let me know..
Thanks

unSpawn · 04-23-2013, 01:03 PM

Please post your thread in only one forum. Posting a single thread in the most relevant forum will make it easier for members to help you and will keep the discussion in one place. This thread should be closed because it is a duplicate.

juna11 · 04-23-2013, 02:22 PM

Quote:

Originally Posted by unSpawn

Please post your thread in only one forum. Posting a single thread in the most relevant forum will make it easier for members to help you and will keep the discussion in one place. This thread should be closed because it is a duplicate.

Sorry!!

unSpawn · 04-24-2013, 12:20 AM

Apologies accepted.

Still you should read the http://www.linuxquestions.org/linux/rules.html.