(posting again because I don't see the original).
Hi all. I usually google my problem before I bother others with them, and this is probably on it's 4th day of trying to debug, and I simply can't take it anymore (no hair left). Also, I'm fairly new to this, so I must apoligize ahead of time, if this is a n00b thing (and I hope it is).
A new install of Mandriva (2007.0). Everything works great.
I've installed a ci$co VPN client (and am using the profile supplied by my work). When I start VPN, I get a tunnel, I'm assigned a client address IP of 10.1.15.*, and I can see the server address,
ie;
Code:
Your VPN connection is secure.
VPN tunnel information.
Client address: 10.1.15.6
Server address: 64.128.24.7
Encryption: 168-bit 3-DES
Authentication: HMAC-MD5
IP Compression: None
NAT passthrough is active on port UDP 10000
Local LAN Access is disabled
but when I try to ping anyone in that same area 10.1.15.*, I get
" From 10.1.15.6 icmp_seq=1 Destination Host Unreachable "
Now, this is ONLY in that area. I can still go everywhere else on the internet, just not in this group (I know there are multiple systems in this group).
Is this a firewall coniguration this? A NAT configuration thing? To my knowledge, I have not configured ANYTHING on the new install yet (its' all default, so firewall, etc is default).
Here are my goodies;
PHP Code:
[name-hidden@adsl-71-145-143-67 /]$ netstat -r
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
vpnaustin.sigma adsl-71-145-143 255.255.255.255 UGH 0 0 0 eth0
192.168.100.0 10.1.15.6 255.255.255.0 UG 0 0 0 cipsec0
172.16.100.0 10.1.15.6 255.255.255.0 UG 0 0 0 cipsec0
71.145.143.0 * 255.255.255.0 U 0 0 0 eth0
10.1.0.0 * 255.255.240.0 U 0 0 0 cipsec0
10.2.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.35.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.3.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.1.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.6.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.7.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.4.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.20.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.5.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.254.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
10.9.0.0 10.1.15.6 255.255.0.0 UG 0 0 0 cipsec0
default adsl-71-145-143 0.0.0.0 UG 0 0 0 eth0
ifconfig;
PHP Code:
cipsec0 Link encap:Ethernet HWaddr 00:0B:FC:F8:01:8F
inet addr:10.1.15.6 Mask:255.255.240.0
inet6 addr: fe80::20b:fcff:fef8:18f/64 Scope:Link
UP RUNNING NOARP MTU:1356 Metric:1
RX packets:144 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:742 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:16744 (16.3 KiB) TX bytes:0 (0.0 b)
eth0 Link encap:Ethernet HWaddr 00:0D:61:06:6C:76
inet addr:71.145.143.67 Bcast:71.145.143.255 Mask:255.255.255.0
inet6 addr: fe80::20d:61ff:fe06:6c76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:33776 errors:0 dropped:0 overruns:0 frame:0
TX packets:38043 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13572390 (12.9 MiB) TX bytes:3280497 (3.1 MiB)
Interrupt:17 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:49758 errors:0 dropped:0 overruns:0 frame:0
TX packets:49758 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4423952 (4.2 MiB) TX bytes:4423952 (4.2 MiB)
(FWIW, you can see that cipsec0 has dropped all TX packets.)
A look into my resolv.conf yeilds; (why the redundant nameserver?)
PHP Code:
domain sigmatel.com
nameserver 192.168.0.1
nameserver 192.168.0.1
search sigmatel.com dsl.austtx.sbcglobal.net
-Thanks
