Hello all,
This post is about a problem I'm having with my NIC drivers running under Slackare Linux Version 10.2 (Kernel Version 2.4.31). As far as hardware I'm running an ABIT FATAL1TY AA8XE Motherboard, a 256Mb Nvidia Geforce 6600, 1024Mb PC5400 DDR2, and an Intel P4 3.2 Ghz CPU. After a fresh install of Slackware 10.2 on my system I needed to install drivers for my dual onboard Intel Pro 100/1000 Network adaptors. Using Windows I downloaded the appropriate drivers from the ABIT website: e100-3.0.27.tar.gz and e1000-5.3.19.tar.gz, both of which I then transfered to my Linux Partition and extracted to its own directory. I then followed the installation intructions starting with the e100 driver because that is the interface which connects to my cable modem, the other connects to my LAN. I managed to bring the e100 up as eth0 and connect to the internet using insmod, modprobe, and ifconfig. Next I installed the e1000 driver and brought it up as eth1. After Setting up my IP configuration this is what I was left with:
Intel Pro 100: Intel Pro 1000:
Device eth0 eth1
IP Type Assigned by DHCP Set by User
IP Address 71.168.216.1 192.168.0.1
DNS Servers 204.127.198.4
63.240.76.4
Subnet Mask 255.255.248.0 255.255.255.0
DHCP Server 68.87.76.13
MAC Address 00-5D-8D-70-41-4A 00-5D-8D-70-41-4B
Gateway 71.198.216.1

At this point my internet and LAN were both up and running, I also was able to start DHCP server on eth1 which I tested using other computers on my network and confirmed to be working. My problem is that when I restart my computer, the network settings aren't properly reset to what they should be. I can get the module loaded using insmod e100, modprobe e100, and ifconfig, but when I try to set the device number using ifconfig it always mounts the Pro1000 at eth0 and it won't let me set the Pro100 as eth0. The only way to restore internet connectivity after restarting seems to be: to remove all the extracted driver files and also the module files installled by the driver at /lib/modules/KERNEL/drivers/net, then reboot the system and redo driver installation first e100 then e1000.
In a nutshell I'm asking two questions the first is the only one that I need so think of the second as more of an; if you have time thing.

Firstly what do I do to save the configuration so that the network adaptors are set to be loaded and brought up at start up with properly assigned settings for their device number(ethX) and settings as shown above (Dynamic for eth0/pro100 and Assigned Settings for eth1/pro1000)?

My other question is in regards to using my system to share its cable internet connection eth0 with the other computers on my LAN which I am connected to with eth1
As I mentioned I was able to start DHCP server and confirm that it was able to assign IPs to other computers on the LAN however none of my other networked systems are able to access the internet, all IPs, Subnets, etc. are applied as defined in my /etc/dhcpd.conf file but no access to the internet. I get the impression that I might not have set the proper subnet, not sure what number I should be using for that. My understanding is that I should be able to share my eth0 Internet connection with my LAN computers using my other network adaptor, eth1. Do I need to install additional software or do I just need to properly configure my existing network and DHCPD?

This question has probably been answered here or somewhere on the internet before so feel free to post a link if you'd like. I have been reading forums now for a while but this is my first post, thanks in advance for your help.

Sorry for the double post, please remove one of them if you can.

Please use the "Report this post to a moderator" link below your post to bring something to our attention.

The thread will continue here:
http://www.linuxquestions.org/questi...d.php?t=389291