LinuxQuestions.org - [SOLVED] Upgrade to jessie but lost wifi network

- Linux - Newbie (https://www.linuxquestions.org/questions/linux-newbie-8/)

- - Upgrade to jessie but lost wifi network (https://www.linuxquestions.org/questions/linux-newbie-8/upgrade-to-jessie-but-lost-wifi-network-4175552862/)

Upgrade to jessie but lost wifi network

As I had a similar problem when I first installed wheezy, I followed the instructions on https://wiki.debian.org/wl

I think I should not have followed item 3.

Quote:

Unload conflicting modules:
# modprobe -r b44 b43 b43legacy ssb brcmsmac

My laptop has no wifi and it is difficult to get a wired connection since it is dedicated to my partner's business setup.

Quote:

Originally Posted by kestreltowers (Post 5417153)

My laptop has no wifi and it is difficult to get a wired connection since it is dedicated to my partner's business setup.

Hi...

Getting a wired connection may be a necessity, just to make you aware. :(

I'm not sure I can help here but can you open a terminal and post the entire results of the following commands...

Code:

lspci -nnk | grep -i net -A2

Code:

iwconfig

Code:

rfkill list

Code:

dmesg

If you can't get a wired connection with this system, you can copy and paste the results to a text file and then save it on a thumb drive. The dmesg report will be long, you may need to separate the results into more than one post. ;)

Regards...

Thank you, Ardvark71. It is impossible for a beginner to search for answers.
lscpi result is

Code:

tuddy@tycornel:~$ lspci -nnk | grep -i net -A2

01:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe [14e4:1692] (rev 01)

        Subsystem: Acer Incorporated [ALI] Device [1025:047f]

        Kernel driver in use: tg3

02:00.0 Network controller [0280]: Broadcom Corporation BCM43225 802.11b/g/n [14e4:4357] (rev 01)

        Subsystem: Foxconn International, Inc. T77H103.00 Wireless Half-size Mini PCIe Card [105b:e021]

7f:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers [8086:2c62] (rev 05)

iwconfig result is

Code:

tuddy@tycornel:~$ /sbin/iwconfig

lo        no wireless extensions.



eth0      no wireless extensions.

I failed to run rfkill.

Code:

root@tycornel:/home/tuddy# /dev/rfkill list

bash: /dev/rfkill: Permission denied

root@tycornel:/home/tuddy# type /dev/rfkill

bash: type: /dev/rfkill: not found

root@tycornel:/home/tuddy# ls -l /dev/rfkill

crw-rw-r--+ 1 root root 10, 59 Sep  8  2015 /dev/rfkill

root@tycornel:/home/tuddy# cd /dev

root@tycornel:/dev# rfkill list

bash: rfkill: command not found

root@tycornel:/dev# type rfkill

bash: type: rfkill: not found

dmesg in installments
1

Code:

tuddy@tycornel:~$ dmesg

[    0.000000] Initializing cgroup subsys cpuset

[    0.000000] Initializing cgroup subsys cpu

[    0.000000] Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.68-1+deb7u3

[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=a4229f23-a7d8-402a-bd7b-aaf696480f69 ro quiet

[    0.000000] BIOS-provided physical RAM map:

[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009d000 (usable)

[    0.000000]  BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved)

[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)

[    0.000000]  BIOS-e820: 0000000000100000 - 00000000af681000 (usable)

[    0.000000]  BIOS-e820: 00000000af681000 - 00000000af6bf000 (reserved)

[    0.000000]  BIOS-e820: 00000000af6bf000 - 00000000af74d000 (usable)

[    0.000000]  BIOS-e820: 00000000af74d000 - 00000000af7bf000 (ACPI NVS)

[    0.000000]  BIOS-e820: 00000000af7bf000 - 00000000af7e3000 (usable)

[    0.000000]  BIOS-e820: 00000000af7e3000 - 00000000af7ff000 (ACPI data)

[    0.000000]  BIOS-e820: 00000000af7ff000 - 00000000af800000 (usable)

[    0.000000]  BIOS-e820: 00000000af800000 - 00000000bc000000 (reserved)

[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f8000000 (reserved)

[    0.000000]  BIOS-e820: 00000000feb00000 - 00000000feb04000 (reserved)

[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)

[    0.000000]  BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)

[    0.000000]  BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)

[    0.000000]  BIOS-e820: 00000000fed1b000 - 00000000fed20000 (reserved)

[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)

[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)

[    0.000000] NX (Execute Disable) protection: active

[    0.000000] SMBIOS 2.6 present.

[    0.000000] DMI: eMachines eME732Z/HM55_CP, BIOS V1.06 10/22/2010

[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)

[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)

[    0.000000] No AGP bridge found

[    0.000000] last_pfn = 0xaf800 max_arch_pfn = 0x400000000

[    0.000000] MTRR default type: uncachable

[    0.000000] MTRR fixed ranges enabled:

[    0.000000]  00000-9FFFF write-back

[    0.000000]  A0000-BFFFF uncachable

[    0.000000]  C0000-EFFFF write-through

[    0.000000]  F0000-FFFFF write-combining

[    0.000000] MTRR variable ranges enabled:

[    0.000000]  0 base 000000000 mask F80000000 write-back

[    0.000000]  1 base 0FFE00000 mask FFFE00000 write-protect

[    0.000000]  2 base 080000000 mask FC0000000 write-back

[    0.000000]  3 base 0B0000000 mask FF0000000 uncachable

[    0.000000]  4 base 0AF800000 mask FFF800000 uncachable

[    0.000000]  5 disabled

[    0.000000]  6 disabled

[    0.000000]  7 disabled

[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106

[    0.000000] initial memory mapped : 0 - 20000000

[    0.000000] Base memory trampoline at [ffff880000098000] 98000 size 20480

[    0.000000] init_memory_mapping: 0000000000000000-00000000af800000

[    0.000000]  0000000000 - 00af800000 page 2M

[    0.000000] kernel direct mapping tables up to af800000 @ 1fffc000-20000000

[    0.000000] RAMDISK: 36a34000 - 37512000

[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)

[    0.000000] ACPI: XSDT 00000000af7fe120 00074 (v01 ACRSYS ACRPRDCT 00000001      01000013)

[    0.000000] ACPI: FACP 00000000af7fc000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: DSDT 00000000af7ed000 0B07E (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: FACS 00000000af75f000 00040

[    0.000000] ACPI: ASF! 00000000af7fd000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: HPET 00000000af7fb000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: APIC 00000000af7fa000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: MCFG 00000000af7f9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: SLIC 00000000af7ec000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: BOOT 00000000af7e9000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: ASPT 00000000af7e5000 00034 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: WDAT 00000000af7e4000 00224 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)

[    0.000000] ACPI: SSDT 00000000af7e3000 009F1 (v01  PmRef    CpuPm 00003000 INTL 20051117)

[    0.000000] ACPI: Local APIC address 0xfee00000

[    0.000000] No NUMA configuration found

[    0.000000] Faking a node at 0000000000000000-00000000af800000

[    0.000000] Initmem setup node 0 0000000000000000-00000000af800000

[    0.000000]  NODE_DATA [00000000af7de000 - 00000000af7e2fff]

[    0.000000]  [ffffea0000000000-ffffea00027fffff] PMD -> [ffff8800ac200000-ffff8800ae9fffff] on node 0

[    0.000000] Zone PFN ranges:

[    0.000000]  DMA      0x00000010 -> 0x00001000

[    0.000000]  DMA32    0x00001000 -> 0x00100000

[    0.000000]  Normal  empty

[    0.000000] Movable zone start PFN for each node

[    0.000000] early_node_map[5] active PFN ranges

[    0.000000]    0: 0x00000010 -> 0x0000009d

[    0.000000]    0: 0x00000100 -> 0x000af681

[    0.000000]    0: 0x000af6bf -> 0x000af74d

[    0.000000]    0: 0x000af7bf -> 0x000af7e3

[    0.000000]    0: 0x000af7ff -> 0x000af800

[    0.000000] On node 0 totalpages: 718529

[    0.000000]  DMA zone: 56 pages used for memmap

[    0.000000]  DMA zone: 5 pages reserved

[    0.000000]  DMA zone: 3920 pages, LIFO batch:0

[    0.000000]  DMA32 zone: 9772 pages used for memmap

[    0.000000]  DMA32 zone: 704776 pages, LIFO batch:31

[    0.000000] ACPI: PM-Timer IO Port: 0x408

[    0.000000] ACPI: Local APIC address 0xfee00000

[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)

[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)

[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])

[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23

[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)

[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)

[    0.000000] ACPI: IRQ0 used by override.

[    0.000000] ACPI: IRQ2 used by override.

[    0.000000] ACPI: IRQ9 used by override.

[    0.000000] Using ACPI (MADT) for SMP configuration information

[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000

[    0.000000] SMP: Allowing 8 CPUs, 6 hotplug CPUs

[    0.000000] nr_irqs_gsi: 40

[    0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000

[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000

[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000

[    0.000000] PM: Registered nosave memory: 00000000af681000 - 00000000af6bf000

[    0.000000] PM: Registered nosave memory: 00000000af74d000 - 00000000af7bf000

[    0.000000] PM: Registered nosave memory: 00000000af7e3000 - 00000000af7ff000

[    0.000000] Allocating PCI resources starting at bc000000 (gap: bc000000:34000000)

[    0.000000] Booting paravirtualized kernel on bare hardware

[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:1

[    0.000000] PERCPU: Embedded 27 pages/cpu @ffff8800af400000 s78912 r8192 d23488 u262144

[    0.000000] pcpu-alloc: s78912 r8192 d23488 u262144 alloc=1*2097152

[    0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 

[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 708696

[    0.000000] Policy zone: DMA32

[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=a4229f23-a7d8-402a-bd7b-aaf696480f69 ro quiet

[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)

[    0.000000] Checking aperture...

[    0.000000] No AGP bridge found

[    0.000000] Calgary: detecting Calgary via BIOS EBDA area

[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!

[    0.000000] Memory: 2812632k/2875392k available (3434k kernel code, 1276k absent, 61484k reserved, 3305k data, 580k init)

[    0.000000] Hierarchical RCU implementation.

[    0.000000]        RCU dyntick-idle grace-period acceleration is enabled.

[    0.000000] NR_IRQS:33024 nr_irqs:744 16

[    0.000000] Extended CMOS year: 2000

[    0.000000] Console: colour VGA+ 80x25

[    0.000000] console [tty0] enabled

[    0.000000] hpet clockevent registered

[    0.000000] Fast TSC calibration using PIT

[    0.004000] Detected 2127.852 MHz processor.

[    0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4255.70 BogoMIPS (lpj=8511408)

[    0.000008] pid_max: default: 32768 minimum: 301

[    0.000055] Security Framework initialized

[    0.000060] AppArmor: AppArmor disabled by boot time parameter

[    0.000327] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)

[    0.001935] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)

[    0.002663] Mount-cache hash table entries: 256

cont/... in next post

cont. from previous post:

dmesg part 2

Code:

[    0.002793] Initializing cgroup subsys cpuacct

[    0.002799] Initializing cgroup subsys memory

[    0.002811] Initializing cgroup subsys devices

[    0.002815] Initializing cgroup subsys freezer

[    0.002817] Initializing cgroup subsys net_cls

[    0.002819] Initializing cgroup subsys blkio

[    0.002825] Initializing cgroup subsys perf_event

[    0.002855] CPU: Physical Processor ID: 0

[    0.002857] CPU: Processor Core ID: 0

[    0.002862] mce: CPU supports 9 MCE banks

[    0.002874] CPU0: Thermal monitoring enabled (TM1)

[    0.002882] using mwait in idle threads.

[    0.003330] ACPI: Core revision 20110623

[    0.034537] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1

[    0.074203] CPU0: Intel(R) Pentium(R) CPU        P6200  @ 2.13GHz stepping 05

[    0.179581] Performance Events: PEBS fmt1+, Westmere events, Intel PMU driver.

[    0.179589] ... version:                3

[    0.179590] ... bit width:              48

[    0.179592] ... generic registers:      4

[    0.179593] ... value mask:            0000ffffffffffff

[    0.179595] ... max period:            000000007fffffff

[    0.179596] ... fixed-purpose events:  3

[    0.179598] ... event mask:            000000070000000f

[    0.179872] NMI watchdog enabled, takes one hw-pmu counter.

[    0.179998] Booting Node  0, Processors  #1

[    0.180001] smpboot cpu 1: start_ip = 98000

[    0.287664] NMI watchdog enabled, takes one hw-pmu counter.

[    0.287707] Brought up 2 CPUs

[    0.287709] Total of 2 processors activated (8511.62 BogoMIPS).

[    0.289042] devtmpfs: initialized

[    0.293331] PM: Registering ACPI NVS region at af74d000 (466944 bytes)

[    0.293512] print_constraints: dummy: 

[    0.293573] NET: Registered protocol family 16

[    0.293680] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it

[    0.293683] ACPI: bus type pci registered

[    0.293778] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)

[    0.293782] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820

[    0.300798] PCI: Using configuration type 1 for base access

[    0.300921] mtrr: your CPUs had inconsistent variable MTRR settings

[    0.300923] mtrr: probably your BIOS does not setup all CPUs.

[    0.300924] mtrr: corrected configuration.

[    0.301540] bio: create slab <bio-0> at 0

[    0.301642] ACPI: Added _OSI(Module Device)

[    0.301645] ACPI: Added _OSI(Processor Device)

[    0.301647] ACPI: Added _OSI(3.0 _SCP Extensions)

[    0.301650] ACPI: Added _OSI(Processor Aggregator Device)

[    0.303704] ACPI: EC: Look up EC in DSDT

[    0.319601] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored

[    0.332177] ACPI: SSDT 00000000af691c18 003AE (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)

[    0.332697] ACPI: Dynamic OEM Table Load:

[    0.332700] ACPI: SSDT          (null) 003AE (v01  PmRef  Cpu0Ist 00003000 INTL 20051117)

[    0.332935] ACPI: SSDT 00000000af68f018 00891 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)

[    0.333394] ACPI: Dynamic OEM Table Load:

[    0.333397] ACPI: SSDT          (null) 00891 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)

[    0.355939] ACPI: SSDT 00000000af690a98 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)

[    0.356519] ACPI: Dynamic OEM Table Load:

[    0.356522] ACPI: SSDT          (null) 00303 (v01  PmRef    ApIst 00003000 INTL 20051117)

[    0.367725] ACPI: SSDT 00000000af68ed98 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)

[    0.368242] ACPI: Dynamic OEM Table Load:

[    0.368244] ACPI: SSDT          (null) 00119 (v01  PmRef    ApCst 00003000 INTL 20051117)

[    0.379883] ACPI: Interpreter enabled

[    0.379888] ACPI: (supports S0 S3 S4 S5)

[    0.379928] ACPI: Using IOAPIC for interrupt routing

[    0.385414] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62

[    0.385611] ACPI: No dock devices found.

[    0.385613] HEST: Table not found.

[    0.385616] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

[    0.386118] \_SB_.PCI0:_OSC invalid UUID

[    0.386120] _OSC request data:1 8 0 

[    0.386124] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])

[    0.386967] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]

[    0.386970] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]

[    0.386973] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]

[    0.386976] pci_root PNP0A08:00: host bridge window [mem 0xbc000000-0xfeafffff]

[    0.386989] pci 0000:00:00.0: [8086:0044] type 0 class 0x000600

[    0.387008] DMAR: BIOS has allocated no shadow GTT; disabling IOMMU for graphics

[    0.387033] pci 0000:00:02.0: [8086:0046] type 0 class 0x000300

[    0.387045] pci 0000:00:02.0: reg 10: [mem 0xd0000000-0xd03fffff 64bit]

[    0.387052] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]

[    0.387057] pci 0000:00:02.0: reg 20: [io  0x3050-0x3057]

[    0.387125] pci 0000:00:16.0: [8086:3b64] type 0 class 0x000780

[    0.387154] pci 0000:00:16.0: reg 10: [mem 0xd4406100-0xd440610f 64bit]

[    0.387250] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold

[    0.387297] pci 0000:00:1a.0: [8086:3b3c] type 0 class 0x000c03

[    0.387685] pci 0000:00:1a.0: reg 10: [mem 0xd4405c00-0xd4405fff]

[    0.389833] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold

[    0.389871] pci 0000:00:1b.0: [8086:3b56] type 0 class 0x000403

[    0.389892] pci 0000:00:1b.0: reg 10: [mem 0xd4400000-0xd4403fff 64bit]

[    0.389991] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold

[    0.390024] pci 0000:00:1c.0: [8086:3b42] type 1 class 0x000604

[    0.390127] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold

[    0.390166] pci 0000:00:1c.5: [8086:3b4c] type 1 class 0x000604

[    0.390268] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold

[    0.390312] pci 0000:00:1d.0: [8086:3b34] type 0 class 0x000c03

[    0.390677] pci 0000:00:1d.0: reg 10: [mem 0xd4405800-0xd4405bff]

[    0.392829] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold

[    0.392860] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604

[    0.392950] pci 0000:00:1f.0: [8086:3b09] type 0 class 0x000601

[    0.393082] pci 0000:00:1f.2: [8086:3b29] type 0 class 0x000106

[    0.393110] pci 0000:00:1f.2: reg 10: [io  0x3048-0x304f]

[    0.393122] pci 0000:00:1f.2: reg 14: [io  0x305c-0x305f]

[    0.393133] pci 0000:00:1f.2: reg 18: [io  0x3040-0x3047]

[    0.393145] pci 0000:00:1f.2: reg 1c: [io  0x3058-0x305b]

[    0.393156] pci 0000:00:1f.2: reg 20: [io  0x3020-0x303f]

[    0.393167] pci 0000:00:1f.2: reg 24: [mem 0xd4405000-0xd44057ff]

[    0.393235] pci 0000:00:1f.2: PME# supported from D3hot

[    0.393262] pci 0000:00:1f.3: [8086:3b30] type 0 class 0x000c05

[    0.393284] pci 0000:00:1f.3: reg 10: [mem 0xd4406000-0xd44060ff 64bit]

[    0.393314] pci 0000:00:1f.3: reg 20: [io  0x3000-0x301f]

[    0.393365] pci 0000:00:1f.6: [8086:3b32] type 0 class 0x001180

[    0.393394] pci 0000:00:1f.6: reg 10: [mem 0xd4404000-0xd4404fff 64bit]

[    0.393611] pci 0000:01:00.0: [14e4:1692] type 0 class 0x000200

[    0.393642] pci 0000:01:00.0: reg 10: [mem 0xd3400000-0xd340ffff 64bit]

[    0.393805] pci 0000:01:00.0: PME# supported from D3hot D3cold

[    0.399543] pci 0000:00:1c.0: PCI bridge to [bus 01-01]

[    0.399552] pci 0000:00:1c.0:  bridge window [io  0x2000-0x2fff]

[    0.399561] pci 0000:00:1c.0:  bridge window [mem 0xd3400000-0xd43fffff]

[    0.399574] pci 0000:00:1c.0:  bridge window [mem 0xd0400000-0xd13fffff 64bit pref]

[    0.399699] pci 0000:02:00.0: [14e4:4357] type 0 class 0x000280

[    0.399730] pci 0000:02:00.0: reg 10: [mem 0xd2400000-0xd2403fff 64bit]

[    0.399895] pci 0000:02:00.0: supports D1 D2

[    0.399897] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold

[    0.407535] pci 0000:00:1c.5: PCI bridge to [bus 02-02]

[    0.407544] pci 0000:00:1c.5:  bridge window [io  0x1000-0x1fff]

[    0.407553] pci 0000:00:1c.5:  bridge window [mem 0xd2400000-0xd33fffff]

[    0.407567] pci 0000:00:1c.5:  bridge window [mem 0xd1400000-0xd23fffff 64bit pref]

[    0.407651] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)

[    0.407665] pci 0000:00:1e.0:  bridge window [io  0x0000-0x0cf7] (subtractive decode)

[    0.407668] pci 0000:00:1e.0:  bridge window [io  0x0d00-0xffff] (subtractive decode)

[    0.407671] pci 0000:00:1e.0:  bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)

[    0.407674] pci 0000:00:1e.0:  bridge window [mem 0xbc000000-0xfeafffff] (subtractive decode)

[    0.407696] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

[    0.407958] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]

[    0.408057] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]

[    0.408193] \_SB_.PCI0:_OSC invalid UUID

[    0.408195] _OSC request data:1 1f 0 

[    0.408199]  pci0000:00: Requesting ACPI _OSC control (0x1d)

[    0.408244] \_SB_.PCI0:_OSC invalid UUID

[    0.408246] _OSC request data:1 0 1d 

[    0.408250]  pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d

[    0.408251] ACPI _OSC control for PCIe not granted, disabling ASPM

[    0.413440] ACPI: PCI Root Bridge [CPBG] (domain 0000 [bus 7f])

[    0.413531] pci 0000:7f:00.0: [8086:2c62] type 0 class 0x000600

[    0.413554] pci 0000:7f:00.1: [8086:2d01] type 0 class 0x000600

[    0.413576] pci 0000:7f:02.0: [8086:2d10] type 0 class 0x000600

[    0.413597] pci 0000:7f:02.1: [8086:2d11] type 0 class 0x000600

[    0.413616] pci 0000:7f:02.2: [8086:2d12] type 0 class 0x000600

[    0.413636] pci 0000:7f:02.3: [8086:2d13] type 0 class 0x000600

[    0.413671]  pci0000:7f: Requesting ACPI _OSC control (0x1d)

[    0.413674]  pci0000:7f: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d

Code:

[    0.413676] ACPI _OSC control for PCIe not granted, disabling ASPM

[    0.413976] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11

[    0.414034] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)

[    0.414090] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.

[    0.414146] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10

[    0.414202] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.

[    0.414258] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)

[    0.414314] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11

[    0.414371] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)

[    0.414491] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none

[    0.414501] vgaarb: loaded

[    0.414503] vgaarb: bridge control possible 0000:00:02.0

[    0.414546] PCI: Using ACPI for IRQ routing

[    0.419414] PCI: pci_cache_line_size set to 64 bytes

[    0.419584] reserve RAM buffer: 000000000009d000 - 000000000009ffff 

[    0.419587] reserve RAM buffer: 00000000af681000 - 00000000afffffff 

[    0.419589] reserve RAM buffer: 00000000af74d000 - 00000000afffffff 

[    0.419592] reserve RAM buffer: 00000000af7e3000 - 00000000afffffff 

[    0.419594] reserve RAM buffer: 00000000af800000 - 00000000afffffff 

[    0.419726] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0

[    0.419733] hpet0: 8 comparators, 64-bit 14.318180 MHz counter

[    0.421751] Switching to clocksource hpet

[    0.423799] pnp: PnP ACPI init

[    0.423815] ACPI: bus type pnp registered

[    0.424259] pnp 00:00: [bus 00-7e]

[    0.424262] pnp 00:00: [io  0x0000-0x0cf7 window]

[    0.424264] pnp 00:00: [io  0x0cf8-0x0cff]

[    0.424267] pnp 00:00: [io  0x0d00-0xffff window]

[    0.424269] pnp 00:00: [mem 0x000a0000-0x000bffff window]

[    0.424271] pnp 00:00: [mem 0x000c0000-0x000c3fff window]

[    0.424274] pnp 00:00: [mem 0x000c4000-0x000c7fff window]

[    0.424276] pnp 00:00: [mem 0x000c8000-0x000cbfff window]

[    0.424278] pnp 00:00: [mem 0x000cc000-0x000cffff window]

[    0.424280] pnp 00:00: [mem 0x000d0000-0x000d3fff window]

[    0.424282] pnp 00:00: [mem 0x000d4000-0x000d7fff window]

[    0.424285] pnp 00:00: [mem 0x000d8000-0x000dbfff window]

[    0.424287] pnp 00:00: [mem 0x000dc000-0x000dffff window]

[    0.424289] pnp 00:00: [mem 0x000e0000-0x000e3fff window]

[    0.424291] pnp 00:00: [mem 0x000e4000-0x000e7fff window]

[    0.424293] pnp 00:00: [mem 0x000e8000-0x000ebfff window]

[    0.424295] pnp 00:00: [mem 0x000ec000-0x000effff window]

[    0.424298] pnp 00:00: [mem 0x000f0000-0x000fffff window]

[    0.424301] pnp 00:00: [mem 0xbc000000-0xfeafffff window]

[    0.424304] pnp 00:00: [mem 0xfed40000-0xfed44fff window]

[    0.424363] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)

[    0.424424] pnp 00:01: [io  0x0000-0x001f]

[    0.424426] pnp 00:01: [io  0x0081-0x0091]

[    0.424428] pnp 00:01: [io  0x0093-0x009f]

[    0.424430] pnp 00:01: [io  0x00c0-0x00df]

[    0.424433] pnp 00:01: [dma 4]

[    0.424467] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)

[    0.424478] pnp 00:02: [mem 0xff000000-0xffffffff]

[    0.424506] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)

[    0.424615] pnp 00:03: [mem 0xfed00000-0xfed003ff]

[    0.424647] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)

[    0.424660] pnp 00:04: [io  0x00f0]

[    0.424671] pnp 00:04: [irq 13]

[    0.424701] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)

[    0.424714] pnp 00:05: [io  0x002e-0x002f]

[    0.424716] pnp 00:05: [io  0x004e-0x004f]

[    0.424718] pnp 00:05: [io  0x0061]

[    0.424720] pnp 00:05: [io  0x0063]

[    0.424722] pnp 00:05: [io  0x0065]

[    0.424724] pnp 00:05: [io  0x0067]

[    0.424726] pnp 00:05: [io  0x0070]

[    0.424728] pnp 00:05: [io  0x0080]

[    0.424730] pnp 00:05: [io  0x0092]

[    0.424732] pnp 00:05: [io  0x00b2-0x00b3]

[    0.424734] pnp 00:05: [io  0x0680-0x069f]

[    0.424736] pnp 00:05: [io  0x0800-0x080f]

[    0.424738] pnp 00:05: [io  0xffff]

[    0.424740] pnp 00:05: [io  0xffff]

[    0.424742] pnp 00:05: [io  0x0400-0x047f]

[    0.424744] pnp 00:05: [io  0x0500-0x057f]

[    0.424746] pnp 00:05: [io  0x164e-0x164f]

[    0.424758] pnp 00:05: disabling [io  0x164e-0x164f] because it overlaps 0000:00:1c.5 BAR 13 [io  0x1000-0x1fff]

[    0.424806] system 00:05: [io  0x0680-0x069f] has been reserved

[    0.424809] system 00:05: [io  0x0800-0x080f] has been reserved

[    0.424812] system 00:05: [io  0xffff] has been reserved

[    0.424815] system 00:05: [io  0xffff] has been reserved

[    0.424818] system 00:05: [io  0x0400-0x047f] has been reserved

[    0.424821] system 00:05: [io  0x0500-0x057f] has been reserved

[    0.424824] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)

[    0.424836] pnp 00:06: [io  0x0070-0x0077]

[    0.424842] pnp 00:06: [irq 8]

[    0.424873] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)

[    0.424886] pnp 00:07: [io  0x0060]

[    0.424888] pnp 00:07: [io  0x0064]

[    0.424894] pnp 00:07: [irq 1]

[    0.424925] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active)

[    0.424939] pnp 00:08: [irq 12]

[    0.424971] pnp 00:08: Plug and Play ACPI device, IDs SYN1b20 SYN1b00 SYN0002 PNP0f13 (active)

[    0.425346] pnp 00:09: [mem 0xfed1c000-0xfed1ffff]

[    0.425349] pnp 00:09: [mem 0xfed10000-0xfed13fff]

[    0.425351] pnp 00:09: [mem 0xfed18000-0xfed18fff]

[    0.425353] pnp 00:09: [mem 0xfed19000-0xfed19fff]

[    0.425355] pnp 00:09: [mem 0xf0000000-0xf1ffffff]

[    0.425357] pnp 00:09: [mem 0xfed20000-0xfed3ffff]

[    0.425360] pnp 00:09: [mem 0xfed90000-0xfed8ffff disabled]

[    0.425362] pnp 00:09: [mem 0xfed45000-0xfed8ffff]

[    0.425364] pnp 00:09: [mem 0xff000000-0xffffffff]

[    0.425366] pnp 00:09: [mem 0xfee00000-0xfeefffff]

[    0.425368] pnp 00:09: [mem 0xbc000000-0xbc000fff]

[    0.425435] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved

[    0.425438] system 00:09: [mem 0xfed10000-0xfed13fff] has been reserved

[    0.425441] system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved

[    0.425444] system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved

[    0.425447] system 00:09: [mem 0xf0000000-0xf1ffffff] has been reserved

[    0.425450] system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved

[    0.425453] system 00:09: [mem 0xfed45000-0xfed8ffff] has been reserved

[    0.425456] system 00:09: [mem 0xff000000-0xffffffff] could not be reserved

[    0.425459] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved

[    0.425462] system 00:09: [mem 0xbc000000-0xbc000fff] has been reserved

[    0.425465] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)

[    0.425636] pnp 00:0a: [bus 7f]

[    0.425684] pnp 00:0a: Plug and Play ACPI device, IDs PNP0a03 (active)

[    0.425701] pnp: PnP ACPI: found 11 devices

[    0.425703] ACPI: ACPI bus type pnp unregistered

[    0.433059] PCI: max bus depth: 1 pci_try_num: 2

[    0.433092] pci 0000:00:1c.0: PCI bridge to [bus 01-01]

[    0.433097] pci 0000:00:1c.0:  bridge window [io  0x2000-0x2fff]

[    0.433103] pci 0000:00:1c.0:  bridge window [mem 0xd3400000-0xd43fffff]

[    0.433109] pci 0000:00:1c.0:  bridge window [mem 0xd0400000-0xd13fffff 64bit pref]

[    0.433117] pci 0000:00:1c.5: PCI bridge to [bus 02-02]

[    0.433120] pci 0000:00:1c.5:  bridge window [io  0x1000-0x1fff]

[    0.433127] pci 0000:00:1c.5:  bridge window [mem 0xd2400000-0xd33fffff]

[    0.433132] pci 0000:00:1c.5:  bridge window [mem 0xd1400000-0xd23fffff 64bit pref]

[    0.433141] pci 0000:00:1e.0: PCI bridge to [bus 03-03]

[    0.433176] pci 0000:00:1c.0: setting latency timer to 64

[    0.433192] pci 0000:00:1c.5: setting latency timer to 64

[    0.433201] pci 0000:00:1e.0: setting latency timer to 64

[    0.433206] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]

[    0.433208] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]

[    0.433210] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]

[    0.433213] pci_bus 0000:00: resource 7 [mem 0xbc000000-0xfeafffff]

[    0.433215] pci_bus 0000:01: resource 0 [io  0x2000-0x2fff]

[    0.433217] pci_bus 0000:01: resource 1 [mem 0xd3400000-0xd43fffff]

[    0.433219] pci_bus 0000:01: resource 2 [mem 0xd0400000-0xd13fffff 64bit pref]

[    0.433222] pci_bus 0000:02: resource 0 [io  0x1000-0x1fff]

[    0.433224] pci_bus 0000:02: resource 1 [mem 0xd2400000-0xd33fffff]

[    0.433226] pci_bus 0000:02: resource 2 [mem 0xd1400000-0xd23fffff 64bit pref]

[    0.433228] pci_bus 0000:03: resource 4 [io  0x0000-0x0cf7]

[    0.433230] pci_bus 0000:03: resource 5 [io  0x0d00-0xffff]

[    0.433232] pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]

[    0.433234] pci_bus 0000:03: resource 7 [mem 0xbc000000-0xfeafffff]

[    0.433296] NET: Registered protocol family 2

[    0.435429] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)

[    0.436353] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)

[    0.439313] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)

[    0.439683] TCP: Hash tables configured (established 524288 bind 65536)

[    0.439685] TCP reno registered

[    0.439699] UDP hash table entries: 2048 (order: 4, 65536 bytes)

[    0.439729] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)

[    0.439883] NET: Registered protocol family 1

[    0.439900] pci 0000:00:02.0: Boot video device

[    0.469872] PCI: CLS 64 bytes, default 64

[    0.469925] Unpacking initramfs...

[    0.730574] Freeing initrd memory: 11128k freed

[    0.733100] Simple Boot Flag at 0x44 set to 0x1

[    0.733571] audit: initializing netlink socket (disabled)

[    0.733585] type=2000 audit(1441699657.588:1): initialized

[    0.749845] HugeTLB registered 2 MB page size, pre-allocated 0 pages

[    0.750519] VFS: Disk quotas dquot_6.5.2

[    0.750548] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)

[    0.750628] msgmni has been set to 5515

[    0.750826] alg: No test for stdrng (krng)

[    0.750859] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)

[    0.750863] io scheduler noop registered

[    0.750864] io scheduler deadline registered

[    0.750881] io scheduler cfq registered (default)

[    0.751106] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

[    0.751127] pciehp: PCI Express Hot Plug Controller Driver version: 0.4

[    0.751129] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5

[    0.751537] intel_idle: MWAIT substates: 0x120

[    0.751539] intel_idle: v0.4 model 0x25

[    0.751541] intel_idle: lapic_timer_reliable_states 0xffffffff

[    0.751581] ERST: Table is not found!

[    0.751583] GHES: HEST is not enabled!

[    0.751646] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[    0.802085] Linux agpgart interface v0.103

[    0.802165] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset

[    0.802221] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable

[    0.802757] agpgart-intel 0000:00:00.0: detected 131072K stolen memory

[    0.802917] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000

[    0.803053] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12

[    0.809685] i8042: Detected active multiplexing controller, rev 1.1

[    0.813127] serio: i8042 KBD port at 0x60,0x64 irq 1

[    0.813135] serio: i8042 AUX0 port at 0x60,0x64 irq 12

[    0.813168] serio: i8042 AUX1 port at 0x60,0x64 irq 12

[    0.813194] serio: i8042 AUX2 port at 0x60,0x64 irq 12

[    0.813219] serio: i8042 AUX3 port at 0x60,0x64 irq 12

[    0.813354] mousedev: PS/2 mouse device common for all mice

[    0.813563] rtc_cmos 00:06: RTC can wake from S4

[    0.813705] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0

[    0.813739] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs

[    0.813782] cpuidle: using governor ladder

[    0.813820] cpuidle: using governor menu

[    0.814025] TCP cubic registered

[    0.814110] NET: Registered protocol family 10

[    0.814672] Mobile IPv6

cont./... in next post

cont. from previous post 2

dmesg final part
4

Code:

[    0.814675] NET: Registered protocol family 17

[    0.814678] Registering the dns_resolver key type

[    0.814983] PM: Hibernation image not present or could not be loaded.

[    0.814997] registered taskstats version 1

[    0.815637] rtc_cmos 00:06: setting system clock to 2015-09-08 08:07:38 UTC (1441699658)

[    0.815701] Initializing network drop monitor service

[    0.817073] Freeing unused kernel memory: 580k freed

[    0.817174] Write protecting the kernel read-only data: 6144k

[    0.819892] Freeing unused kernel memory: 644k freed

[    0.822794] Freeing unused kernel memory: 688k freed

[    0.836678] systemd-udevd[49]: starting version 215

[    0.837485] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0

[    0.847252] usbcore: registered new interface driver usbfs

[    0.847279] usbcore: registered new interface driver hub

[    0.853261] SCSI subsystem initialized

[    0.854654] usbcore: registered new device driver usb

[    0.855014] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    0.855067] ehci_hcd 0000:00:1a.0: setting latency timer to 64

[    0.855072] ehci_hcd 0000:00:1a.0: EHCI Host Controller

[    0.855099] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1

[    0.855130] ehci_hcd 0000:00:1a.0: debug port 2

[    0.859053] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported

[    0.861035] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xd4405c00

[    0.865112] libata version 3.00 loaded.

[    0.867487] tg3.c:v3.121 (November 2, 2011)

[    0.867547] tg3 0000:01:00.0: setting latency timer to 64

[    0.873640] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00

[    0.873686] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[    0.873689] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    0.873692] usb usb1: Product: EHCI Host Controller

[    0.873693] usb usb1: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd

[    0.873695] usb usb1: SerialNumber: 0000:00:1a.0

[    0.873822] hub 1-0:1.0: USB hub found

[    0.873827] hub 1-0:1.0: 3 ports detected

[    0.873927] ehci_hcd 0000:00:1d.0: setting latency timer to 64

[    0.873931] ehci_hcd 0000:00:1d.0: EHCI Host Controller

[    0.873939] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2

[    0.873971] ehci_hcd 0000:00:1d.0: debug port 2

[    0.877883] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported

[    0.877925] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xd4405800

[    0.884096] thermal LNXTHERM:00: registered as thermal_zone0

[    0.884099] ACPI: Thermal Zone [THRM] (26 C)

[    0.888269] tg3 mdio bus: probed

[    0.893581] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00

[    0.893610] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002

[    0.893612] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[    0.893615] usb usb2: Product: EHCI Host Controller

[    0.893617] usb usb2: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd

[    0.893619] usb usb2: SerialNumber: 0000:00:1d.0

[    0.893753] hub 2-0:1.0: USB hub found

[    0.893758] hub 2-0:1.0: 3 ports detected

[    0.893969] ahci 0000:00:1f.2: version 3.0

[    0.894047] ahci 0000:00:1f.2: irq 40 for MSI/MSI-X

[    0.894086] ahci: SSS flag set, parallel bus scan disabled

[    0.894128] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x3 impl SATA mode

[    0.894132] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems apst 

[    0.894137] ahci 0000:00:1f.2: setting latency timer to 64

[    0.897996] tg3 0000:01:00.0: eth0: Tigon3 [partno(BCM57780) rev 57780001] (PCI Express) MAC address 60:eb:69:8c:f1:a9

[    0.897999] tg3 0000:01:00.0: eth0: attached PHY driver [Broadcom BCM57780] (mii_bus:phy_addr=100:01)

[    0.898003] tg3 0000:01:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]

[    0.898005] tg3 0000:01:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit]

[    0.903757] scsi0 : ahci

[    0.903868] scsi1 : ahci

[    0.903954] scsi2 : ahci

[    0.904019] scsi3 : ahci

[    0.904119] ata1: SATA max UDMA/133 abar m2048@0xd4405000 port 0xd4405100 irq 40

[    0.904123] ata2: SATA max UDMA/133 abar m2048@0xd4405000 port 0xd4405180 irq 40

[    0.904125] ata3: DUMMY

[    0.904127] ata4: DUMMY

[    1.185531] usb 1-1: new high-speed USB device number 2 using ehci_hcd

[    1.221494] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

[    1.222758] ata1.00: ATA-8: WDC WD2500BEVT-22A23T0, 01.01A01, max UDMA/133

[    1.222765] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA

[    1.224194] ata1.00: configured for UDMA/133

[    1.224535] scsi 0:0:0:0: Direct-Access    ATA      WDC WD2500BEVT-2 01.0 PQ: 0 ANSI: 5

[    1.317840] usb 1-1: New USB device found, idVendor=8087, idProduct=0020

[    1.317847] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

[    1.318262] hub 1-1:1.0: USB hub found

[    1.318454] hub 1-1:1.0: 6 ports detected

[    1.429402] usb 2-1: new high-speed USB device number 2 using ehci_hcd

[    1.541372] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

[    1.541695] ata2.00: ATAPI: Optiarc DVD RW AD-7585H, KX04, max UDMA/100

[    1.542535] ata2.00: configured for UDMA/100

[    1.546070] scsi 1:0:0:0: CD-ROM            Optiarc  DVD RW AD-7585H  KX04 PQ: 0 ANSI: 5

[    1.548911] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)

[    1.548988] sd 0:0:0:0: [sda] Write Protect is off

[    1.548991] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

[    1.549008] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[    1.557145] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray

[    1.557152] cdrom: Uniform CD-ROM driver Revision: 3.20

[    1.557464] sr 1:0:0:0: Attached scsi CD-ROM sr0

[    1.561743] usb 2-1: New USB device found, idVendor=8087, idProduct=0020

[    1.561750] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0

[    1.562137] hub 2-1:1.0: USB hub found

[    1.562198] hub 2-1:1.0: 8 ports detected

[    1.630690]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >

[    1.631885] sd 0:0:0:0: [sda] Attached SCSI disk

[    1.632510] sd 0:0:0:0: Attached scsi generic sg0 type 0

[    1.632631] sr 1:0:0:0: Attached scsi generic sg1 type 5

[    1.633419] usb 1-1.5: new high-speed USB device number 3 using ehci_hcd

[    1.727184] usb 1-1.5: New USB device found, idVendor=058f, idProduct=6366

[    1.727193] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[    1.727199] usb 1-1.5: Product: Mass Storage Device

[    1.727203] usb 1-1.5: Manufacturer: Generic

[    1.727207] usb 1-1.5: SerialNumber: 058F63666433

[    1.729079] Initializing USB Mass Storage driver...

[    1.729225] Refined TSC clocksource calibration: 2128.000 MHz.

[    1.729231] Switching to clocksource tsc

[    1.729264] scsi4 : usb-storage 1-1.5:1.0

[    1.729392] usbcore: registered new interface driver usb-storage

[    1.729394] USB Mass Storage support registered.

[    1.833402] usb 2-1.2: new low-speed USB device number 3 using ehci_hcd

[    1.929735] usb 2-1.2: New USB device found, idVendor=15d9, idProduct=0a4c

[    1.929742] usb 2-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0

[    1.929748] usb 2-1.2: Product:  USB OPTICAL MOUSE

[    1.933672] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input1

[    1.933902] generic-usb 0003:15D9:0A4C.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.2/input0

[    1.933935] usbcore: registered new interface driver usbhid

[    1.933941] usbhid: USB HID core driver

[    2.857897] scsi 4:0:0:0: Direct-Access    Multiple Card  Reader    1.00 PQ: 0 ANSI: 0

[    2.859715] sd 4:0:0:0: Attached scsi generic sg2 type 0

[    3.238084] sd 4:0:0:0: [sdb] Attached SCSI removable disk

[    3.316291] PM: Starting manual resume from disk

[    3.316294] PM: Hibernation image partition 8:6 present

[    3.316296] PM: Looking for hibernation image.

[    3.345813] PM: Image not found (code -22)

[    3.345817] PM: Hibernation image not present or could not be loaded.

[    3.697112] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)

[    5.887098] systemd-udevd[274]: starting version 215

[    7.073013] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4

[    7.096177] iTCO_vendor_support: vendor-support=0

[    7.107459] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/PNP0C0C:00/input/input2

[    7.107465] ACPI: Power Button [PWRB]

[    7.107524] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/PNP0C0D:00/input/input3

[    7.107594] ACPI: Lid Switch [LID0]

[    7.107641] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/PNP0C0E:00/input/input4

[    7.107644] ACPI: Sleep Button [SLPB]

[    7.107692] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5

[    7.107695] ACPI: Power Button [PWRF]

[    7.110101] ACPI: Requesting acpi_cpufreq

[    7.169607] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07

[    7.169700] iTCO_wdt: Found a HM55 TCO device (Version=2, TCOBASE=0x0460)

[    7.169765] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)

[    7.191907] wmi: Mapper loaded

[    7.200649] ACPI: resource 0000:00:1f.3 [io  0x3000-0x301f] conflicts with ACPI region SMBI [io 0x3000-0x300f]

[    7.200652] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver

[    7.228110] ACPI: AC Adapter [ACAD] (off-line)

[    7.229961] ACPI: Battery Slot [BAT1] (battery present)

[    7.467530] intel ips 0000:00:1f.6: No CPUID match found.

[    7.467533] intel ips 0000:00:1f.6: IPS not supported on this CPU

[    7.521054] [drm] Initialized drm 1.1.0 20060810

[    7.649123] input: PC Speaker as /devices/platform/pcspkr/input/input6

[    7.839666] Error: Driver 'pcspkr' is already registered, aborting...

[    7.942000] i915 0000:00:02.0: setting latency timer to 64

[    7.962433] i915 0000:00:02.0: irq 41 for MSI/MSI-X

[    7.962443] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).

[    7.962444] [drm] Driver supports precise vblank timestamp query.

[    7.962487] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem

[    8.249061] acer_wmi: Acer Laptop ACPI-WMI Extras

[    8.249083] acer_wmi: Function bitmap for Communication Button: 0x1

[    8.249248] acer_wmi: Brightness must be controlled by generic video driver

[    8.249907] input: Acer WMI hotkeys as /devices/virtual/input/input7

[    8.420915] fbcon: inteldrmfb (fb0) is primary device

[    8.615916] psmouse serio2: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000

[    8.662356] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input8

[    8.753983] Console: switching to colour frame buffer device 170x48

[    8.761470] fb0: inteldrmfb frame buffer device

[    8.761473] drm: registered panic notifier

[    8.762906] acpi device:01: registered as cooling_device2

[    8.763135] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input9

[    8.763180] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)

[    8.763249] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0

[    8.778321] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)

[    8.778546] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X

[    8.778586] snd_hda_intel 0000:00:1b.0: setting latency timer to 64

[    9.011170] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10

[    9.047518] HDMI status: Codec=3 Pin=4 Presence_Detect=0 ELD_Valid=0

[    9.047680] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11

[    9.047857] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12

[    9.047925] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13

[  10.090607] Adding 4535292k swap on /dev/sda6.  Priority:-1 extents:1 across:4535292k 

[  10.362882] EXT4-fs (sda5): re-mounted. Opts: (null)

[  29.202431] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro

[  29.634406] loop: module loaded

[  29.677212] fuse init (API version 7.17)

[  30.262181] tg3 0000:01:00.0: irq 43 for MSI/MSI-X

[  30.287105] ADDRCONF(NETDEV_UP): eth0: link is not ready

[  30.867757] RPC: Registered named UNIX socket transport module.

[  30.867760] RPC: Registered udp transport module.

[  30.867762] RPC: Registered tcp transport module.

[  30.867764] RPC: Registered tcp NFSv4.1 backchannel transport module.

[  30.886054] tg3 0000:01:00.0: eth0: Link is down

[  30.953803] FS-Cache: Loaded

[  31.025005] FS-Cache: Netfs 'nfs' registered for caching

[  31.123309] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

[  32.296857] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input14

[  37.921417] Bluetooth: Core ver 2.16

[  37.921446] NET: Registered protocol family 31

[  37.921450] Bluetooth: HCI device and connection manager initialized

[  37.921459] Bluetooth: HCI socket layer initialized

[  37.921462] Bluetooth: L2CAP socket layer initialized

[  37.921471] Bluetooth: SCO socket layer initialized

[  39.752453] systemd-logind[2388]: New seat seat0.

[  39.752941] systemd-logind[2388]: Watching system buttons on /dev/input/event5 (Power Button)

[  39.753018] systemd-logind[2388]: Watching system buttons on /dev/input/event9 (Video Bus)

[  39.753092] systemd-logind[2388]: Watching system buttons on /dev/input/event2 (Power Button)

[  39.753179] systemd-logind[2388]: Watching system buttons on /dev/input/event3 (Lid Switch)

[  39.753252] systemd-logind[2388]: Watching system buttons on /dev/input/event4 (Sleep Button)

[  44.884146] systemd-logind[2388]: Failed to start user service: Unknown unit: user@113.service

[  44.925846] systemd-logind[2388]: New session c1 of user Debian-gdm.

[  68.900156] systemd-logind[2388]: Failed to start user service: Unknown unit: user@1000.service

[  69.031137] systemd-logind[2388]: New session 1 of user tuddy.

[  130.802957] usb 1-1.2: new high-speed USB device number 4 using ehci_hcd

[  130.908146] usb 1-1.2: New USB device found, idVendor=0d7d, idProduct=1620

[  130.908153] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[  130.908159] usb 1-1.2: Product: USB DISK Pro    

[  130.908164] usb 1-1.2: Manufacturer:        

[  130.908168] usb 1-1.2: SerialNumber: 07521802236E

[  130.909155] scsi5 : usb-storage 1-1.2:1.0

[  131.907170] scsi 5:0:0:0: Direct-Access              USB DISK Pro    PMAP PQ: 0 ANSI: 0 CCS

[  131.907820] scsi 5:0:0:1: Direct-Access              USB DISK Pro    PMAP PQ: 0 ANSI: 0 CCS

[  131.910533] sd 5:0:0:0: Attached scsi generic sg3 type 0

[  131.911424] sd 5:0:0:1: Attached scsi generic sg4 type 0

[  133.032402] sd 5:0:0:0: [sdc] 1000448 512-byte logical blocks: (512 MB/488 MiB)

[  133.032765] sd 5:0:0:1: [sdd] 2880 512-byte logical blocks: (1.47 MB/1.40 MiB)

[  133.033255] sd 5:0:0:0: [sdc] Write Protect is off

[  133.033261] sd 5:0:0:0: [sdc] Mode Sense: 23 00 00 00

[  133.033748] sd 5:0:0:1: [sdd] Write Protect is off

[  133.033754] sd 5:0:0:1: [sdd] Mode Sense: 23 94 00 00

[  133.034305] sd 5:0:0:0: [sdc] No Caching mode page found

[  133.034312] sd 5:0:0:0: [sdc] Assuming drive cache: write through

[  133.034905] sd 5:0:0:1: [sdd] No Caching mode page found

[  133.034908] sd 5:0:0:1: [sdd] Assuming drive cache: write through

[  133.039349] sd 5:0:0:0: [sdc] No Caching mode page found

[  133.039357] sd 5:0:0:0: [sdc] Assuming drive cache: write through

[  133.039887] sd 5:0:0:1: [sdd] No Caching mode page found

[  133.039893] sd 5:0:0:1: [sdd] Assuming drive cache: write through

[  133.040619]  sdc: sdc1

[  133.041366]  sdd:

[  133.045723] sd 5:0:0:1: [sdd] No Caching mode page found

[  133.045730] sd 5:0:0:1: [sdd] Assuming drive cache: write through

[  133.045736] sd 5:0:0:1: [sdd] Attached SCSI removable disk

[  133.046981] sd 5:0:0:0: [sdc] No Caching mode page found

[  133.046989] sd 5:0:0:0: [sdc] Assuming drive cache: write through

[  133.046995] sd 5:0:0:0: [sdc] Attached SCSI removable disk

[  385.614990] FAT-fs (sdc1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

Hi...

The command for rfkill was entered incorrectly. Copy and past only what you see in the box below... ;)

Code:

rfkill list

Please also post the results for...

Code:

lsmod

Also, just to confirm, were all the steps you followed in the instructions successful? Did you receive any error messages? If so, what were they?

Thanks! :)

Sorry but I still get the same response to rfkill list -> bash: rfkill: command not found. I know it is there because ls -l /dev/rfkill shows it is.

Code:

tuddy@tycornel:~$ rfkill list

bash: rfkill: command not found

tuddy@tycornel:~$ lsmod

Module                  Size  Used by

bluetooth            119455  0 

binfmt_misc            12957  1 

uinput                17440  1 

nfsd                  216181  2 

nfs                  308353  0 

nfs_acl                12511  2 nfs,nfsd

auth_rpcgss            37143  2 nfs,nfsd

fscache                36739  1 nfs

lockd                  67306  2 nfs,nfsd

sunrpc                173730  6 lockd,auth_rpcgss,nfs_acl,nfs,nfsd

fuse                  62012  1 

loop                  22641  0 

snd_hda_codec_hdmi    30824  1 

snd_hda_codec_realtek  188851  1 

joydev                17266  0 

snd_hda_intel          26259  2 

snd_hda_codec          78031  3 snd_hda_intel,snd_hda_codec_realtek,snd_hda_codec_hdmi

snd_hwdep              13186  1 snd_hda_codec

i915                  378651  2 

snd_pcm                68083  3 snd_hda_codec,snd_hda_intel,snd_hda_codec_hdmi

snd_page_alloc        13003  2 snd_pcm,snd_hda_intel

acer_wmi              26081  0 

sparse_keymap          12760  1 acer_wmi

coretemp              12898  0 

snd_timer              22917  1 snd_pcm

rfkill                19012  3 acer_wmi,bluetooth

drm_kms_helper        31370  1 i915

drm                  183952  3 drm_kms_helper,i915

snd                    52893  11 snd_timer,snd_pcm,snd_hwdep,snd_hda_codec,snd_hda_intel,snd_hda_codec_realtek,snd_hda_codec_hdmi

psmouse                69265  0 

pcspkr                12579  0 

i2c_i801              16870  0 

i2c_algo_bit          12841  1 i915

soundcore              13065  1 snd

i2c_core              23876  5 i2c_algo_bit,i2c_i801,drm,drm_kms_helper,i915

evdev                  17562  26 

serio_raw              12931  0 

iTCO_wdt              17081  0 

iTCO_vendor_support    12704  1 iTCO_wdt

intel_ips              17650  0 

battery                13146  0 

wmi                    13243  1 acer_wmi

shpchp                31293  0 

acpi_cpufreq          12935  1 

mperf                  12453  1 acpi_cpufreq

video                  17683  1 i915

ac                    12624  0 

power_supply          13475  2 ac,battery

button                12937  1 i915

processor              28149  1 acpi_cpufreq

ext4                  350804  1 

crc16                  12343  2 ext4,bluetooth

jbd2                  62115  1 ext4

mbcache                13114  1 ext4

usbhid                36418  0 

hid                    81372  1 usbhid

usb_storage            43870  0 

sg                    25874  0 

sd_mod                36136  3 

crc_t10dif            12348  1 sd_mod

sr_mod                21899  0 

cdrom                  35401  1 sr_mod

thermal                17383  0 

thermal_sys            18040  3 thermal,processor,video

broadcom              13032  0 

ahci                  24997  2 

libahci                22941  1 ahci

ehci_hcd              40249  0 

libata                140630  2 libahci,ahci

usbcore              128741  4 ehci_hcd,usb_storage,usbhid

usb_common            12354  1 usbcore

scsi_mod              162321  5 libata,sr_mod,sd_mod,sg,usb_storage

tg3                  119064  0 

libphy                19057  2 tg3,broadcom

Regarding the instructions in https://wiki.debian.org/wl
I knew that /etc/apt/sources.list was OK because I had had no problems during the update, upgrade process. There were warnings about some drivers or certificates that were not going to be supported in future. I did not understand everything as it flashed past.
There were no reported errors during step 2. apt-get install linux-headers-$(uname .... I che.cked carefully that I had correctly entered the string.
No errors either as I modprobe -r b44 b43 b43legacy ssb brcmsmac. However, modprobe wl responded FATAL not found.
I proceeded no futher and would not really have attempted to configure wireless interface unaided.

Thank you for your time :)

Try the brcmsmac before messing about with the broadcom proprietary driver:

https://wiki.debian.org/brcm80211

As per the wiki page section 1 "installation", ensure that the firmware-brcm80211 package is installed. Then remove and reinsert the kernel module.

This should give you a wlan interface which you can configure as per usual.

modprobe -r removes modules from being loaded. In your lsmod and dmesg output I saw now wireless drivers. Perhaps modprobe without the -r would help

# modprobe b43
$ dmesg | tail -n 30

The other linked url seemed to suggest that ssb and wl conflict so don't have both loaded at the same time.

$ lsmod

Otherwise tg3 seems to be functioning, which is probably your ethernet.

http://www.linuxwireless.org/en/users/Drivers/b43/

Seems to suggest the your card uses the wl + brcm80211 driver.

# modprobe -r b43 ssb
# modprobe brcm80211 wl
# dmesg | tail -n 50

14e4:4357 - Broadcom Corporation BCM43225 802.11b/g/n

You might also be missing firmware.

# apt-get install firmware-linux-free firmware-linux-nonfree

Quote:

Originally Posted by Shadow_7 (Post 5417534)

You might also be missing firmware.

That's what I'm thinking, too. ;)

Regards...

Thank you Shadow_7

Quote:

You might also be missing firmware.
# apt-get install firmware-linux-free firmware-linux-nonfree

I did this first successfully - no problems. Then, I attempted to understand
http://http://www.linuxwireless.org/...s/Drivers/b43/ and tried to link your comments Shadow_7 about driver conflicts. This looked like a way of avoiding my ignorance:

Quote:

Ubuntu/Debian
In recent versions of Ubuntu and Debian, installing the firmware-b43-installer package will handle everything for you:
Toggle line numbers
1 sudo apt-get install firmware-b43-installer
You will be asked to automatically fetch and install the firmware into the right location. Again, you will need an internet connection.

:confused: It installed but didn't ask me anything and I should apt-get purge to remove what ever it has installed.

Thank you cynwulf :)

Quote:

Try the brcmsmac before messing about with the broadcom proprietary driver:

https://wiki.debian.org/brcm80211
This appeared to install correctly, but after a reboot nothing has changed :(

Code:

# dmesg | tail -n 50

[    7.721254] fb0: inteldrmfb frame buffer device

[    7.721256] drm: registered panic notifier

[    7.722656] acpi device:01: registered as cooling_device2

[    7.722894] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input9

[    7.722947] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)

[    7.723021] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0

[    7.738282] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)

[    7.738384] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X

[    7.738426] snd_hda_intel 0000:00:1b.0: setting latency timer to 64

[    8.379888] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10

[    8.427882] HDMI status: Codec=3 Pin=4 Presence_Detect=0 ELD_Valid=0

[    8.428112] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11

[    8.428450] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12

[    8.428580] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13

[    9.581630] Adding 4535292k swap on /dev/sda6.  Priority:-1 extents:1 across:4535292k 

[    9.803178] EXT4-fs (sda5): re-mounted. Opts: (null)

[  28.918933] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro

[  29.358555] loop: module loaded

[  29.401466] fuse init (API version 7.17)

[  30.017980] tg3 0000:01:00.0: irq 43 for MSI/MSI-X

[  30.042727] ADDRCONF(NETDEV_UP): eth0: link is not ready

[  30.859662] RPC: Registered named UNIX socket transport module.

[  30.859667] RPC: Registered udp transport module.

[  30.859670] RPC: Registered tcp transport module.

[  30.859672] RPC: Registered tcp NFSv4.1 backchannel transport module.

[  30.878178] FS-Cache: Loaded

[  30.889520] tg3 0000:01:00.0: eth0: Link is down

[  30.949160] FS-Cache: Netfs 'nfs' registered for caching

[  30.970729] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).

[  32.032308] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input14

[  38.177559] Bluetooth: Core ver 2.16

[  38.177577] NET: Registered protocol family 31

[  38.177579] Bluetooth: HCI device and connection manager initialized

[  38.177582] Bluetooth: HCI socket layer initialized

[  38.177584] Bluetooth: L2CAP socket layer initialized

[  38.177588] Bluetooth: SCO socket layer initialized

[  39.133386] systemd-logind[2279]: New seat seat0.

[  39.133865] systemd-logind[2279]: Watching system buttons on /dev/input/event5 (Power Button)

[  39.133942] systemd-logind[2279]: Watching system buttons on /dev/input/event9 (Video Bus)

[  39.134014] systemd-logind[2279]: Watching system buttons on /dev/input/event2 (Power Button)

[  39.134083] systemd-logind[2279]: Watching system buttons on /dev/input/event3 (Lid Switch)

[  39.134154] systemd-logind[2279]: Watching system buttons on /dev/input/event4 (Sleep Button)

[  44.466528] systemd-logind[2279]: Failed to start user service: Unknown unit: user@113.service

[  44.504799] systemd-logind[2279]: New session c1 of user Debian-gdm.

[  74.444141] systemd-logind[2279]: Failed to start user service: Unknown unit: user@1000.service

[  74.492205] systemd-logind[2279]: New session 1 of user tuddy.

[  383.740420] tg3 0000:01:00.0: eth0: Link is up at 100 Mbps, full duplex

[  383.740428] tg3 0000:01:00.0: eth0: Flow control is on for TX and on for RX

[  383.741224] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[  394.306927] eth0: no IPv6 routers present

I tried these searches from https://wiki.debian.org/WiFi/HowToUse#Command_Line

Code:

# modprobe wl

modprobe: FATAL: Module wl not found.

# modprobe brcm80211

modprobe: FATAL: Module brcm80211 not found.

# ip a

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN group default 

    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00

    inet 127.0.0.1/8 scope host lo

    inet6 ::1/128 scope host 

      valid_lft forever preferred_lft forever

2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000

    link/ether 60:eb:69:8c:f1:a9 brd ff:ff:ff:ff:ff:ff

    inet 192.168.1.8/24 brd 192.168.1.255 scope global eth0

    inet6 fe80::62eb:69ff:fe8c:f1a9/64 scope link 

      valid_lft forever preferred_lft forever

# iwconfig

lo        no wireless extensions.



eth0      no wireless extensions.



# ip link set wlan0 up

Cannot find device "wlan0"

# iwlist scan

lo        Interface doesn't support scanning.



eth0      Interface doesn't support scanning.

I apologize for not responding last night. I was attending a meeting and we are 6-9 hrs ahead of you in the Americas
kestreltowers

https://wiki.debian.org/brcm80211

Posted by someone else mentions the brcm80211 conflict with b43.

# apt-get install firmware-brcm80211

As mentioned in that link.

# modprobe brcmsmac
(or brcmfmac, the smac is the software MAC version)

Seems to be the actual module/driver name in the kernel, my mistake.

https://wireless.wiki.kernel.org/en/...vers/brcm80211

With additional details.

And broadcoms download page.

https://www.broadcom.com/support/?gid=1

Which does 43224, but not 43225.

Mentions of wl here: https://wiki.debian.org/wl
But I can't find anything meaningful in debian 8 so probably dated information.

... in short ...

# apt-get install firmware-brcm80211
# modprobe brcmsmac
$ dmesg | tail -n 30

Thank you, Shadow_7. You must be thinking that we are simply going in circles. I wonder if I should find out how to remove Debian installation on this partition and start again with a distro that doesn't have these wifi network issues?

Quote:

# apt-get install firmware-brcm80211
# modprobe brcmsmac
$ dmesg | tail -n 30

I did that and this is the dmest result:

Code:

dmesg | tail -n 30

[  39.135879] systemd-logind[2420]: Watching system buttons on /dev/input/event3 (Lid Switch)

[  39.135997] systemd-logind[2420]: Watching system buttons on /dev/input/event4 (Sleep Button)

[  44.511340] systemd-logind[2420]: Failed to start user service: Unknown unit: user@113.service

[  44.553229] systemd-logind[2420]: New session c1 of user Debian-gdm.

[  67.151057] systemd-logind[2420]: Failed to start user service: Unknown unit: user@1000.service

[  67.216538] systemd-logind[2420]: New session 1 of user tuddy.

[  202.712176] cfg80211: Calling CRDA to update world regulatory domain

[  202.798818] brcmsmac 0000:02:00.0: bus 2 slot 0 func 0 irq 5

[  202.798874] brcmsmac 0000:02:00.0: setting latency timer to 64

[  202.844605] cfg80211: World regulatory domain updated:

[  202.844610] cfg80211:    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[  202.844614] cfg80211:    (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[  202.844619] cfg80211:    (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[  202.844622] cfg80211:    (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)

[  202.844626] cfg80211:    (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)

[  202.844629] cfg80211:    (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)

[  202.844633] cfg80211:    (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)

[  202.844637] cfg80211:    (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)

[  202.844640] cfg80211:    (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)

[  202.876993] brcmsmac 0000:02:00.0: firmware: agent loaded brcm/bcm43xx-0.fw into memory

[  202.895942] brcmsmac 0000:02:00.0: firmware: agent loaded brcm/bcm43xx_hdr-0.fw into memory

[  202.943851] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

[  202.944954] cfg80211: Calling CRDA for country: US

[  202.948676] cfg80211: Regulatory domain changed to country: US

[  202.948680] cfg80211:    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[  202.948684] cfg80211:    (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm)

[  202.948687] cfg80211:    (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm)

[  202.948690] cfg80211:    (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm)

[  202.948693] cfg80211:    (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm)

[  202.948696] cfg80211:    (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)

Best regards,
kestreltowers :newbie: