Linux - SoftwareThis forum is for Software issues.
Having a problem installing a new program? Want to know which application is best for the job? Post your question in this forum.
Notices
Welcome to LinuxQuestions.org, a friendly and active Linux Community.
You are currently viewing LQ as a guest. By joining our community you will have the ability to post topics, receive our newsletter, use the advanced search, subscribe to threads and access many other special features. Registration is quick, simple and absolutely free. Join our community today!
Note that registered members see fewer ads, and ContentLink is completely disabled once you log in.
If you have any problems with the registration process or your account login, please contact us. If you need to reset your password, click here.
Having a problem logging in? Please visit this page to clear all LQ-related cookies.
Get a virtual cloud desktop with the Linux distro that you want in less than five minutes with Shells! With over 10 pre-installed distros to choose from, the worry-free installation life is here! Whether you are a digital nomad or just looking for flexibility, Shells can put your Linux machine on the device that you want to use.
Exclusive for LQ members, get up to 45% off per month. Click here for more info.
I dual boot with WinXP and Mandrake 10.1 Linux. I have XP on HDA and MDK on HDB. When I installed MDK I cut the 80 gig hard drive in half. I have used XP to format the last half of the 80gig with fat16. I want to install Slackware 10.0 on the last 40gig of HDB. The setup program does not see that 40. I formatted that 40 with fat16 just so maybe Slackware could see it.
My question: Where can I find the info to tell me how to set up that 40 so I can install Slack without causing problems to my MDK or XP. I have done a little partition work with linux but not much. Not enough to be comfortable with it. I have wanted to try Slack for years but now I have my chance if I can figure out how to get it on my drive.
When you boot with the Slackware CD1, login as root and issue
"cfdisk /dev/hdb" and change that partiton type to ext3 then
write it and exit and run setup. As a general rule, I format
Windoze drives with Windoze tools; and Linux with Linux tools.
Last edited by Bruce Hill; 10-07-2004 at 12:06 AM.
When you use cfdisk, for the partition type choose "Linux", afterwards use mkfs.ext3 /dev/hdX# (where /dev/hdx# is the partition, ex. mkfs.ext3 /dev/hdb2). You won't see an option in cfdisk for Ext3 filesystem.
Originally posted by 95se When you use cfdisk, for the partition type choose "Linux", afterwards use mkfs.ext3 /dev/hdX# (where /dev/hdx# is the partition, ex. mkfs.ext3 /dev/hdb2). You won't see an option in cfdisk for Ext3 filesystem.
Thanks for the correction. I should have said choose Linux type 83
and then when you go through the setup process it will allow you
to format the partitions when you choose the mount points. That
will be much easier for a newbie than using mkfs - IMO.
Thanks! I partitioned the drive and have Slackware installed now. Now the real learning begins. I have to figure out how to get it to recognize my nvidia video card, my Dell monitor, and somehow enable smp for my multi-processor. Sounds like fun. Any suggestions where I can find the docs to do this? I have been looking a little in the man pages. Haven't found anything yet.
The Dell probably needs the correct hor and ver sync rates entered
in /etc/X11/xorg.conf which you might can get from Dell, your monitor's
manual, or searching.
Smb is enabled via the kernel. Kwan Lowe has one of the best kernel guides IMO.
LinuxQuestions.org is looking for people interested in writing
Editorials, Articles, Reviews, and more. If you'd like to contribute
content, let us know.