hi i'm new to this i installed vmware & bt4 beta on my laptop host is win xp now i can surf the net on bt4 but when i get in to commands like airmon-ng all that shows up is

Interface Chipset Driver

an when i type in dmesg:

sd 2:0:0:0: [sda] Attached SCSI disk
Fusion MPT FC Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:02:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:02:03.0: EHCI Host Controller
ehci_hcd 0000:02:03.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:02:03.0: cache line size of 32 is not supported
ehci_hcd 0000:02:03.0: irq 17, io mem 0xd8900000
ehci_hcd 0000:02:03.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:02:00.0: UHCI Host Controller
uhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:02:00.0: irq 18, io base 0x000020c0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUS] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 233 MB/s
raid6: int32x2 256 MB/s

an if i type in sudo airmon-ng start Ra0 11
root@bt:~# sudo airmon-ng start ra0 11


Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!
-e
PID Name
4170 dhclient3
4408 knetworkmanager


Interface Chipset Driver


root@bt:~#
is my wireless usb not being reconized?
i did the set-up for wireless but how do i know it's turned on?

Nothing in your post has anything to do with the wireless hardware, so it is impossible to say with the given information.

Which modules does your hardware use? Are you able to do a simple scan of nearby APs with a command like "iwlist wlan0 scan", replacing "wlan0" with whatever your WiFi interface is.

this is what i get with iwlist scan


root@bt:~# iwlist Ralink scan
Ralink Interface doesn't support scanning.

this is my wireless usb adapter

http://www.intellinet-network.com/en...0n-usb-adapter