LinuxQuestions.org
Visit Jeremy's Blog.
Go Back   LinuxQuestions.org > Forums > Linux Forums > Linux - Networking
User Name
Password
Linux - Networking This forum is for any issue related to networks or networking.
Routing, network cards, OSI, etc. Anything is fair game.

Notices


Reply
  Search this Thread
Old 02-13-2016, 04:50 PM   #16
Nomrah
LQ Newbie
 
Registered: Feb 2016
Posts: 9

Original Poster
Rep: Reputation: Disabled

Hello, here are the results of the three codes. Also I attempted to get results from the script that you linked me to. I put the text file on my linux mint desktop and checked the "execute" check box, clicked on the file and selected "run" but nothing happens. Would it make a difference that I'm running Mint under a live session and not a full install?

lsusb
Code:
mint@mint ~ $ lsusb
Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 006: ID 0930:6545 Toshiba Corp. Kingston DataTraveler 102 Flash Drive / HEMA Flash Drive 2 GB / PNY Attache 4GB Stick
Bus 004 Device 007: ID 20f4:648b TRENDnet TEW-648UBM 802.11n 150Mbps Micro Wireless N Adapter [Realtek RTL8188CUS]
Bus 004 Device 004: ID 046d:c21d Logitech, Inc. F310 Gamepad [XInput Mode]
Bus 004 Device 003: ID 090c:1000 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) Flash Drive
Bus 004 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 003: ID 1c4f:0034 SiGma Micro 
Bus 006 Device 002: ID 1c4f:0002 SiGma Micro Keyboard TRACER Gamma Ivory
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
lsmod
Code:
mint@mint ~ $ lsmod
Module                  Size  Used by
arc4                   16384  2 
rtl8192cu              69632  0 
rtl_usb                20480  1 rtl8192cu
rtl8192c_common        53248  1 rtl8192cu
rtlwifi                73728  3 rtl_usb,rtl8192c_common,rtl8192cu
mac80211              708608  3 rtl_usb,rtlwifi,rtl8192cu
cfg80211              524288  2 mac80211,rtlwifi
nls_utf8               16384  1 
isofs                  40960  1 
dm_crypt               24576  0 
snd_hda_codec_via      32768  1 
snd_hda_codec_generic    69632  1 snd_hda_codec_via
snd_hda_codec_hdmi     53248  1 
snd_hda_intel          36864  6 snd_hda_codec_hdmi
snd_hda_controller     32768  1 snd_hda_intel
snd_hda_codec         143360  5 snd_hda_codec_hdmi,snd_hda_codec_via,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
snd_hwdep              20480  1 snd_hda_codec
snd_pcm               106496  4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
kvm                   479232  0 
crct10dif_pclmul       16384  0 
snd_seq_midi           16384  0 
crc32_pclmul           16384  0 
snd_seq_midi_event     16384  1 snd_seq_midi
ghash_clmulni_intel    16384  0 
dm_multipath           24576  0 
aesni_intel           172032  0 
snd_rawmidi            32768  1 snd_seq_midi
scsi_dh                16384  1 dm_multipath
aes_x86_64             20480  1 aesni_intel
snd_seq                65536  2 snd_seq_midi_event,snd_seq_midi
xpad                   24576  0 
lrw                    16384  1 aesni_intel
joydev                 20480  0 
ff_memless             16384  1 xpad
gf128mul               16384  1 lrw
snd_seq_device         16384  3 snd_seq,snd_rawmidi,snd_seq_midi
glue_helper            16384  1 aesni_intel
snd_timer              32768  2 snd_pcm,snd_seq
ablk_helper            16384  1 aesni_intel
cryptd                 20480  3 ghash_clmulni_intel,aesni_intel,ablk_helper
snd                    86016  21 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_via,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel,snd_seq_device
edac_core              53248  0 
edac_mce_amd           24576  0 
k10temp                16384  0 
serio_raw              16384  0 
bnep                   20480  2 
soundcore              16384  2 snd,snd_hda_codec
fam15h_power           16384  0 
shpchp                 40960  0 
i2c_piix4              24576  0 
rfcomm                 69632  0 
ppdev                  20480  0 
mac_hid                16384  0 
8250_fintek            16384  0 
asus_atk0110           20480  0 
bluetooth             491520  10 bnep,rfcomm
parport_pc             32768  1 
lp                     20480  0 
parport                45056  3 lp,ppdev,parport_pc
binfmt_misc            20480  1 
squashfs               49152  1 
overlay                45056  1 
nls_iso8859_1          16384  2 
dm_mirror              24576  0 
dm_region_hash         24576  1 dm_mirror
dm_log                 20480  2 dm_region_hash,dm_mirror
hid_generic            16384  0 
usbhid                 53248  0 
hid                   110592  2 hid_generic,usbhid
uas                    24576  0 
usb_storage            69632  3 uas
pata_acpi              16384  0 
amdkfd                 81920  1 
amd_iommu_v2           20480  1 amdkfd
radeon               1556480  3 
i2c_algo_bit           16384  1 radeon
ttm                    94208  1 radeon
psmouse               114688  0 
drm_kms_helper        126976  1 radeon
drm                   344064  6 ttm,drm_kms_helper,radeon
pata_atiixp            16384  0 
r8169                  81920  0 
ahci                   36864  1 
libahci                32768  1 ahci
mii                    16384  1 r8169
wmi                    20480  0
iwconfig
Code:
mint@mint ~ $ iwconfig
eth0      no wireless extensions.

wlan0     IEEE 802.11bgn  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
          Retry short limit:7   RTS thr=2347 B   Fragment thr:off
          Power Management:off
          
lo        no wireless extensions.
 
Old 02-13-2016, 05:48 PM   #17
ardvark71
LQ Veteran
 
Registered: Feb 2015
Location: USA
Distribution: Lubuntu 14.04, 22.04, Windows 8.1 and 10
Posts: 6,282
Blog Entries: 4

Rep: Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842
Quote:
Originally Posted by Ztcoracat View Post
Thanks for joining ardvark71-
You're welcome
 
Old 02-13-2016, 05:59 PM   #18
Ztcoracat
LQ Guru
 
Registered: Dec 2011
Distribution: Slackware, MX 18
Posts: 9,484
Blog Entries: 15

Rep: Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176
The other usb wifi dongle shows up.

Code:
TRENDnet TEW-648UBM 802.11n 150Mbps Micro Wireless N Adapter [Realtek RTL8188CUS]
http://linux-drivers.net/index.php?p...,%20150Mbps%29

http://linux-drivers.net/download3.p...,%20150Mbps%29
 
Old 02-13-2016, 06:05 PM   #19
Ztcoracat
LQ Guru
 
Registered: Dec 2011
Distribution: Slackware, MX 18
Posts: 9,484
Blog Entries: 15

Rep: Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176Reputation: 1176
Quote:
Would it make a difference that I'm running Mint under a live session and not a full install?
Running that script should have produced a file called "wireless-info.txt" in your home directory.
So....if your running Mint Live and it's not installed to the HDD I speculate that it would not show in the Home directory. Look and see.
 
Old 02-13-2016, 06:10 PM   #20
ardvark71
LQ Veteran
 
Registered: Feb 2015
Location: USA
Distribution: Lubuntu 14.04, 22.04, Windows 8.1 and 10
Posts: 6,282
Blog Entries: 4

Rep: Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842
Quote:
Originally Posted by Nomrah View Post
Would it make a difference that I'm running Mint under a live session and not a full install?
Hi...

No, it shouldn't make a difference. If you can connect to the internet using an ethernet cord (while using Mint,) method #1 would be a lot easier.

Thank you also for the other results, would you also include the results for...

Code:
dmesg | grep -iC 3 "wlan0"
Thanks!

Regards...
 
Old 02-14-2016, 02:42 PM   #21
Nomrah
LQ Newbie
 
Registered: Feb 2016
Posts: 9

Original Poster
Rep: Reputation: Disabled
output for dmesg | grep -iC 3 "wlan0"

Code:
mint@mint ~ $ dmesg | grep -iC 3 "wlan0"
[   40.804780] rtl_usb: reg 0x33, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x9f80
[   40.895588] rtl_usb: reg 0x33, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x5
[   40.978138] rtl_usb: reg 0x33, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0xa100
[   45.547982] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   57.388751] systemd-hostnamed[3155]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[   64.222225] wlan0: authenticate with c8:d7:19:a7:ce:f7
[   64.245425] wlan0: send auth to c8:d7:19:a7:ce:f7 (try 1/3)
[   64.346056] wlan0: send auth to c8:d7:19:a7:ce:f7 (try 2/3)
[   64.403484] wlan0: authenticated
[   64.406105] wlan0: associate with c8:d7:19:a7:ce:f7 (try 1/3)
[   64.445636] wlan0: RX AssocResp from c8:d7:19:a7:ce:f7 (capab=0x411 status=0 aid=4)
[   64.446509] wlan0: associated
[   64.446517] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   74.195484] wlan0: Connection to AP c8:d7:19:a7:ce:f7 lost
[   74.214259] cfg80211: Calling CRDA to update world regulatory domain
[   74.245892] cfg80211: World regulatory domain updated:
[   74.245896] cfg80211:  DFS Master region: unset
--
[   74.245902] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
[   74.245904] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   74.245905] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
[   75.022633] wlan0: authenticate with c8:d7:19:a7:ce:f7
[   75.046034] wlan0: send auth to c8:d7:19:a7:ce:f7 (try 1/3)
[   75.146482] wlan0: send auth to c8:d7:19:a7:ce:f7 (try 2/3)
[   75.250563] wlan0: send auth to c8:d7:19:a7:ce:f7 (try 3/3)
[   75.354644] wlan0: authentication with c8:d7:19:a7:ce:f7 timed out
 
Old 02-14-2016, 05:57 PM   #22
ardvark71
LQ Veteran
 
Registered: Feb 2015
Location: USA
Distribution: Lubuntu 14.04, 22.04, Windows 8.1 and 10
Posts: 6,282
Blog Entries: 4

Rep: Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842
Hi...

Thank you but I still like to see the results from the script.

However, one quick option you can try if you're not using IPv6 is to set Mint to ignore it using the instructions here (on the right hand side.)

Let us know if that helps.

Regards...
 
Old 02-14-2016, 07:56 PM   #23
Nomrah
LQ Newbie
 
Registered: Feb 2016
Posts: 9

Original Poster
Rep: Reputation: Disabled
Hello, sorry that I have not been able to fetch results from that script, I cannot get a wired connection to this computer and the manual no connection procedure does not seem to get me what I want.

I went ahead and set IPv6 to ignore and saved the changes and disconnected and reconnected the trendnet adapter into the usb port afterwards but the issues persisted with no change.
 
Old 02-14-2016, 08:26 PM   #24
ardvark71
LQ Veteran
 
Registered: Feb 2015
Location: USA
Distribution: Lubuntu 14.04, 22.04, Windows 8.1 and 10
Posts: 6,282
Blog Entries: 4

Rep: Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842
Quote:
Originally Posted by Nomrah View Post
Hello, sorry that I have not been able to fetch results from that script, I cannot get a wired connection to this computer and the manual no connection procedure does not seem to get me what I want.
Hi...

The information from the script would be very helpful, so if you can find a way...

Quote:
Originally Posted by Nomrah View Post
I went ahead and set IPv6 to ignore and saved the changes and disconnected and reconnected the trendnet adapter into the usb port afterwards but the issues persisted with no change.
Did you reboot Linux after you made the change? That might make a difference.

EDIT: It might be easier to just purchase a more Linux compatible adapter, like the ones mentioned here.

Regards...

Last edited by ardvark71; 02-14-2016 at 08:37 PM. Reason: Added information.
 
Old 02-14-2016, 09:04 PM   #25
Nomrah
LQ Newbie
 
Registered: Feb 2016
Posts: 9

Original Poster
Rep: Reputation: Disabled
I did not try to reboot Linux after the changes because everything resets (to my knowledge) to default every time I restart and boot a live session from the bios. I'll give it another try just to make sure. If I ever get the chance to get a wired connection to get that script I will let you know.

I'll definitely keep my possibilities open for purchasing a more Linux compatible adapter if the time presents itself, thank you for the link. For now I think I'll put my Linux ventures on hold for now. Thanks for the sincere efforts you all put forth attempting to assist me with the situation, it is much appreciated.
 
Old 02-14-2016, 09:31 PM   #26
ardvark71
LQ Veteran
 
Registered: Feb 2015
Location: USA
Distribution: Lubuntu 14.04, 22.04, Windows 8.1 and 10
Posts: 6,282
Blog Entries: 4

Rep: Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842
Quote:
Originally Posted by Nomrah View Post
I did not try to reboot Linux after the changes because everything resets (to my knowledge) to default every time I restart and boot a live session from the bios. I'll give it another try just to make sure.
That's right, I forgot about that. My apologies.

Regards...
 
Old 02-14-2016, 10:01 PM   #27
ardvark71
LQ Veteran
 
Registered: Feb 2015
Location: USA
Distribution: Lubuntu 14.04, 22.04, Windows 8.1 and 10
Posts: 6,282
Blog Entries: 4

Rep: Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842Reputation: 842
Quote:
Originally Posted by Nomrah View Post
Thanks for the sincere efforts you all put forth attempting to assist me with the situation, it is much appreciated.
You're welcome, I'm sorry I couldn't be of more help.

Regards...
 
Old 02-17-2016, 03:27 PM   #28
nini09
Senior Member
 
Registered: Apr 2009
Posts: 1,850

Rep: Reputation: 161Reputation: 161
What's wifi configuration? Do you turn on encryption key? Encryption is enabled on AP side.
 
  


Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off



Similar Threads
Thread Thread Starter Forum Replies Last Post
netgear wna3100 usb not working dritz69 Linux - Newbie 7 12-12-2013 11:12 PM
[SOLVED] Netgear WNA3100 won't work with bcmwlhigh5 or 6? oxman2001 Linux - Hardware 1 09-12-2012 04:36 PM
Netgear WNA3100 not working with bcmwlhigh5 or 6. oxman2001 Linux - Newbie 0 07-20-2012 09:03 PM
Making a Netgear WNA3100 adapter work with Ubuntu 12 Basilios Ubuntu 5 06-10-2012 01:56 PM
USB Virtual Network Adapter Internet Connection Sharing Suse 10.2 and Windows, How??? tfm1 Linux - Networking 1 12-25-2006 02:41 PM

LinuxQuestions.org > Forums > Linux Forums > Linux - Networking

All times are GMT -5. The time now is 12:51 PM.

Main Menu
Advertisement
My LQ
Write for LQ
LinuxQuestions.org is looking for people interested in writing Editorials, Articles, Reviews, and more. If you'd like to contribute content, let us know.
Main Menu
Syndicate
RSS1  Latest Threads
RSS1  LQ News
Twitter: @linuxquestions
Open Source Consulting | Domain Registration