glxgears FPS is 390, this normal?

Grim Reaper · 09-21-2004, 12:13 AM

Hey Guys,

I've just installed Slackware 10.0 and the NVIDIA drivers for my Geforce MX 440. The glxinfo command says that direct rendering is enabled, and I'm in x at the moment.

I went to install Codega, and in their installation manual, I read this:

Code:

$ glxgears

The glxgears program will output an FPS (Frames Per Second) rating to the 
command line.  If 3D acceleration is correctly enabled for your video card
then the reported FPS should be well over 500 FPS, at the default window size.
If the output shows less than 500 FPS then you should double check your 3D setup.

Now, mine is 390FPS, and from the sounds of things, its not setup correctly, does this seem so? Anybody else out there with the same card as myself? Are TransGaming assuming you should be getting over 500FPS because we all have high end cards?

Hopefully everything is setup correctly

Thank you in advance for all suggestions

EDIT: I've been doing a search on the MX440 and glxgears, and other people are getting around 1700FPS

My system specs are this:
AMD 1600+
Geforce 4 MX440
512 PC-2100 DDR

I'll post my xorg.conf in a separate post for people to have a little squiz at. Thanks.

Here is an output of the GLX gears also:

Code:

leigh@gardiner_desk:~$ glxgears
1583 frames in 5.0 seconds = 316.600 FPS
1940 frames in 5.0 seconds = 388.000 FPS
1946 frames in 5.0 seconds = 389.200 FPS
1946 frames in 5.0 seconds = 389.200 FPS

output of glxinfo:

Code:

leigh@gardiner_desk:~$ glxinfo
name of display: :0.0
display: :0  screen: 0
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.3
server glx extensions:
    GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_SGIX_fbconfig,
    GLX_SGIX_pbuffer, GLX_SGI_video_sync, GLX_SGI_swap_control
client glx vendor string: NVIDIA Corporation
client glx version string: 1.3
client glx extensions:
    GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_visual_info,
    GLX_EXT_visual_rating, GLX_EXT_import_context, GLX_SGI_video_sync,
    GLX_NV_swap_group, GLX_SGIX_fbconfig, GLX_SGIX_pbuffer,
    GLX_SGI_swap_control, GLX_NV_float_buffer
GLX extensions:
    GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_SGIX_fbconfig,
    GLX_SGIX_pbuffer, GLX_SGI_video_sync, GLX_SGI_swap_control,
    GLX_ARB_get_proc_address
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: GeForce4 MX 440/AGP/SSE/3DNOW!
OpenGL version string: 1.5.1 NVIDIA 61.11
OpenGL extensions:
    GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_point_parameters,
    GL_ARB_point_sprite, GL_ARB_shader_objects, GL_ARB_shading_language_100,
    GL_ARB_texture_compression, GL_ARB_texture_cube_map,
    GL_ARB_texture_env_add, GL_ARB_texture_env_combine,
    GL_ARB_texture_env_dot3, GL_ARB_texture_mirrored_repeat,
    GL_ARB_transpose_matrix, GL_ARB_vertex_buffer_object,
    GL_ARB_vertex_program, GL_ARB_vertex_shader, GL_ARB_window_pos,
    GL_S3_s3tc, GL_EXT_texture_env_add, GL_EXT_abgr, GL_EXT_bgra,
    GL_EXT_blend_color, GL_EXT_blend_minmax, GL_EXT_blend_subtract,
    GL_EXT_clip_volume_hint, GL_EXT_compiled_vertex_array,
    GL_EXT_draw_range_elements, GL_EXT_fog_coord, GL_EXT_multi_draw_arrays,
    GL_EXT_packed_pixels, GL_EXT_paletted_texture, GL_EXT_pixel_buffer_object,
    GL_EXT_point_parameters, GL_EXT_rescale_normal, GL_EXT_secondary_color,
    GL_EXT_separate_specular_color, GL_EXT_shared_texture_palette,
    GL_EXT_stencil_wrap, GL_EXT_texture_compression_s3tc,
    GL_EXT_texture_cube_map, GL_EXT_texture_edge_clamp,
    GL_EXT_texture_env_combine, GL_EXT_texture_env_dot3,
    GL_EXT_texture_filter_anisotropic, GL_EXT_texture_lod,
    GL_EXT_texture_lod_bias, GL_EXT_texture_object, GL_EXT_vertex_array,
    GL_IBM_rasterpos_clip, GL_IBM_texture_mirrored_repeat,
    GL_KTX_buffer_region, GL_NV_blend_square, GL_NV_fence,
    GL_NV_fog_distance, GL_NV_light_max_exponent, GL_NV_packed_depth_stencil,
    GL_NV_pixel_data_range, GL_NV_point_sprite, GL_NV_register_combiners,
    GL_NV_texgen_reflection, GL_NV_texture_env_combine4,
    GL_NV_texture_rectangle, GL_NV_vertex_array_range,
    GL_NV_vertex_array_range2, GL_NV_vertex_program, GL_NV_vertex_program1_1,
    GL_SGIS_generate_mipmap, GL_SGIS_multitexture, GL_SGIS_texture_lod,
    GL_SUN_slice_accum
glu version: 1.3
glu extensions:

Hopefully this is enough info to troubleshoot, request anything else that you may need

Grim Reaper · 09-21-2004, 12:21 AM

Code:

# File generated by xf86config.

#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************

# NOTE:  This is a NEW IMPROVED version of XF86Config-fbdev that uses the vesa
# driver instead of the fbdev driver.  Thanks to Kenneth Fanyo who pointed
# this out to me. :)

# This XF86Config file is designed for use with the VESA framebuffer.
# This generic interface should work with nearly all video cards
# (although not every card will support every resolution).

# With the new driver, it should no longer be required to have frame buffer
# support in the kernel, or to run it on the console.
#
# Enjoy! :)
# -- volkerdi@slackware.com
#

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
    Load        "freetype"
    Load        "speedo"

# This loads the GLX module
    Load       "glx"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath	"/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
# 

    FontPath   "/usr/X11R6/lib/X11/fonts/local/"
    FontPath   "/usr/X11R6/lib/X11/fonts/misc/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
    FontPath   "/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath   "/usr/X11R6/lib/X11/fonts/CID/"
    FontPath   "/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath   "/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/100dpi/"
    FontPath   "/usr/X11R6/lib/X11/fonts/cyrillic/"

# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option     "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option     "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option     "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option     "DontZoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option     "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option     "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option     "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option     "AllowNonLocalModInDev"

# Set the basic blanking screen saver timeout.

#    Option      "blank time"    "10"    # 10 minutes

# Set the DPMS timeouts.  These are set here because they are global
# rather than screen-specific.  These settings alone don't enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.

#    Option      "standby time"  "20"
#    Option      "suspend time"  "30"
#    Option      "off time"      "60"

# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don't overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.

# Option   "EstimateSizesAggresively" "0"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier	"Keyboard1"
    Driver	"Keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

# Set the keyboard auto repeat parameters.  Not all platforms implement
# this.

#    Option     "AutoRepeat"    "500 5"

# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)).

#    Option     "Xleds" "1 2 3"

# To disable the XKEYBOARD extension, uncomment XkbDisable.

#    Option     "XkbDisable"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a European
# keyboard, you will probably want to use one of:
#
#    Option     "XkbModel"      "pc102"
#    Option     "XkbModel"      "pc105"
#
# If you have a Microsoft Natural keyboard, you can use:
#
#    Option     "XkbModel"      "microsoft"
#
# If you have a US "windows" keyboard you will want:
#
#    Option     "XkbModel"      "pc104"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#
#    Option     "XkbLayout"     "de"
#
# or:
#
#    Option     "XkbLayout"     "de"
#    Option     "XkbVariant"    "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#
#    Option     "XkbOptions"    "ctrl:swapcaps"


# These are the default XKB settings for X.Org
#
#    Option     "XkbRules"      "xorg"
#    Option     "XkbModel"      "pc101"
#    Option     "XkbLayout"     "us"
#    Option     "XkbVariant"    ""
#    Option     "XkbOptions"    ""

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier	"Mouse1"
    Driver	"mouse"

# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:

#    Option     "Protocol"      "Auto"

# The available mouse protocols types that you can set below are:
#    Auto BusMouse GlidePoint GlidePointPS/2 IntelliMouse IMPS/2
#    Logitech Microsoft MMHitTab MMSeries Mouseman MouseManPlusPS/2
#    MouseSystems NetMousePS/2 NetScrollPS/2 OSMouse PS/2 SysMouse
#    ThinkingMouse ThinkingMousePS/2 Xqueue
    Option "Protocol"    "PS/2"

# The mouse device.  The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.

    Option "Device"      "/dev/mouse"
#   Option "Device"      "/dev/psaux"
#   Option "Device"      "/dev/ttyS0"
#   Option "Device"      "/dev/ttyS1"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"	"Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"		"9600"
#    Option "SampleRate"	"150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection

# Some examples of extended input devices

# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

#    HorizSync   31.5 - 50.0
     HorizSync 30 - 71

#    HorizSync	30-64         # multisync
#    HorizSync	31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync	15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

#    VertRefresh 40-90
     VertRefresh 50-160     

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section "Device"
    Identifier  "VESA Framebuffer"
    Driver      "nvidia"
    #VideoRam    4096
    # Insert Clocks lines here if appropriate
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "VESA Framebuffer"
    Monitor     "My Monitor"

# If your card can handle it, a higher default color depth (like 24 or 32)
# is highly recommended.

#   DefaultDepth 8
#   DefaultDepth 16
   DefaultDepth 24
#   DefaultDepth 32

# "1024x768" is also a conservative usable default resolution.  If you
# have a better monitor, feel free to try resolutions such as
# "1152x864", "1280x1024", "1600x1200", and "1800x1400" (or whatever your
# card/monitor can produce)

    Subsection "Display"
        Depth       8
        Modes "1024x768" "800x600" "640x480"
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes "1024x768" "800x600" "640x480"
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes "1280x1024" "1024x768" "800x600" "640x480"
    EndSubsection
    Subsection "Display"
        Depth       32
        Modes "1024x768" "800x600" "640x480"
    EndSubsection

EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

Hitokiri_X · 09-21-2004, 12:40 AM

Thats odd,your configurations look fine to me.I used to have a GF4 MX440 on my laptop and used to get around 1600 fps.Perhaps it has something to do with rivafb coming with the default installtion of slack.You could try recompiling your own kernel or looking for an option around rivafb.

Grim Reaper · 09-21-2004, 02:23 AM

Thanks for the reply. What is rivafb?

Btw, I thought I should say this: those glxgears FPS values posted above is when glxgears is in focus... when people are taking their values, do they take them with glxgears in focus, or minimized, as when I minimize glxgears, I get around 3695FPS...

Grim Reaper · 09-22-2004, 04:53 AM

bump..

anybody?

Hitokiri_X · 09-22-2004, 06:59 AM

Those should be the values when focused not minimized.Rivafb is blacklisted by default so ignore that part.Also if you're in KDE or Gnome that reduces your fps.Do you have any problems playing games with it and how fast is your system?

Grim Reaper · 09-30-2004, 03:48 AM

my system specs are in the first post, but here they are again

AMD 1600+
Geforce 4 MX440
512 PC-2100 DDR

Yeah I'm in KDE, but that shouldn't make it drop that much should it?