LinuxQuestions.org
Share your knowledge at the LQ Wiki.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Networking
User Name
Password
Linux - Networking This forum is for any issue related to networks or networking.
Routing, network cards, OSI, etc. Anything is fair game.

Notices


Reply
  Search this Thread
Old 12-22-2004, 10:50 PM   #1
Padmakiran
LQ Newbie
 
Registered: Dec 2004
Location: India
Distribution: Slackware
Posts: 9

Rep: Reputation: 0
Question Slackware 10 network configuration. Problem with 8139 network card drivers !


Hi ppl,

I tried configuring network on my slackware 10 linux. I used netconfig to update /etc/rc.d/rc.inet1.conf

with a static ip ( 10.185.3.101 ), Gateway(10.185.3.1), and DNS(10.185.50.100). The RTL8139 driver seems

to be inserted and the eth0 interface is up. Now i run all the network services using this command,
/etc/rc.r/rc.inet1 restart,

i fail to ping other systems on my network, after all this.


Following is the boot log of my system along with the snapshot of /proc/interrupts.

--------------------------------------------------------------------------------------

Linux version 2.6.6 (root@White) (gcc version 3.3.4) #1 SMP Mon Dec 20 19:14:22 IST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f7f0000 (usable)
BIOS-e820: 000000001f7f0000 - 000000001f7f8000 (ACPI data)
BIOS-e820: 000000001f7f8000 - 000000001f800000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
503MB LOWMEM available.
found SMP MP-table at 000fbac0
On node 0 totalpages: 129008
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 124912 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI ) @ 0x000f9fb0
ACPI: RSDT (v001 AMIINT INTEL845 0x00000010 MSFT 0x00000097) @ 0x1f7f0000
ACPI: FADT (v001 AMIINT INTEL845 0x00000011 MSFT 0x00000097) @ 0x1f7f0030
ACPI: MADT (v001 AMIINT INTEL845 0x00000009 MSFT 0x00000097) @ 0x1f7f00c0
ACPI: DSDT (v001 INTEL P4I45GL 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Linux-2.6.6 ro root=303
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2259.725 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 506764k/516032k available (2671k kernel code, 8508k reserved, 1046k data, 184k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4456.44 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU0: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 09
per-CPU timeslice cutoff: 1462.82 usecs.
task migration cache decay timeout: 2 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Total of 1 processors activated (4456.44 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2259.0120 MHz.
..... host bus clock speed is 132.0889 MHz.
Brought up 1 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb51, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
00:00:1f[A] -> 2-18 -> IRQ 18 level low
00:00:1f[B] -> 2-17 -> IRQ 17 level low
00:00:1d[A] -> 2-16 -> IRQ 16 level low
00:00:1d[B] -> 2-19 -> IRQ 19 level low
00:00:1d[D] -> 2-23 -> IRQ 23 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 0FF 0F 0 0 0 0 0 1 1 39
02 0FF 0F 0 0 0 0 0 1 1 31
03 0FF 0F 0 0 0 0 0 1 1 41
04 0FF 0F 0 0 0 0 0 1 1 49
05 0FF 0F 0 0 0 0 0 1 1 51
06 0FF 0F 0 0 0 0 0 1 1 59
07 0FF 0F 0 0 0 0 0 1 1 61
08 0FF 0F 0 0 0 0 0 1 1 69
09 0FF 0F 0 1 0 0 0 1 1 71
0a 0FF 0F 0 0 0 0 0 1 1 79
0b 0FF 0F 0 0 0 0 0 1 1 81
0c 0FF 0F 0 0 0 0 0 1 1 89
0d 0FF 0F 0 0 0 0 0 1 1 91
0e 0FF 0F 0 0 0 0 0 1 1 99
0f 0FF 0F 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 B9
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 A9
13 001 01 1 1 0 1 0 1 1 C1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 C9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
Machine check exception polling timer started.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
lp: driver loaded but no devices found
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xd0000000
[drm] Initialized i830 1.3.2 20021108 on minor 0
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
lp0: using parport0 (polling).
Using anticipatory io scheduler
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xcc00, 00:0b:6a:67:a4:20, IRQ 17
eth0: Identified 8139 chip type 'RTL-8101'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 2F040L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: hda1 hda2 < hda5 > hda3 hda4
libata version 1.02 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB USB2
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem e008dc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 0000e400
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 0000e800
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB USB (Hub #3)
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 0000ec00
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 1.0.4rc2 (Tue Mar 30 08:19:30 2004 UTC).
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49297 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel 82801DB-ICH4 at 0xdff7ba00, irq 17
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
ip_conntrack version 2.1 (4031 buckets, 32248 max) - 300 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Adding 971924k swap on /dev/hda4. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 00002000. (queue head)
eth0: Tx descriptor 1 is 00002000.
eth0: Tx descriptor 2 is 00002000.
eth0: Tx descriptor 3 is 00002000.
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1

-----------------------------------------------------------------------

/proc/interrupts:
--------------------------
CPU0
0: 190696 IO-APIC-edge timer
1: 751 IO-APIC-edge i8042
9: 0 IO-APIC-level acpi
12: 5644 IO-APIC-edge i8042
14: 5247 IO-APIC-edge ide0
16: 0 IO-APIC-level uhci_hcd
17: 0 IO-APIC-level Intel 82801DB-ICH4, eth0
18: 0 IO-APIC-level uhci_hcd
19: 0 IO-APIC-level uhci_hcd
23: 0 IO-APIC-level ehci_hcd
NMI: 0
LOC: 190603
ERR: 0
MIS: 0

-------------------------------------------------------------------

I seem to be having problem with my 8139too drivers. Every time i try to ping the gateway (10.185.3.1) i

get the message
NETDEV WATCHDOG: eth0: transmit timed out


Any suggestions ??
 
Old 12-23-2004, 01:54 AM   #2
iZvi
Member
 
Registered: Mar 2004
Location: Valhalla
Distribution: Slackware-current, kernel 2.6.31
Posts: 284

Rep: Reputation: 35
Hi,
I have the same NIC and the stock kernel always detects it. These cards are very well supported in almost any OS. See the output of "ifconfig eth0" and "route", ping your own IP and see the results (if the interface transmits any packets)
 
Old 12-23-2004, 02:38 AM   #3
Padmakiran
LQ Newbie
 
Registered: Dec 2004
Location: India
Distribution: Slackware
Posts: 9

Original Poster
Rep: Reputation: 0
Hi iZvi,

When i try to ping my own ip address, It works. But when i try to ping my gateway !! I'm not able to and the dmesg shows this error message :

NETDEV WATCHDOG: eth0: transmit timed out
eth0: Tx queue start entry 4 dirty entry 0.
eth0: Tx descriptor 0 is 00002000. (queue head)
eth0: Tx descriptor 1 is 00002000.
eth0: Tx descriptor 2 is 00002000.
eth0: Tx descriptor 3 is 00002000.
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
 
Old 03-21-2006, 06:42 AM   #4
scolic
LQ Newbie
 
Registered: Mar 2006
Location: Belgrade,Serbia
Distribution: Slackware 14.1 x64
Posts: 5

Rep: Reputation: 0
i hate myself and this stupid card :mad:

I also have a problem making this card work. it's detected by the kernel at login, but when i run netconfig on slackware 10.2 2.4.sth precompiled out of the box kernel, i put static ip like in windows xp, probably there's the catch.
And when i reboot the system locks up when ifconfig tires to do something. So i manualy jerked around rc.inet1.config but no luck.
On Xp it runs perfectly.
I don't know where did i go wrong. I manualy via rc.modules enabled too8139 but lsmod says it's [unused].

I suggest http://www.scyld.com/rtl8139.html
they have some drivers and stuff there you might wanna check it out.

Last edited by scolic; 03-21-2006 at 06:49 AM.
 
Old 03-21-2006, 07:08 AM   #5
Padmakiran
LQ Newbie
 
Registered: Dec 2004
Location: India
Distribution: Slackware
Posts: 9

Original Poster
Rep: Reputation: 0
slackware ethernet card driver problem.

scolic,

I came through that problem by recompiling the ethernet driver for 8139 with some small modifications. I really don't remember the hack though(It was quite some time back). Are you able to check the kernel log using dmesg ? Usually these logs help a lot at narrowing down to the problem(use dmesg command Or cat /var/log/messages).

after having inserted the ethernet drivers into the kernel, did u use this commnd ?

ifconfig eth<that particular interface> up
for example: ifconfig eth0 up

Once u do this the inserted module will be used by the kernel..

Regards,
Padmakiran
 
Old 03-21-2006, 09:32 AM   #6
onebuck
Moderator
 
Registered: Jan 2005
Location: Central Florida 20 minutes from Disney World
Distribution: SlackwareŽ
Posts: 13,922
Blog Entries: 44

Rep: Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158
Hi,

What is the output of the following from console;
Quote:

Please put the information in the quote format to allow ease of use by cut and paste.

#lspci -vv #show me the pci info
#lsmod #modules
#ifconfig -a #network device info
#route -n #network routes
Hurt to read your original post. If placed in quotes then we can scroll through with ease.

BTW, the output is dmesg not boot message.

Learn to use your system logs, this way you can find some points to the problems that may exist.

Last edited by onebuck; 03-21-2006 at 09:33 AM.
 
Old 03-25-2006, 07:12 AM   #7
scolic
LQ Newbie
 
Registered: Mar 2006
Location: Belgrade,Serbia
Distribution: Slackware 14.1 x64
Posts: 5

Rep: Reputation: 0
root@darkstar:/# lspci -vv
Code:
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
        Subsystem: ASUSTeK Computer Inc. A7V-E Mainboard
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] PCI Bridge (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        Memory behind bridge: ee000000-efefffff
        Prefetchable memory behind bridge: eff00000-f7ffffff
        BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
        Subsystem: ASUSTeK Computer Inc. A7V-E Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Region 4: I/O ports at d800 [size=16]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, cache line size 08
        Interrupt: pin D routed to IRQ 9
        Region 4: I/O ports at d400 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, cache line size 08
        Interrupt: pin D routed to IRQ 9
        Region 4: I/O ports at d000 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
        Subsystem: ASUSTeK Computer Inc. A7V-E Mainboard
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin ? routed to IRQ 9
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
        Subsystem: ASUSTeK Computer Inc.: Unknown device 4005
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 7
        Region 0: I/O ports at b800 [size=256]
        Region 1: I/O ports at b400 [size=4]
        Region 2: I/O ports at b000 [size=4]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Communication controller: Rockwell International HCF 56k Data/Fax/Voice/Spkp (w/Handset) Modem (rev 01)
        Subsystem: Rockwell International HCF 56k Data/Fax/Voice/Spkp (w/Handset) Modem
        Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Interrupt: pin A routed to IRQ 0
        Region 0: Memory at ed800000 (32-bit, non-prefetchable) [disabled] [size=64K]
        Region 1: I/O ports at a400 [disabled] [size=8]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable+ DSel=0 DScale=0 PME-

00:0e.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 5
        Region 0: I/O ports at a000 [size=128]
        Region 1: Memory at ed000000 (32-bit, non-prefetchable) [size=128]

01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2) (prog-if 00 [VGA])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
        Expansion ROM at efff0000 [disabled] [size=64K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [44] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
lsmod

Code:
Module                  Size  Used by    Not tainted
snd-pcm-oss            36736   0  (unused)
snd-mixer-oss          12376   0  [snd-pcm-oss]
snd-via82xx            13376   1
gameport                1420   0  [snd-via82xx]
snd-ac97-codec         58556   0  [snd-via82xx]
snd-pcm                54344   0  [snd-pcm-oss snd-via82xx snd-ac97-codec]
snd-timer              13764   0  [snd-pcm]
snd-mpu401-uart         3136   0  [snd-via82xx]
snd-rawmidi            12480   0  [snd-mpu401-uart]
snd-seq-device          3812   0  [snd-rawmidi]
snd                    32772   1  [snd-pcm-oss snd-mixer-oss snd-via82xx snd-ac97-codec snd-pcm snd-timer snd-mpu401-uart snd-rawmidi snd-seq-device]
snd-page-alloc          4712   0  [snd-mixer-oss snd-via82xx snd-pcm snd-timer snd-rawmidi snd-seq-device snd]
soundcore               3396   3  [snd]
ntfs                   51232   2  (autoclean)
ide-scsi                9392   0
8139too                13928   0  (unused)
mii                     2272   0  [8139too]
crc32                   2880   0  [8139too]
agpgart                45508   0  (unused)
ifconfig -a

Code:
eth0      Link encap:Ethernet  HWaddr 00:C0:CA:11:4A:09
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:5 Base address:0xa000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:352 errors:0 dropped:0 overruns:0 frame:0
          TX packets:352 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:31840 (31.0 Kb)  TX bytes:31840 (31.0 Kb)
route -n

Code:
root@darkstar:/# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
 
Old 03-26-2006, 10:15 AM   #8
onebuck
Moderator
 
Registered: Jan 2005
Location: Central Florida 20 minutes from Disney World
Distribution: SlackwareŽ
Posts: 13,922
Blog Entries: 44

Rep: Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158Reputation: 3158
Hi,

Sorry for the late response!

First your card is detected.

From cli;

Code:
#ifconfig eth0 10.185.3.101        #if this is your IP
#ifconfig -a                       #should show new IP

#route add default gw 10.185.3.1   #your gateway IP
#route -n                          #should show a gw for eth0
If output is correct then try;

Code:
#ping 72.14.207.99                 #google
#ping google                       #see if your dns is working
What is the content of /etc/rc.d/rc.inet1.conf?
 
Old 03-27-2007, 06:48 AM   #9
scolic
LQ Newbie
 
Registered: Mar 2006
Location: Belgrade,Serbia
Distribution: Slackware 14.1 x64
Posts: 5

Rep: Reputation: 0
Unhappy installed slack 11

slack 11 with oldcd kernel out of the box.
although I never learned how to compile a kernel...
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
Realtek network card 8139 under FC4 realcr Linux - Hardware 9 08-18-2005 06:38 PM
realtec 8139 network card problem mandrake 10 frimann Mandriva 6 03-26-2004 03:27 PM
network card configuration problem amrogers3 Linux - Networking 5 02-24-2004 01:09 PM
Slackware 9 PCI network card configuration Harpune Linux - Networking 2 08-26-2003 12:15 PM
Realtek 8139 pci network card and RH 7.3 d4u Linux - Networking 6 09-06-2002 09:25 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Networking

All times are GMT -5. The time now is 12:29 AM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration