LinuxQuestions.org - Restart Problem

- Linux - Newbie (https://www.linuxquestions.org/questions/linux-newbie-8/)

- - Restart Problem (https://www.linuxquestions.org/questions/linux-newbie-8/restart-problem-781431/)

Hi guys i m using sun server (model 4170) for virtualisation.
Which has VM server 2.2 (oracle linux distribution) install on it.

Whenever i fire init 6 or reboot command .it doesnt restart.

Please find output of /etc/inittab file .

Code:



[root@OFSMUW-VS-58 iotest]# cat /etc/inittab

#

# inittab      This file describes how the INIT process should set up

#              the system in a certain run-level.

#

# Author:      Miquel van Smoorenburg, <miquels@drinkel.nl.mugnet.org>

#              Modified for RHS Linux by Marc Ewing and Donnie Barnes

#



# Default runlevel. The runlevels used by RHS are:

#  0 - halt (Do NOT set initdefault to this)

#  1 - Single user mode

#  2 - Multiuser, without NFS (The same as 3, if you do not have networking)

#  3 - Full multiuser mode

#  4 - unused

#  5 - X11

#  6 - reboot (Do NOT set initdefault to this)

#

id:3:initdefault:



# System initialization.

si::sysinit:/etc/rc.d/rc.sysinit



l0:0:wait:/etc/rc.d/rc 0

l1:1:wait:/etc/rc.d/rc 1

l2:2:wait:/etc/rc.d/rc 2

l3:3:wait:/etc/rc.d/rc 3

l4:4:wait:/etc/rc.d/rc 4

l5:5:wait:/etc/rc.d/rc 5

l6:6:wait:/etc/rc.d/rc 6



# Trap CTRL-ALT-DELETE

ca::ctrlaltdel:/sbin/shutdown -t3 -r now



# When our UPS tells us power has failed, assume we have a few minutes

# of power left.  Schedule a shutdown for 2 minutes from now.

# This does, of course, assume you have powerd installed and your

# UPS connected and working correctly.

pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting Down"



# If power was restored before the shutdown kicked in, cancel it.

pr:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown Cancelled"





# Run gettys in standard runlevels

co:2345:respawn:/sbin/agetty xvc0 9600 vt100-nav

1:2345:respawn:/sbin/mingetty tty1

2:2345:respawn:/sbin/mingetty tty2

3:2345:respawn:/sbin/mingetty tty3

4:2345:respawn:/sbin/mingetty tty4

5:2345:respawn:/sbin/mingetty tty5

6:2345:respawn:/sbin/mingetty tty6



# Run xdm in runlevel 5

x:5:respawn:/etc/X11/prefdm -nodaemon



# Run a getty on the serial console

Hi,
1) Is there any error while you issue the command? if so please list it out.
2) If not, please give me the last 10 to 15 lines of dmesg capture.

3) Is there a problem with init 0 or only with init 6?

init 6 or reboot should restart the machine but it is not happening

last few lines for dmesg

Code:

vlan225: topology change detected, propagating

vlan225: port 1(bond0.225) entering forwarding state

vlan226: topology change detected, propagating

vlan226: port 1(bond1.226) entering forwarding state

e1000e: eth3 NIC Link is Down

bonding: bond1: link status definitely down for interface eth3, disabling it

igb: eth7: igb_watchdog_task: NIC Link is Down

bonding: bond1: link status definitely down for interface eth7, disabling it

e1000e: eth1 NIC Link is Down

igb: eth5: igb_watchdog_task: NIC Link is Down

bonding: bond0: link status definitely down for interface eth1, disabling it

bonding: bond0: link status definitely down for interface eth5, disabling it

e1000e: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

bonding: bond1: link status definitely up for interface eth3.

e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

bonding: bond0: link status definitely up for interface eth1.

igb: eth5: igb_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

igb: eth7: igb_watchdog_task: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

bonding: bond0: link status definitely up for interface eth5.

bonding: bond1: link status definitely up for interface eth7.

Hi

1) I want the capture after issuing init 6?
2) Did you check the same with other users?
3) Try stopping all Ethernet interfaces and then issuing reboot or init 6.
4) Please provide me capture of ps -ax after init 6.