Laptop as a router
 

i am using Ubuntu 7.04.
How do i setup my laptop to function as a wirelss router?
So that other laptop can receive signal from the 1st laptop and connect to the internet.

thank you very much

Short answer... You dont, you go spend the 15$ a cheap router would cost and use it to share the internet and not have headaches for the rest of your surfing days.

If your avoiding the router cause you have dial-up... Forget it. Dial-ups to crappy and slow to mess around with all the fuss setting it up. It also violates the terms of service for every dial-up carrier I've ever seen. They all say ONE computer at a time.

Other than that. You'd be creating an ad-hoc network if the network cards are capable. And one computer would have to be running properly configured proxy software to share the net.

I could go into severe details on how to create the ad-hoc and which proxy software and how to config it but...
Out of curiosity I typed just 2 words into google and got no less than 25 threads on ubuntu forums, just-linux.com and a few other sites in which people have literally beaten this topic into the ground with ways to do it, so it's ridiculous to type it again here.

^ seconded!

Buy an inexpensive wireless router/Access Point and put your laptop to a better use. Make a music server or a digital picture frame or anything.. There are TONS of better ways to utilize that old laptop than turning it into a router.

Thirded! Just because it is possible to do something doesn't mean it makes any sense to do it. If you just want to do it as a "learning experience", then there is no point in having someone here tell you how to do it - you can dig up the necessary info yourself.

I've done something similar exactly ONCE in order to do a one-time net install of Debian on an old system. It was much more trouble than it was worth. Also, not all network card drivers are capable of doing what you want.

I give you a scenario.

wireless router is upstairs. I have no cable access there.
When I need to install linux it need internet access which I can't provide.
I have tried putting wireless router in my room attach cable to it.
But it wont work like a router on a wireless link.

It doesn't consider wireless link as "UP LINK".
So it doesnt forward traffic to router up stairs.

Wireless repeater
 

Hello.
I know that some wireless access point can act as a repeater. At least some of the DLink AP's are. I remember DLink DWL-900 and DWL-2000 could do that.

i just need a laptop to function as a router to test my WLAN card.
it aint worth investing €15 on something which i will only use 1x

simple wireless router & ip command
 

i am using Ubuntu 7.10

i have 2 laptops, A and B, both with WLAN cards.
A is connected to the internet through an ethernet cable.
how can i make A function as an access point so that B can receive the signal from A and surf the internet?

i use "Create New Wireless Network", but it keeps failing. It just reverts back to itz wired connection.

p/s - pls DONT ask me to buy a new router

thank you.

Additional niformation : you can say that i want to turn my laptop into a wireless hotspot

You must first check if the wireless card suports AP mode or "master mode" and if so enable it and configure.
Then all you have to do is enable forwarding between the ethernet and the wireless card.

check gentoo-wiki.com/HOWTO_Building_a_Wireless_Access_Point

it has AP mode.
So what procedure whould i take?

thank you

siple wireless router
 

i am trying to link 2 comps using Ad-Hoc.
http://www.wlug.org.nz/WirelessSetupNotes

Ad-Hoc Mode
Mode: Ad-Hoc
Channel: 6
ESSID: wlug-test
Network: 10.10.10.0/24, this computer will be 10.10.10.1, Remote Computer will be 10.10.10.254

The above is and example for a step. My question is, how do i determine my Network values?

thank you

If I understand correctly what you need is to locate the IP for each machine. There are a number of tools to do so. I bet your distro has some kind of graphical tool to set up the network and they IP's should be visible somewhere around there.

In any case, you could also use ifconfig, which is a command line tool.

Log in as root user on a terminal or vt, and run ifconfig. It should work all the network interfaces available on the machine along with their IP direction.

well I posted a link:
gentoo-wiki.com/HOWTO_Building_a_Wireless_Access_Point
Try to get the info you need from there. It's very easy to follow

It realy deppends on your distribution and the tools you use to configure.
I guess you use iwconfig.
If you have the right drivers and the card is working properly by using iwconfig you can enable master mode and the other options:
check out this link .
linuxcommand.org/man_pages/iwconfig8.html
see iwconfig mode options.

if the card is configured correctly
set the IP adresses for the ethernet and the wireless card,
enable ip forward
echo "1" > /proc/sys/net/ipv4/ip_forward
set the policy to allow forward traffic
/sbin/iptables -P FORWARD ALLOW
enable masquerade for the wlan card
/sbin/iptables -t nat -A POSTROUTING -o wlan0 -j MASQUERADE

Or as the normal user you should be able to get at it by specifying the path to the ifconfig cmd:

/sbin/ifconfig

simple wireless router & ip command
 

i am using Ubuntu 7.10
my laptop is connected to a wireless to a host.
how can i check the ip address of the host from my laptop?
tq

Ad-Hoc problem
 

i have 2 laptops and both have WLAN.
Laptop A has Ubuntu 7.10
Laptop B has Ubuntu 7.04

i am trying to link the 2 laptops using Ad-Hoc
Laptop A is the transmitter and B is the receiver

in A, i type "ifconfig eth2 10.10.10.1 netmask 255.255.255.0 broadcast 10.10.10.255 up"

B is now connected to "Test"
However, when i type "ping 10.10.10.254", it says:-
From xxx.xxx.x.xxx icmp_seq=2 Desination Host unreachable
From xxx.xxx.x.xxx icmp_seq=3 Desination Host unreachable
From xxx.xxx.x.xxx icmp_seq=4 Desination Host unreachable
and so on until i hot Ctrl + C

What is the problem?
pls help me

p/s :- i am used this website for instructions.
http://www.wlug.org.nz/WirelessSetupNotes

thank you

Please post your thread in only one forum. Posting a single thread in the most relevant forum will make it easier for members to help you and will keep the discussion in one place. This thread is being closed because it is a duplicate.

If you want to find the IP of your own machine, then use the command "ifconfig". If you want the IP of the AP, then you might want to start with the output of "route" (we assume that the AP is the default router for your network).

i see many adresses. Which one is my ip?
What is the route command?

tq

is AP and master mode the same?
just to be sure, how do i check if i have it?

tq

you may use 'iwconfig' to query your wlan device ,then one of them is built ad-hoc site , another will be search for by 'iwconfig xxx essid any'.

Please post your thread in only one forum. Posting a single thread
in the most relevant forum will make it easier for members to help
you and will keep the discussion in one place.


I merged your five threads on the same topic into one, and would
ask you to revisit our rules that you agreed to when signing up,
and stop that annoying behaviour.



Cheers,
Tink