MSI Wireless 11g CardBus Card CB54G
i would like known where i canīt get drivers to my wireless card msi CB54G for slackware, if exists. Or any another solution.
Thanks |
We'll need to know the chipset to offer much help.
Try lspci -v or look in /var/log/messages for clues as to the innards. |
sadly my ac adaptor broke up. i will give that information as soon as possible. thanks for the help.
|
CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
Subsystem: Unknown device 17c0:3001 Flags: bus master, medium devsel, latency 168, IRQ 11 Memory at 1e000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=03, sec-latency=176 Memory window 0: 1e400000-1e7ff000 (prefetchable) Memory window 1: 1e800000-1ebff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff 16-bit legacy interface ports at 0001 this is my pcmcia ports information, can you help me now?? |
That's the information for the cardbus controller, not the card. Try again and list the entire output of lspci -v
The only CB54G listed in the AbsoluteValue Systems http://www.linux-wlan.org/docs/wlan_adapters.html.gz list is branded as a Corega and uses the PrismGT chipset. If that's the same card, the driver at prism54.org should work. |
you can see all the information for my card on this page
http://www.msimiami.com/portugues/pr...CB54G_port.htm |
Which says nothing about the chipset.
I've given you as much help as I can based on what you've given me. Good luck with it. |
CB54G output from lspci
I noticed this site [linuxquestions.org] has a lot of cool info...
I keep popping up in it from google every time I have a problem :) Just thought I'd post the lspci output on the CB54G in case it would help anybody. To date, I have it running in Linux... *BUT* I had to use the Linuxant driverloader [http://linuxant.com] in order to do so. I don't know what I'm going to do in 30 days... Probably going to get a new card :P I've been trying to get ndiswrapper to work with many different vendors' BCM4306 chipset drivers... all without success. If I actually get it going [with ndiswrapper] I'll post... Anyway... here's the output from lspci -vv [that's two v's not one w] :) 0000:03:00.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03) Subsystem: Micro-Star International Co., Ltd.: Unknown device 6819 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 10800000 (32-bit, non-prefetchable) [size=8K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- |
All times are GMT -5. The time now is 02:39 PM. |