LinuxQuestions.org
Download your favorite Linux distribution at LQ ISO.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Newbie
User Name
Password
Linux - Newbie This Linux forum is for members that are new to Linux.
Just starting out and have a question? If it is not in the man pages or the how-to's this is the place!

Notices


Reply
  Search this Thread
Old 09-08-2009, 05:20 PM   #1
jimtino
LQ Newbie
 
Registered: Sep 2009
Posts: 3

Rep: Reputation: 0
PCMCIA Ethernet Card not recoginized


I've just "repurposed" an old HP omnibook 4150 with ubuntu 9.10. I am very new to the world of linux. Can someone take the time to walk me through the diagnostic steps to figure this out?

The ethernet card is a 3com 3ccfem556--apparently this is supported by an "ep driver"?

Here is the output from lspcmcia and lspci:

jimtino@jimtino-laptop:~$ lspcmcia
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:00:04.0)
Socket 0 Device 0: [-- no driver --] (bus ID: 0.0)
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:00:04.1)
jimtino@jimtino-laptop:~$ lspci
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:04.0 CardBus bridge: Texas Instruments PCI1220 (rev 02)
00:04.1 CardBus bridge: Texas Instruments PCI1220 (rev 02)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
01:00.0 VGA compatible controller: Neomagic Corporation NM2200 [MagicGraph 256AV] (rev 12)
01:00.1 Multimedia audio controller: Neomagic Corporation NM2200 [MagicMedia 256AV Audio] (rev 12)
jimtino@jimtino-laptop:~$

This is what happens when I type ifconfig up commands:

jimtino@jimtino-laptop:~$ sudo ifconfig wlan0 up
[sudo] password for jimtino:
wlan0: ERROR while getting interface flags: No such device
jimtino@jimtino-laptop:~$ ifconfig eth0 up
eth0: ERROR while getting interface flags: No such device

Thanks,

Jim
 
Old 09-09-2009, 01:54 AM   #2
Drakeo
Senior Member
 
Registered: Jan 2008
Location: Urbana IL
Distribution: Slackware, Slacko,
Posts: 3,154
Blog Entries: 3

Rep: Reputation: 340Reputation: 340Reputation: 340Reputation: 340
this is a very old note book you will have to go into setup (bios) and set up your pcimca card. while your in there set bios to none windows or none O/S.
I had the same problem. I believe I had to set my pcmcia slot to 16 bit in bios.
Then linux read and loaded the card. Unlike M$ linux does not run bios it only reads them.
good luck.
you may want to type dmesg and see if pcmcia is even being loaded.
 
Old 09-09-2009, 11:40 AM   #3
jimtino
LQ Newbie
 
Registered: Sep 2009
Posts: 3

Original Poster
Rep: Reputation: 0
DMESG Output

OK, thanks. How do I disable M$ in the bios? Here's my output from dmesg:


[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0800 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000040e5800 (usable)
[ 0.000000] BIOS-e820: 00000000040e5800 - 00000000040efc00 (ACPI data)
[ 0.000000] BIOS-e820: 00000000040efc00 - 00000000040ffc00 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000040ffc00 - 0000000010000000 (usable)
[ 0.000000] BIOS-e820: 00000000ffff0800 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.1 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
[ 0.000000] last_pfn = 0x10000 max_arch_pfn = 0x100000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009f800 (usable)
[ 0.000000] modified: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000f0800 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 00000000040e5800 (usable)
[ 0.000000] modified: 00000000040e5800 - 00000000040efc00 (ACPI data)
[ 0.000000] modified: 00000000040efc00 - 00000000040ffc00 (ACPI NVS)
[ 0.000000] modified: 00000000040ffc00 - 0000000010000000 (usable)
[ 0.000000] modified: 00000000ffff0800 - 0000000100000000 (reserved)
[ 0.000000] kernel direct mapping tables up to 10000000 @ 10000-15000
[ 0.000000] RAMDISK: 039a2000 - 040d4f80
[ 0.000000] ACPI: RSDP 000F66F0, 0014 (r0 HP-MCD)
[ 0.000000] ACPI: RSDT 040E5A51, 0028 (r1 HP-MCD CI RSDT 7130000 PTL 1000000)
[ 0.000000] ACPI: FACP 040EFB8C, 0074 (r1 HP-MCD CI FACP 7130000 HP 1000000)
[ 0.000000] ACPI: DSDT 040E5A79, A113 (r1 HP-MCD CI DSDT 7130000 MSFT 100000C)
[ 0.000000] ACPI: FACS 040FFBC0, 0040
[ 0.000000] ACPI: BIOS age (1999) fails cutoff (2000), acpi=force is required to enable ACPI
[ 0.000000] ACPI: Disabling ACPI support
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 256MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 10000000
[ 0.000000] low ram: 00000000 - 10000000
[ 0.000000] bootmap 00011000 - 00013000
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 0010000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 000087c52c] TEXT DATA BSS ==> [0000100000 - 000087c52c]
[ 0.000000] #4 [00039a2000 - 00040d4f80] RAMDISK ==> [00039a2000 - 00040d4f80]
[ 0.000000] #5 [000087d000 - 0000881000] INIT_PG_TABLE ==> [000087d000 - 0000881000]
[ 0.000000] #6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
[ 0.000000] #8 [0000011000 - 0000013000] BOOTMAP ==> [0000011000 - 0000013000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x00010000
[ 0.000000] HighMem 0x00010000 -> 0x00010000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000040e5
[ 0.000000] 0: 0x00004100 -> 0x00010000
[ 0.000000] On node 0 totalpages: 65396
[ 0.000000] free_area_init_node: node 0, pgdat c06d0f80, node_mem_map c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 480 pages used for memmap
[ 0.000000] Normal zone: 60933 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f1000
[ 0.000000] PM: Registered nosave memory: 00000000000f1000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000040e5000 - 00000000040e6000
[ 0.000000] PM: Registered nosave memory: 00000000040e6000 - 00000000040ef000
[ 0.000000] PM: Registered nosave memory: 00000000040ef000 - 00000000040f0000
[ 0.000000] PM: Registered nosave memory: 00000000040f0000 - 00000000040ff000
[ 0.000000] PM: Registered nosave memory: 00000000040ff000 - 0000000004100000
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:efff0800)
[ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 1, nr_node_ids 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64884
[ 0.000000] Kernel command line: root=UUID=5f47842a-ba9d-4d0e-b9c7-bdea05453506 ro quiet splash
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] TSC: Using PIT calibration value
[ 0.000000] Detected 363.940 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.004000] allocated 1310400 bytes of page_cgroup
[ 0.004000] please try cgroup_disable=memory option if you don't want
[ 0.004000] Scanning for low memory corruption every 60 seconds
[ 0.004000] Memory: 242592k/262144k available (4126k kernel code, 18668k reserved, 2208k data, 532k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB)
[ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.004000] vmalloc : 0xd0800000 - 0xff3fe000 ( 747 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.004000] .init : 0xc0737000 - 0xc07bc000 ( 532 kB)
[ 0.004000] .data : 0xc0507a6f - 0xc072fe60 (2208 kB)
[ 0.004000] .text : 0xc0100000 - 0xc0507a6f (4126 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.004038] Calibrating delay loop (skipped), value calculated using timer frequency.. 727.88 BogoMIPS (lpj=1455760)
[ 0.004140] Security Framework initialized
[ 0.004181] SELinux: Disabled at boot.
[ 0.004293] AppArmor: AppArmor initialized
[ 0.004341] Mount-cache hash table entries: 512
[ 0.005015] Initializing cgroup subsys ns
[ 0.005037] Initializing cgroup subsys cpuacct
[ 0.005054] Initializing cgroup subsys memory
[ 0.005077] Initializing cgroup subsys freezer
[ 0.005149] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 0.005168] CPU: L2 cache: 256K
[ 0.005248] Checking 'hlt' instruction... OK.
[ 0.020317] SMP alternatives: switching to UP code
[ 0.715402] Freeing SMP alternatives: 18k freed
[ 0.716380] weird, boot CPU (#0) not listedby the BIOS.
[ 0.716395] SMP motherboard not detected.
[ 0.716412] Local APIC not detected. Using dummy APIC emulation.
[ 0.716424] SMP disabled
[ 0.718506] Brought up 1 CPUs
[ 0.718531] Total of 1 processors activated (727.88 BogoMIPS).
[ 0.718624] CPU0 attaching NULL sched-domain.
[ 0.720408] net_namespace: 776 bytes
[ 0.720471] Booting paravirtualized kernel on bare hardware
[ 0.721994] Time: 16:43:45 Date: 09/08/09
[ 0.722026] regulator: core version 0.5
[ 0.722231] NET: Registered protocol family 16
[ 0.723033] EISA bus registered
[ 0.724411] PCI: PCI BIOS revision 2.10 entry at 0xfd9db, last bus=1
[ 0.724430] PCI: Using configuration type 1 for base access
[ 0.732148] ACPI: Interpreter disabled.
[ 0.733172] SCSI subsystem initialized
[ 0.733478] libata version 3.00 loaded.
[ 0.733819] usbcore: registered new interface driver usbfs
[ 0.733924] usbcore: registered new interface driver hub
[ 0.734134] usbcore: registered new device driver usb
[ 0.734935] PCI: Probing PCI hardware
[ 0.734953] PCI: Probing PCI hardware (bus 00)
[ 0.735153] pci 0000:00:00.0: reg 10 32bit mmio: [0x000000-0x3ffffff]
[ 0.735353] pci 0000:00:04.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.735385] pci 0000:00:04.0: supports D1 D2
[ 0.735401] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot
[ 0.735420] pci 0000:00:04.0: PME# disabled
[ 0.735495] pci 0000:00:04.1: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.735526] pci 0000:00:04.1: supports D1 D2
[ 0.735539] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot
[ 0.735557] pci 0000:00:04.1: PME# disabled
[ 0.735772] pci 0000:00:07.1: reg 20 io port: [0xfcf0-0xfcff]
[ 0.735893] pci 0000:00:07.2: reg 20 io port: [0xfcc0-0xfcdf]
[ 0.736101] pci 0000:00:07.3: quirk: region 8000-803f claimed by PIIX4 ACPI
[ 0.736123] pci 0000:00:07.3: quirk: region 2180-218f claimed by PIIX4 SMB
[ 0.736144] pci 0000:00:07.3: PIIX4 devres B PIO at 0530-0537
[ 0.736160] pci 0000:00:07.3: PIIX4 devres C PIO at 0388-038f
[ 0.736177] pci 0000:00:07.3: PIIX4 devres E PIO at 0120-0121
[ 0.736334] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[ 0.736361] pci 0000:01:00.0: reg 14 32bit mmio: [0xfe800000-0xfebfffff]
[ 0.736386] pci 0000:01:00.0: reg 18 32bit mmio: [0xfec00000-0xfecfffff]
[ 0.736446] pci 0000:01:00.0: supports D1 D2
[ 0.736519] pci 0000:01:00.1: reg 10 32bit mmio: [0xfe000000-0xfe3fffff]
[ 0.736544] pci 0000:01:00.1: reg 14 32bit mmio: [0xfe700000-0xfe7fffff]
[ 0.736702] pci 0000:00:01.0: bridge 32bit mmio: [0xfe700000-0xfecfffff]
[ 0.736724] pci 0000:00:01.0: bridge 32bit mmio pref: [0xfd000000-0xfe3fffff]
[ 0.738499] pci 0000:00:07.0: PIIX/ICH IRQ router [8086:7110]
[ 0.738565] PCI: setting IRQ 10 as level-triggered
[ 0.738583] pci 0000:00:04.0: found PCI INT A -> IRQ 10
[ 0.738653] pci 0000:00:04.1: found PCI INT B -> IRQ 10
[ 0.738711] pci 0000:00:04.1: sharing IRQ 10 with 0000:01:00.1
[ 0.739108] Bluetooth: Core ver 2.13
[ 0.739108] NET: Registered protocol family 31
[ 0.739108] Bluetooth: HCI device and connection manager initialized
[ 0.739108] Bluetooth: HCI socket layer initialized
[ 0.739108] NET: Registered protocol family 8
[ 0.739108] NET: Registered protocol family 20
[ 0.739108] NetLabel: Initializing
[ 0.739108] NetLabel: domain hash size = 128
[ 0.739108] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.739108] NetLabel: unlabeled traffic allowed by default
[ 0.740384] AppArmor: AppArmor Filesystem Enabled
[ 0.740400] pnp: PnP ACPI: disabled
[ 0.740421] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.740502] PnPBIOS: Found PnP BIOS installation structure at 0xc00f6760
[ 0.740520] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xac12, dseg 0x400
[ 0.742843] pnp 00:05: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x3ffffff), disabling
[ 0.742868] pnp 00:05: mem resource (0xd8000-0xfffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x3ffffff), disabling
[ 0.742890] pnp 00:05: mem resource (0x100000-0xfffffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x3ffffff), disabling
[ 0.785279] PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
[ 0.785347] system 00:04: ioport range 0x401-0x407 has been reserved
[ 0.785371] system 00:04: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.785431] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[ 0.785449] system 00:0a: ioport range 0x8000-0x803f has been reserved
[ 0.785467] system 00:0a: ioport range 0x2180-0x218f has been reserved
[ 0.786702] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.786719] pci 0000:00:01.0: IO window: disabled
[ 0.786739] pci 0000:00:01.0: MEM window: 0xfe700000-0xfecfffff
[ 0.786759] pci 0000:00:01.0: PREFETCH window: 0x000000fd000000-0x000000fe3fffff
[ 0.786785] pci 0000:00:04.0: CardBus bridge, secondary bus 0000:02
[ 0.786801] pci 0000:00:04.0: IO window: 0x001000-0x0010ff
[ 0.786819] pci 0000:00:04.0: IO window: 0x001400-0x0014ff
[ 0.786838] pci 0000:00:04.0: PREFETCH window: 0x20000000-0x23ffffff
[ 0.786857] pci 0000:00:04.0: MEM window: 0x24000000-0x27ffffff
[ 0.786876] pci 0000:00:04.1: CardBus bridge, secondary bus 0000:06
[ 0.786890] pci 0000:00:04.1: IO window: 0x001800-0x0018ff
[ 0.786908] pci 0000:00:04.1: IO window: 0x001c00-0x001cff
[ 0.786926] pci 0000:00:04.1: PREFETCH window: 0x28000000-0x2bffffff
[ 0.786945] pci 0000:00:04.1: MEM window: 0x2c000000-0x2fffffff
[ 0.787002] pci 0000:00:04.0: found PCI INT A -> IRQ 10
[ 0.787085] pci 0000:00:04.1: found PCI INT B -> IRQ 10
[ 0.787144] pci 0000:00:04.1: sharing IRQ 10 with 0000:01:00.1
[ 0.787170] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.787184] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.787198] bus: 01 index 0 mmio: [0x0-0x0]
[ 0.787212] bus: 01 index 1 mmio: [0xfe700000-0xfecfffff]
[ 0.787226] bus: 01 index 2 mmio: [0xfd000000-0xfe3fffff]
[ 0.787239] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.787253] bus: 02 index 0 io port: [0x1000-0x10ff]
[ 0.787266] bus: 02 index 1 io port: [0x1400-0x14ff]
[ 0.787280] bus: 02 index 2 mmio: [0x20000000-0x23ffffff]
[ 0.787295] bus: 02 index 3 mmio: [0x24000000-0x27ffffff]
[ 0.787309] bus: 06 index 0 io port: [0x1800-0x18ff]
[ 0.787323] bus: 06 index 1 io port: [0x1c00-0x1cff]
[ 0.787337] bus: 06 index 2 mmio: [0x28000000-0x2bffffff]
[ 0.787351] bus: 06 index 3 mmio: [0x2c000000-0x2fffffff]
[ 0.787406] NET: Registered protocol family 2
[ 0.788268] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.789827] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.790158] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.790477] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.790493] TCP reno registered
[ 0.791062] NET: Registered protocol family 1
[ 0.791807] checking if image is initramfs... it is
[ 4.364409] Freeing initrd memory: 7371k freed
[ 4.364766] cpufreq: No nForce2 chipset.
[ 4.365437] audit: initializing netlink socket (disabled)
[ 4.365521] type=2000 audit(1252428228.364:1): initialized
[ 4.411558] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 4.420884] VFS: Disk quotas dquot_6.5.1
[ 4.421324] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 4.425830] fuse init (API version 7.10)
[ 4.426441] msgmni has been set to 488
[ 4.427735] alg: No test for stdrng (krng)
[ 4.427834] io scheduler noop registered
[ 4.427849] io scheduler anticipatory registered
[ 4.427862] io scheduler deadline registered
[ 4.428024] io scheduler cfq registered (default)
[ 4.428097] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 4.428189] pci 0000:01:00.0: Boot video device
[ 4.428804] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 4.428866] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 4.430004] isapnp: Scanning for PnP cards...
[ 4.783303] isapnp: No Plug & Play device found
[ 4.790958] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 4.791201] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.793082] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 4.798200] brd: module loaded
[ 4.800392] loop: module loaded
[ 4.800980] Fixed MDIO Bus: probed
[ 4.801020] PPP generic driver version 2.4.2
[ 4.801396] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 4.801596] Driver 'sd' needs updating - please use bus_type methods
[ 4.801659] Driver 'sr' needs updating - please use bus_type methods
[ 4.802084] ata_piix 0000:00:07.1: version 2.12
[ 4.802878] scsi0 : ata_piix
[ 4.803568] scsi1 : ata_piix
[ 4.803791] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xfcf0 irq 14
[ 4.803810] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xfcf8 irq 15
[ 5.302587] ata1.00: ATA-4: IBM-DCXA-210000, CX6OA87F, max UDMA/33
[ 5.302606] ata1.00: 19640880 sectors, multi 16: LBA
[ 5.345421] ata1.00: configured for UDMA/33
[ 5.501093] ata2.00: ATAPI: TOSHIBA DVD-ROM SD-C2202, 1R13, max UDMA/33
[ 5.501985] ata2.00: configured for UDMA/33
[ 5.502881] scsi 0:0:0:0: Direct-Access ATA IBM-DCXA-210000 CX6O PQ: 0 ANSI: 5
[ 5.503569] sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors: (10.0 GB/9.36 GiB)
[ 5.503702] sd 0:0:0:0: [sda] Write Protect is off
[ 5.503720] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.503939] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.504376] sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors: (10.0 GB/9.36 GiB)
[ 5.504500] sd 0:0:0:0: [sda] Write Protect is off
[ 5.504561] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.504781] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.504810] sda: sda1 sda2 < sda5 >
[ 5.610412] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.610735] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.611753] scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-C2202 1R13 PQ: 0 ANSI: 5
[ 5.614851] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 5.614871] Uniform CD-ROM driver Revision: 3.20
[ 5.615494] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 5.615818] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.619563] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.619681] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.619795] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.620016] uhci_hcd 0000:00:07.2: enabling device (0000 -> 0001)
[ 5.620051] uhci_hcd 0000:00:07.2: found PCI INT D -> IRQ 10
[ 5.620147] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 5.620595] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 5.620676] uhci_hcd 0000:00:07.2: irq 10, io base 0x0000fcc0
[ 5.621298] usb usb1: configuration #1 chosen from 1 choice
[ 5.621482] hub 1-0:1.0: USB hub found
[ 5.621545] hub 1-0:1.0: 2 ports detected
[ 5.622342] usbcore: registered new interface driver libusual
[ 5.622537] usbcore: registered new interface driver usbserial
[ 5.622606] USB Serial support registered for generic
[ 5.622688] usbcore: registered new interface driver usbserial_generic
[ 5.622704] usbserial: USB Serial Driver core
[ 5.623018] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 5.636617] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.636653] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 5.637361] mice: PS/2 mouse device common for all mice
[ 5.637922] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 5.637980] rtc0: alarms up to one day, 114 bytes nvram
[ 5.638505] device-mapper: uevent: version 1.0.3
[ 5.639247] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 5.639633] device-mapper: multipath: version 1.0.5 loaded
[ 5.639652] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 5.640287] EISA: Probing bus 0 at eisa.0
[ 5.640319] Cannot allocate resource for EISA slot 1
[ 5.640376] Cannot allocate resource for EISA slot 8
[ 5.640389] EISA: Detected 0 cards.
[ 5.640646] cpuidle: using governor ladder
[ 5.640662] cpuidle: using governor menu
[ 5.644272] TCP cubic registered
[ 5.645148] NET: Registered protocol family 10
[ 5.647917] lo: Disabled Privacy Extensions
[ 5.650159] NET: Registered protocol family 17
[ 5.650297] Bluetooth: L2CAP ver 2.11
[ 5.650311] Bluetooth: L2CAP socket layer initialized
[ 5.650330] Bluetooth: SCO (Voice Link) ver 0.6
[ 5.650342] Bluetooth: SCO socket layer initialized
[ 5.650617] Bluetooth: RFCOMM socket layer initialized
[ 5.650666] Bluetooth: RFCOMM TTY layer initialized
[ 5.650679] Bluetooth: RFCOMM ver 1.10
[ 5.650899] IO APIC resources could be not be allocated.
[ 5.650974] Using IPI No-Shortcut mode
[ 5.651469] registered taskstats version 1
[ 5.651977] Magic number: 9:1:742
[ 5.652192] rtc_cmos 00:03: setting system clock to 2009-09-08 16:43:50 UTC (1252428230)
[ 5.652213] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.652226] EDD information not available.
[ 5.656052] Freeing unused kernel memory: 532k freed
[ 5.656948] Write protecting the kernel text: 4128k
[ 5.657196] Write protecting the kernel read-only data: 1532k
[ 5.677018] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 5.932727] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 6.100347] usb 1-1: configuration #1 chosen from 1 choice
[ 6.152004] Initializing USB Mass Storage driver...
[ 6.152739] scsi2 : SCSI emulation for USB Mass Storage devices
[ 6.160255] usbcore: registered new interface driver usb-storage
[ 6.160284] USB Mass Storage support registered.
[ 6.160935] usb-storage: device found at 2
[ 6.160950] usb-storage: waiting for device to settle before scanning
[ 9.605962] PM: Starting manual resume from disk
[ 9.605989] PM: Resume from partition 8:5
[ 9.606001] PM: Checking hibernation image.
[ 9.606571] PM: Resume from disk failed.
[ 9.669717] kjournald starting. Commit interval 5 seconds
[ 9.669789] EXT3-fs: mounted filesystem with ordered data mode.
[ 11.164698] usb-storage: device scan complete
[ 11.170258] scsi 2:0:0:0: Direct-Access IBM Memory Key 3.52 PQ: 0 ANSI: 0 CCS
[ 11.188851] sd 2:0:0:0: [sdb] 499712 512-byte hardware sectors: (255 MB/244 MiB)
[ 11.192492] sd 2:0:0:0: [sdb] Write Protect is off
[ 11.192518] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 11.192560] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 11.206225] sd 2:0:0:0: [sdb] 499712 512-byte hardware sectors: (255 MB/244 MiB)
[ 11.209470] sd 2:0:0:0: [sdb] Write Protect is off
[ 11.209489] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 11.209521] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 11.209702] sdb: sdb1
[ 11.224963] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 11.226806] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 24.256074] udev: starting version 141
[ 25.370933] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 25.608278] Linux agpgart interface v0.103
[ 25.706732] yenta_cardbus 0000:00:04.0: CardBus bridge found [103c:0007]
[ 25.706861] yenta_cardbus 0000:00:04.0: Enabling burst memory read transactions
[ 25.706887] yenta_cardbus 0000:00:04.0: Using CSCINT to route CSC interrupts to PCI
[ 25.706903] yenta_cardbus 0000:00:04.0: Routing CardBus interrupts to PCI
[ 25.706925] yenta_cardbus 0000:00:04.0: TI: mfunc 0x01021c02, devctl 0x66
[ 25.958007] yenta_cardbus 0000:00:04.0: ISA IRQ mask 0x0898, PCI irq 10
[ 25.958033] yenta_cardbus 0000:00:04.0: Socket status: 30000010
[ 25.977958] piix4_smbus 0000:00:07.3: SMBus Host Controller at 0x2180, revision 0
[ 25.978791] yenta_cardbus 0000:00:04.1: CardBus bridge found [103c:0007]
[ 25.979051] yenta_cardbus 0000:00:04.1: Using CSCINT to route CSC interrupts to PCI
[ 25.979070] yenta_cardbus 0000:00:04.1: Routing CardBus interrupts to PCI
[ 25.979092] yenta_cardbus 0000:00:04.1: TI: mfunc 0x01021c02, devctl 0x66
[ 26.003468] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 26.227359] yenta_cardbus 0000:00:04.1: ISA IRQ mask 0x0898, PCI irq 10
[ 26.227392] yenta_cardbus 0000:00:04.1: Socket status: 30000006
[ 26.326378] agpgart-intel 0000:00:00.0: Intel 440BX Chipset
[ 26.345845] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0x34000000
[ 26.631041] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 26.769049] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 27.350671] psmouse serio1: ID: 10 00 64<6>IBM TrackPoint firmware: 0x0b, buttons: 3/3
[ 27.828179] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input3
[ 28.725425] nm256: The device is blacklisted. Loading stopped
[ 29.152094] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: excluding 0x120-0x127 0x220-0x22f 0x378-0x37f 0x388-0x38f
[ 29.153443] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
[ 29.154137] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
[ 29.154784] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
[ 29.156272] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[ 29.601295] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x120-0x127 0x220-0x22f 0x378-0x37f 0x388-0x38f
[ 29.602647] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 29.603416] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 29.604060] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 29.605505] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 29.606212] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 29.613815] pcmcia 0.0: pcmcia: registering new device pcmcia0.0
[ 29.781792] pcmcia 0.0: firmware: requesting 3CCFEM556.cis
[ 29.850955] pcmcia 0.0: firmware: requesting 3CCFEM556.cis
[ 30.556010] lp: driver loaded but no devices found
[ 31.078810] Adding 465844k swap on /dev/sda5. Priority:-1 extents:1 across:465844k
[ 32.146875] EXT3 FS on sda1, internal journal
[ 35.215925] type=1505 audit(1252428260.059:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1703
[ 35.590939] type=1505 audit(1252428260.435:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1707
[ 35.592213] type=1505 audit(1252428260.439:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1707
[ 35.592689] type=1505 audit(1252428260.439:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1707
[ 35.593066] type=1505 audit(1252428260.439:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1707
[ 36.666939] type=1505 audit(1252428261.511:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1712
[ 36.668674] type=1505 audit(1252428261.515:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1712
[ 36.886581] type=1505 audit(1252428261.731:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1716
[ 46.861668] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 46.861690] Bluetooth: BNEP filters: protocol multicast
[ 47.059052] Bridge firewalling registered
[ 50.666687] ppdev: user-space parallel port driver
[ 1916.465309] usb 1-1: USB disconnect, address 2
[ 1916.471908] Buffer I/O error on device sdb1, logical block 489
[ 1916.471934] lost page write due to I/O error on sdb1
[ 1916.761480] scsi 2:0:0:0: rejecting I/O to dead device
[ 1943.920618] pcmcia_socket pcmcia_socket0: pccard: card ejected from slot 0
[ 2837.611755] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 2837.612003] pcmcia 0.0: pcmcia: registering new device pcmcia0.0
[ 2837.612362] pcmcia 0.0: firmware: requesting 3CCFEM556.cis
[ 2837.687853] pcmcia 0.0: firmware: requesting 3CCFEM556.cis
jimtino@jimtino-laptop:~$
 
Old 09-11-2009, 09:51 PM   #4
Drakeo
Senior Member
 
Registered: Jan 2008
Location: Urbana IL
Distribution: Slackware, Slacko,
Posts: 3,154
Blog Entries: 3

Rep: Reputation: 340Reputation: 340Reputation: 340Reputation: 340
please insert the card before starting linux. then type as root lspci and post it. lsmod and post it.
your dmesg should change and load the card earlier. From your dmseg you pushed the card in after linux had started. as root ifconfig eth0 up Then type as root ifconfig and post it.
 
Old 09-12-2009, 04:31 PM   #5
jimtino
LQ Newbie
 
Registered: Sep 2009
Posts: 3

Original Poster
Rep: Reputation: 0
lsmod and lspci output

Thanks so much for hanging with me on this one Drakeo. Here is the output from lspci, lsmod, ifconfig, and another dmesg dump.

Jim

*** LSPCI ***
root@jimtino-laptop:/home/jimtino# lspci
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:04.0 CardBus bridge: Texas Instruments PCI1220 (rev 02)
00:04.1 CardBus bridge: Texas Instruments PCI1220 (rev 02)
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
01:00.0 VGA compatible controller: Neomagic Corporation NM2200 [MagicGraph 256AV] (rev 12)
01:00.1 Multimedia audio controller: Neomagic Corporation NM2200 [MagicMedia 256AV Audio] (rev 12)

*** LSMOD ***

root@jimtino-laptop:/home/jimtino# lsmod
Module Size Used by
nls_iso8859_1 12032 1
nls_cp437 13696 1
vfat 18816 1
fat 58272 1 vfat
binfmt_misc 16776 1
ppdev 15620 0
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
lp 17156 0
parport 42220 2 ppdev,lp
3c574_cs 19720 0
pcmcia 44748 1 3c574_cs
snd_nm256 74144 0
snd_ac97_codec 112292 1 snd_nm256
ac97_bus 9856 1 snd_ac97_codec
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 82948 3 snd_nm256,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 16904 1 snd_pcm


**** ifconfig eth0 up *****

root@jimtino-laptop:/home/jimtino# ifconfig eth0 up
eth0: ERROR while getting interface flags: No such device
root@jimtino-laptop:/home/jimtino#

*** DMESG ***

ting system clock to 2009-09-12 15:28:30 UTC (1252769310)
[ 5.968984] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.968997] EDD information not available.
[ 5.972896] Freeing unused kernel memory: 532k freed
[ 5.973675] Write protecting the kernel text: 4128k
[ 5.973919] Write protecting the kernel read-only data: 1532k
[ 5.993461] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 6.248956] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 6.415402] usb 1-1: configuration #1 chosen from 1 choice
[ 6.467028] Initializing USB Mass Storage driver...
[ 6.467694] scsi2 : SCSI emulation for USB Mass Storage devices
[ 6.475160] usbcore: registered new interface driver usb-storage
[ 6.475190] USB Mass Storage support registered.
[ 6.475762] usb-storage: device found at 2
[ 6.475776] usb-storage: waiting for device to settle before scanning
[ 9.846366] PM: Starting manual resume from disk
[ 9.846391] PM: Resume from partition 8:5
[ 9.846402] PM: Checking hibernation image.
[ 9.847056] PM: Resume from disk failed.
[ 9.910102] kjournald starting. Commit interval 5 seconds
[ 9.910176] EXT3-fs: mounted filesystem with ordered data mode.
[ 11.477138] usb-storage: device scan complete
[ 11.494231] scsi 2:0:0:0: Direct-Access IBM Memory Key 3.52 PQ: 0 ANSI: 0 CCS
[ 11.518598] sd 2:0:0:0: [sdb] 499712 512-byte hardware sectors: (255 MB/244 MiB)
[ 11.521457] sd 2:0:0:0: [sdb] Write Protect is off
[ 11.521479] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 11.521504] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 11.543816] sd 2:0:0:0: [sdb] 499712 512-byte hardware sectors: (255 MB/244 MiB)
[ 11.546487] sd 2:0:0:0: [sdb] Write Protect is off
[ 11.546513] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 11.546535] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 11.546642] sdb: sdb1
[ 11.561996] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 11.563374] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 24.355810] udev: starting version 141
[ 24.929088] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 25.114200] Linux agpgart interface v0.103
[ 25.551912] piix4_smbus 0000:00:07.3: SMBus Host Controller at 0x2180, revision 0
[ 25.648929] yenta_cardbus 0000:00:04.0: CardBus bridge found [103c:0007]
[ 25.648980] yenta_cardbus 0000:00:04.0: Enabling burst memory read transactions
[ 25.649001] yenta_cardbus 0000:00:04.0: Using CSCINT to route CSC interrupts to PCI
[ 25.649017] yenta_cardbus 0000:00:04.0: Routing CardBus interrupts to PCI
[ 25.649038] yenta_cardbus 0000:00:04.0: TI: mfunc 0x01021c02, devctl 0x66
[ 25.883165] yenta_cardbus 0000:00:04.0: ISA IRQ mask 0x0898, PCI irq 10
[ 25.883194] yenta_cardbus 0000:00:04.0: Socket status: 30000010
[ 25.918964] agpgart-intel 0000:00:00.0: Intel 440BX Chipset
[ 25.929245] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0x34000000
[ 25.929482] yenta_cardbus 0000:00:04.1: CardBus bridge found [103c:0007]
[ 25.929526] yenta_cardbus 0000:00:04.1: Using CSCINT to route CSC interrupts to PCI
[ 25.929542] yenta_cardbus 0000:00:04.1: Routing CardBus interrupts to PCI
[ 25.929563] yenta_cardbus 0000:00:04.1: TI: mfunc 0x01021c02, devctl 0x66
[ 26.046689] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 26.187522] yenta_cardbus 0000:00:04.1: ISA IRQ mask 0x0898, PCI irq 10
[ 26.187549] yenta_cardbus 0000:00:04.1: Socket status: 30000006
[ 26.584317] pcmcia_socket pcmcia_socket0: pccard: PCMCIA card inserted into slot 0
[ 26.636817] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 26.856192] psmouse serio1: ID: 10 00 64<6>IBM TrackPoint firmware: 0x0b, buttons: 3/3
[ 27.354423] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input3
[ 28.627794] nm256: The device is blacklisted. Loading stopped
[ 29.252726] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: excluding 0x120-0x127 0x220-0x22f 0x378-0x37f 0x388-0x38f
[ 29.254085] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
[ 29.254782] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
[ 29.255430] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
[ 29.257201] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[ 29.706374] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x120-0x127 0x220-0x22f 0x378-0x37f 0x388-0x38f
[ 29.707740] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 29.708520] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 29.709171] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 29.710639] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 29.711352] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 29.718986] pcmcia 0.0: pcmcia: registering new device pcmcia0.0
[ 29.896276] pcmcia 0.0: firmware: requesting 3CCFEM556.cis
[ 29.965813] pcmcia 0.0: firmware: requesting 3CCFEM556.cis
[ 30.670823] lp: driver loaded but no devices found
[ 31.198490] Adding 465844k swap on /dev/sda5. Priority:-1 extents:1 across:465844k
[ 32.224941] EXT3 FS on sda1, internal journal
[ 35.402366] type=1505 audit(1252769339.932:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1705
[ 35.777107] type=1505 audit(1252769340.304:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1709
[ 35.778651] type=1505 audit(1252769340.308:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1709
[ 35.779117] type=1505 audit(1252769340.308:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1709
[ 35.779516] type=1505 audit(1252769340.308:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1709
[ 36.851856] type=1505 audit(1252769341.380:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1714
[ 36.853632] type=1505 audit(1252769341.384:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1714
[ 37.071737] type=1505 audit(1252769341.600:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1718
[ 47.103147] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 47.103167] Bluetooth: BNEP filters: protocol multicast
[ 47.293760] Bridge firewalling registered
[ 50.410050] ppdev: user-space parallel port driver
[ 1464.359313] usb 1-1: USB disconnect, address 2
[ 1464.646214] scsi 2:0:0:0: rejecting I/O to dead device
[ 1701.490101] usb 1-1: new full speed USB device using uhci_hcd and address 3
[ 1701.715542] usb 1-1: configuration #1 chosen from 1 choice
[ 1701.759456] scsi3 : SCSI emulation for USB Mass Storage devices
[ 1701.760802] usb-storage: device found at 3
[ 1701.760817] usb-storage: waiting for device to settle before scanning
[ 1706.762472] usb-storage: device scan complete
[ 1706.775130] scsi 3:0:0:0: Direct-Access IBM Memory Key 3.52 PQ: 0 ANSI: 0 CCS
[ 1706.817282] sd 3:0:0:0: [sdb] 499712 512-byte hardware sectors: (255 MB/244 MiB)
[ 1706.827949] sd 3:0:0:0: [sdb] Write Protect is off
[ 1706.828038] sd 3:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 1706.828077] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1706.849490] sd 3:0:0:0: [sdb] 499712 512-byte hardware sectors: (255 MB/244 MiB)
[ 1706.857580] sd 3:0:0:0: [sdb] Write Protect is off
[ 1706.857604] sd 3:0:0:0: [sdb] Mode Sense: 45 00 00 08
[ 1706.857736] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 1706.858024] sdb: sdb1
[ 1706.932062] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 1706.933780] sd 3:0:0:0: Attached scsi generic sg2 type 0
root@jimtino-laptop:/home/jimtino#
 
Old 09-13-2009, 10:06 PM   #6
Drakeo
Senior Member
 
Registered: Jan 2008
Location: Urbana IL
Distribution: Slackware, Slacko,
Posts: 3,154
Blog Entries: 3

Rep: Reputation: 340Reputation: 340Reputation: 340Reputation: 340
please let me know if this is a ether net combo card. if so please give me the chip number on the card if it is a combo card please manually insmod the modules.
Quote:
# modprobe pcmcia
# modprobe 3c574_cs
# modprobe serial_cs
I want you to go into bios and find the pcmcia card socket and change the settings to what ever . there most likely is two or three settings. if this is a combo card 3com ethernet card and a modem let me know that.
I need to know the kernel and distro. open a terminal and type uname -a if you do not post that I will have to give up.
If this is a combo card written for windows we need to let linux load it the right way.
Quote:
we need to load the firmware for it. It most likley is there or needs to be installed but I have no idea what kernel or what distro.

Last edited by Drakeo; 09-13-2009 at 10:08 PM.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
PCMCIA ethernet card czaanja Slackware 2 11-22-2004 03:18 PM
pcmcia ethernet card rabby Slackware 9 03-09-2004 08:57 AM
Insert scsi pcmcia card kills existing ethernet card lgetsche Linux - Hardware 0 11-12-2002 05:16 PM
Can't network pcmcia card with Intel eepro100 ethernet card. RKris Linux - Networking 1 06-18-2002 01:43 PM
pcmcia ethernet card athenerx Linux - Software 1 12-17-2001 12:14 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Newbie

All times are GMT -5. The time now is 10:53 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Facebook: linuxquestions Google+: linuxquestions
Open Source Consulting | Domain Registration