LinuxQuestions.org - [SOLVED] Wireless disconnects and cant re-auth on Fedora 13 x64.

- Linux - Newbie (https://www.linuxquestions.org/questions/linux-newbie-8/)

- - Wireless disconnects and cant re-auth on Fedora 13 x64. (https://www.linuxquestions.org/questions/linux-newbie-8/wireless-disconnects-and-cant-re-auth-on-fedora-13-x64-816127/)

Wireless disconnects and cant re-auth on Fedora 13 x64.

Hi All,

I'm currently using Fedora 13 x64 and have noticed a strange problem with my wireless.

At random intervals it will disconnect, be it 5 minutes or 3 hours and then it will not re-auth no matter how long I leave it. The wireless is running WPA/WPA2, With TKIP/AES encryption. The router only supports b/g and the Wireless NIC is only b/g.

Not sure what driver/software it is using. I noticed I do have wpa_supplicant installed but there doesnt seems to be much happening in /etc/wpa_supplicant/wpa_supplicant.conf apart from the below.

Code:

[daniel@Enterprise ~]$ su -c 'cat /etc/wpa_supplicant/wpa_supplicant.conf'

Password: 



ctrl_interface=/var/run/wpa_supplicant

ctrl_interface_group=wheel



[daniel@Enterprise ~]$

Output of /etc/sysconfig/network-scripts/ifcfg-wlan0

Code:

[root@Enterprise network-scripts]# cat ifcfg-wlan0 



# Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller

DEVICE=wlan0

HWADDR=00:17:3F:87:0E:60

ONBOOT=no



[root@Enterprise network-scripts]#

and just in case this helps

Code:

[daniel@Enterprise ~]$ uname -a



Linux Enterprise 2.6.33.5-124.fc13.x86_64 #1 SMP Fri Jun 11 09:38:12 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux



[daniel@Enterprise ~]$

Any response is much appreciated. thankyou.

I run Fedora 12 (Constantine)...before, I ran Fedora 11 (Leonidas)

What would happen after a certain time is that, when my computer would do certain things I think with power management, sometimes, the wireless card would not connect to the network in the house (my card is BCM4357; my last laptop's card was BCM4312). IRRESPECTIVELY, the connection was unable to be re-established (I assume, though in error possibly, that this is the case with you). So, I would issue the following commands:

Code:

rmmod wl.ko

#Now that the ${BROADCOM}/wl.ko is removed...I may or may not need to do this...

rmmod lib80211

#So, that is that.  I will try again.  First, I wait.  Then...

modprobe lib80211

#This puts one part of the driver in place, but I still need the wl.ko...

insmod ${BROADCOM}/wl.ko

#There, that should work...

The reason I underlined the ${BROADCOM} part is to let you know that wherever the driver is, from there it needs to be accessed. Whenever I did that on my laptop, it seemed to re-establish the connection. Funny, though, with Fedora 12, I never had to worry about that. Hope this helps

Thanks for that PenGUiN_6_1, Unfortunatly it didnt work exactly for 2 reasons, I'm quite new to this and I am prob missing something obvious, Il list the steps I took with your procedure.

On closer inspection of this problem it doesnt seem to be a power/timeout issue, It only disconnects when it is under heavy load (Downloading above 800kbps+)

I done the following with your instructions.

rmmod b43.ko
#the module is named b43.ko, This however removed the wireless which i believe is correct.

rmmod lib80211
#I do have this module on my system as I found the lib80211.ko but it wasnt loaded

insmod b43.ko
#I tried this however it brought up the following error message.
(insmod: error inserting 'b43.ko': -1 Invalid module format)

I went into the location of the drivers before doing any commands.
(/lib/modules/2.6.33.5-124.fc13.x86_64/kernel/drivers/net/wireless/b43/) for b43.ko etc

So hopefully its just a case of loading that module again, Although I would like a more permanent solution and not have to unload/load a module everytime this happens.

Please bare with me as I am prob doing this all wrong!

Thankyou for any help.

Unfortunately I am unsure of such a solution. Believe it or not, another computer I know of had the same problem with Windows Vista...every so often it has to reauthenticate...even with a WIRED connection!