| faq885 |
03-24-2011 01:03 PM |
Hi, here is the dmseg output from mint 10 live cd. I you want only a specific part of the output tell me, I don't know what I have to look for in this output. At the end there's info about the A4Tech mouse.
Thanks!!
Code:
[ 5.408788] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 5.408889] pcieport 0000:00:1c.1: setting latency timer to 64
[ 5.408935] alloc irq_desc for 41 on node -1
[ 5.408936] alloc kstat_irqs on node -1
[ 5.408945] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[ 5.409043] pcieport 0000:00:1c.3: setting latency timer to 64
[ 5.409088] alloc irq_desc for 42 on node -1
[ 5.409090] alloc kstat_irqs on node -1
[ 5.409098] pcieport 0000:00:1c.3: irq 42 for MSI/MSI-X
[ 5.409194] pcieport 0000:00:1c.4: setting latency timer to 64
[ 5.409239] alloc irq_desc for 43 on node -1
[ 5.409241] alloc kstat_irqs on node -1
[ 5.409250] pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X
[ 5.409358] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.409625] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 5.409697] intel_idle: MWAIT substates: 0x22220
[ 5.409699] intel_idle: does not run on family 6 model 23
[ 5.409847] ACPI: AC Adapter [ADP0] (on-line)
[ 5.409942] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 5.409947] ACPI: Power Button [PWRB]
[ 5.409984] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 5.412061] ACPI: Lid Switch [LID0]
[ 5.412119] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.412122] ACPI: Power Button [PWRF]
[ 5.412312] ACPI: Fan [FAN] (on)
[ 5.412854] ACPI: acpi_idle registered with cpuidle
[ 5.413072] Monitor-Mwait will be used to enter C-1 state
[ 5.413093] Monitor-Mwait will be used to enter C-2 state
[ 5.413098] Marking TSC unstable due to TSC halts in idle
[ 5.413126] Switching to clocksource hpet
[ 5.420361] thermal LNXTHERM:01: registered as thermal_zone0
[ 5.420368] ACPI: Thermal Zone [THRM] (47 C)
[ 5.420450] ERST: Table is not found!
[ 5.421300] Linux agpgart interface v0.103
[ 5.421322] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 5.421639] ACPI: Battery Slot [BAT0] (battery present)
[ 5.422560] brd: module loaded
[ 5.423032] loop: module loaded
[ 5.423454] Fixed MDIO Bus: probed
[ 5.423481] PPP generic driver version 2.4.2
[ 5.423512] tun: Universal TUN/TAP device driver, 1.6
[ 5.423514] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 5.423580] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.423603] ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 5.423624] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 5.423628] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 5.423657] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 5.423691] ehci_hcd 0000:00:1a.7: debug port 1
[ 5.427576] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[ 5.427594] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xd8804c00
[ 5.450016] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 5.450123] hub 1-0:1.0: USB hub found
[ 5.450129] hub 1-0:1.0: 4 ports detected
[ 5.450197] alloc irq_desc for 23 on node -1
[ 5.450199] alloc kstat_irqs on node -1
[ 5.450205] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 5.450216] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 5.450219] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 5.450249] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 5.450279] ehci_hcd 0000:00:1d.7: debug port 1
[ 5.454159] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 5.454172] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd8804800
[ 5.470019] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 5.470117] hub 2-0:1.0: USB hub found
[ 5.470121] hub 2-0:1.0: 8 ports detected
[ 5.470194] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.470207] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.470252] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.470259] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 5.470262] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 5.470295] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 5.470331] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000070e0
[ 5.470434] hub 3-0:1.0: USB hub found
[ 5.470438] hub 3-0:1.0: 2 ports detected
[ 5.470498] alloc irq_desc for 21 on node -1
[ 5.470500] alloc kstat_irqs on node -1
[ 5.470504] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 5.470510] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 5.470513] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 5.470544] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 5.470578] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000070c0
[ 5.470683] hub 4-0:1.0: USB hub found
[ 5.470687] hub 4-0:1.0: 2 ports detected
[ 5.470750] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 5.470757] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 5.470760] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 5.470788] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 5.470813] uhci_hcd 0000:00:1d.0: irq 23, io base 0x000070a0
[ 5.470917] hub 5-0:1.0: USB hub found
[ 5.470921] hub 5-0:1.0: 2 ports detected
[ 5.470979] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 5.470985] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 5.470988] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 5.471016] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 5.471042] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00007080
[ 5.471147] hub 6-0:1.0: USB hub found
[ 5.471151] hub 6-0:1.0: 2 ports detected
[ 5.471207] uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 5.471214] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 5.471217] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 5.471255] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 5.471282] uhci_hcd 0000:00:1d.2: irq 16, io base 0x00007060
[ 5.471390] hub 7-0:1.0: USB hub found
[ 5.471394] hub 7-0:1.0: 2 ports detected
[ 5.471452] alloc irq_desc for 18 on node -1
[ 5.471454] alloc kstat_irqs on node -1
[ 5.471458] uhci_hcd 0000:00:1d.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 5.471465] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 5.471468] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 5.471496] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8
[ 5.471531] uhci_hcd 0000:00:1d.3: irq 18, io base 0x00007040
[ 5.471636] hub 8-0:1.0: USB hub found
[ 5.471642] hub 8-0:1.0: 2 ports detected
[ 5.471744] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12
[ 5.498631] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.498638] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 5.498693] mice: PS/2 mouse device common for all mice
[ 5.498812] rtc_cmos 00:03: RTC can wake from S4
[ 5.498846] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 5.498877] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 5.498964] device-mapper: uevent: version 1.0.3
[ 5.499039] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 5.499102] device-mapper: multipath: version 1.1.1 loaded
[ 5.499105] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 5.499279] cpuidle: using governor ladder
[ 5.499675] cpuidle: using governor menu
[ 5.499926] TCP cubic registered
[ 5.500069] NET: Registered protocol family 10
[ 5.500400] lo: Disabled Privacy Extensions
[ 5.500573] NET: Registered protocol family 17
[ 5.501348] PM: Resume from disk failed.
[ 5.501361] registered taskstats version 1
[ 5.501844] Magic number: 3:58:840
[ 5.501965] rtc_cmos 00:03: setting system clock to 2011-03-24 14:50:39 UTC (1300978239)
[ 5.501968] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.501969] EDD information not available.
[ 5.502057] Freeing unused kernel memory: 908k freed
[ 5.502364] Write protecting the kernel read-only data: 10240k
[ 5.502569] Freeing unused kernel memory: 416k freed
[ 5.502844] Freeing unused kernel memory: 1644k freed
[ 5.520918] udev[86]: starting version 163
[ 5.532448] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 5.574531] sdhci: Secure Digital Host Controller Interface driver
[ 5.574534] sdhci: Copyright(c) Pierre Ossman
[ 5.575744] sdhci-pci 0000:04:00.0: SDHCI controller found [1180:e822] (rev 1)
[ 5.575773] sdhci-pci 0000:04:00.0: PCI INT D -> GSI 18 (level, low) -> IRQ 18
[ 5.576815] sdhci-pci 0000:04:00.0: Will use DMA mode even though HW doesn't fully claim to support it.
[ 5.576824] sdhci-pci 0000:04:00.0: setting latency timer to 64
[ 5.577873] Registered led device: mmc0::
[ 5.587482] agpgart-intel 0000:00:00.0: Intel GM45 Chipset
[ 5.588722] agpgart-intel 0000:00:00.0: detected 131068K stolen memory, trimming to 32768K
[ 5.622916] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 5.622961] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.623089] r8169 0000:02:00.0: setting latency timer to 64
[ 5.623232] alloc irq_desc for 44 on node -1
[ 5.623234] alloc kstat_irqs on node -1
[ 5.623272] r8169 0000:02:00.0: irq 44 for MSI/MSI-X
[ 5.623804] r8169 0000:02:00.0: eth0: RTL8102e at 0xffffc9000063e000, 00:1e:33:f8:4f:2a, XID 04c00000 IRQ 44
[ 5.689494] mmc0: SDHCI controller on PCI [0000:04:00.0] using DMA
[ 5.716733] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 5.716768] ahci 0000:00:1f.2: version 3.0
[ 5.716788] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 5.716837] alloc irq_desc for 45 on node -1
[ 5.716840] alloc kstat_irqs on node -1
[ 5.716855] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
[ 5.716950] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[ 5.716953] ahci 0000:00:1f.2: flags: 64bit ncq sntf led clo pmp pio slum part ccc sxs
[ 5.716959] ahci 0000:00:1f.2: setting latency timer to 64
[ 5.717264] [drm] Initialized drm 1.1.0 20060810
[ 5.717731] scsi0 : ahci
[ 5.717886] scsi1 : ahci
[ 5.717980] scsi2 : ahci
[ 5.718070] scsi3 : ahci
[ 5.718162] scsi4 : ahci
[ 5.718260] scsi5 : ahci
[ 5.718620] ata1: SATA max UDMA/133 abar m2048@0xd8804000 port 0xd8804100 irq 45
[ 5.718624] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 45
[ 5.718626] ata3: DUMMY
[ 5.718627] ata4: DUMMY
[ 5.718630] ata5: SATA max UDMA/133 abar m2048@0xd8804000 port 0xd8804300 irq 45
[ 5.718634] ata6: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 45
[ 5.770076] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 6.060064] ata1: SATA link down (SStatus 0 SControl 300)
[ 6.060102] ata5: SATA link down (SStatus 0 SControl 300)
[ 6.230057] usb 2-3: new high speed USB device using ehci_hcd and address 2
[ 6.389170] Initializing USB Mass Storage driver...
[ 6.389296] scsi6 : usb-storage 2-3:1.0
[ 6.389374] usbcore: registered new interface driver usb-storage
[ 6.389376] USB Mass Storage support registered.
[ 6.640036] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 6.640057] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 6.644126] ata6.00: ATAPI: HL-DT-ST DVDRAM GT20F, ET10, max UDMA/133
[ 6.648998] ata6.00: configured for UDMA/133
[ 6.820044] usb 6-2: new full speed USB device using uhci_hcd and address 2
[ 7.044907] usbcore: registered new interface driver hiddev
[ 7.048537] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input4
[ 7.048654] generic-usb 0003:09DA:054F.0001: input,hiddev96,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1d.1-2/input0
[ 7.050475] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.1/input/input5
[ 7.050556] generic-usb 0003:09DA:054F.0002: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1d.1-2/input1
[ 7.050570] usbcore: registered new interface driver usbhid
[ 7.050572] usbhid: USB HID core driver
[ 7.063189] ata2.00: ATA-8: TOSHIBA MK4055GSX, FG011M, max UDMA/100
[ 7.063195] ata2.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 7.064075] ata2.00: configured for UDMA/100
[ 7.064266] scsi 1:0:0:0: Direct-Access ATA TOSHIBA MK4055GS FG01 PQ: 0 ANSI: 5
[ 7.064457] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 7.064553] sd 1:0:0:0: [sda] 781422768 512-byte logical blocks: (400 GB/372 GiB)
[ 7.064603] sd 1:0:0:0: [sda] Write Protect is off
[ 7.064606] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 7.064627] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.064756] sda:
[ 7.067993] scsi 5:0:0:0: CD-ROM HL-DT-ST DVDRAM GT20F ET10 PQ: 0 ANSI: 5
[ 7.079224] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 7.079227] Uniform CD-ROM driver Revision: 3.20
[ 7.079318] sr 5:0:0:0: Attached scsi CD-ROM sr0
[ 7.079370] sr 5:0:0:0: Attached scsi generic sg1 type 5
[ 7.114840] sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
[ 7.151836] sd 1:0:0:0: [sda] Attached SCSI disk
[ 7.167672] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.167677] i915 0000:00:02.0: setting latency timer to 64
[ 7.240880] [drm] detected 127M stolen memory, trimming to 32M
[ 7.240989] alloc irq_desc for 46 on node -1
[ 7.240992] alloc kstat_irqs on node -1
[ 7.241002] i915 0000:00:02.0: irq 46 for MSI/MSI-X
[ 7.241017] [drm] set up 32M of stolen space
[ 7.241167] [drm:init_ring_common] *ERROR* render ring head not reset to zero ctl 00000000 head 02001000 tail 00000000 start 02001000
[ 7.241172] [drm:init_ring_common] *ERROR* render ring head forced to zero ctl 00000000 head 00000000 tail 00000000 start 02001000
[ 7.366939] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 7.382380] scsi 6:0:0:0: Direct-Access Corsair Flash Voyager 1100 PQ: 0 ANSI: 0 CCS
[ 7.383193] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 7.383863] sd 6:0:0:0: [sdb] 7864320 512-byte logical blocks: (4.02 GB/3.75 GiB)
[ 7.384888] sd 6:0:0:0: [sdb] Write Protect is off
[ 7.384891] sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 7.384894] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 7.387984] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 7.387990] sdb: sdb1
[ 7.390358] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 7.390361] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 7.711266] Skipping EDID probe due to cached edid
[ 8.092896] Console: switching to colour frame buffer device 170x48
[ 8.095592] fb0: inteldrmfb frame buffer device
[ 8.095593] drm: registered panic notifier
[ 8.095597] Slow work thread pool: Starting up
[ 8.095721] Slow work thread pool: Ready
[ 8.106343] acpi device:03: registered as cooling_device3
[ 8.106841] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 8.106890] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 8.106934] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 8.361269] Skipping EDID probe due to cached edid
[ 8.472131] Btrfs loaded
[ 8.476546] xor: automatically using best checksumming function: generic_sse
[ 8.520007] generic_sse: 8356.000 MB/sec
[ 8.520009] xor: using function: generic_sse (8356.000 MB/sec)
[ 8.522586] device-mapper: dm-raid45: initialized v0.2594b
[ 9.631305] EXT4-fs (sda5): INFO: recovery required on readonly filesystem
[ 9.631309] EXT4-fs (sda5): write access will be enabled during recovery
[ 9.668409] EXT4-fs (sda5): recovery complete
[ 9.668735] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 10.457042] aufs 2-standalone.tree-35-rcN-20100705
[ 10.469198] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 19.883515] Adding 4096536k swap on /dev/sda6. Priority:-1 extents:1 across:4096536k
[ 20.081762] udev[1499]: starting version 163
[ 20.355778] rtllib_crypt: registered algorithm 'NULL'
[ 20.355782] rtllib_crypt: registered algorithm 'TKIP'
[ 20.355784] rtllib_crypt: registered algorithm 'CCMP'
[ 20.355786] rtllib_crypt: registered algorithm 'WEP'
[ 20.355787]
[ 20.355788] Linux kernel driver for RTL8192 based WLAN cards
[ 20.355790] Copyright (c) 2007-2008, Realsil Wlan Driver
[ 20.356427] rtl819xSE 0000:03:00.0: power state changed by ACPI to D0
[ 20.356491] rtl819xSE 0000:03:00.0: power state changed by ACPI to D0
[ 20.356502] rtl819xSE 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 20.356510] rtl819xSE 0000:03:00.0: setting latency timer to 64
[ 20.432485] Memory mapped space start: 0xd6700000
[ 20.432554] Adapter(8192SE) is found - DeviceID=8172
[ 20.433778] GetPciBusInfo(): Find Device(10EC:8172) bus=3 dev=0, func=0
[ 20.434909] GetPciBridegInfo : Find Device(8086:2942) bus=0 dev=28, func=1
[ 20.434911] Pci Bridge Vendor is found index: 0
[ 20.434913] Pci Bridge Vendor is 8086
[ 20.469514] =========>dm_InitRateAdaptiveMask: bUseRAMask=0
[ 20.660161] r8169 0000:02:00.0: eth0: link down
[ 20.661152] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.707461] Linux video capture interface: v2.00
[ 20.728510] uvcvideo: Found UVC 1.00 device USB2.0 UVC WebCam (04f2:b128)
[ 20.738691] input: USB2.0 UVC WebCam as /devices/pci0000:00/0000:00:1a.7/usb1/1-2/1-2:1.0/input/input7
[ 20.738751] usbcore: registered new interface driver uvcvideo
[ 20.738753] USB Video Class driver (v0.1.0)
[ 20.946757] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
[ 20.946765] ===>rtllib_start_scan()
[ 20.946947] =====>rtl8192_set_chan()====ch:11
[ 20.948825] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 21.050075] =====>rtl8192_set_chan()====ch:12
[ 21.160030] =====>rtl8192_set_chan()====ch:13
[ 21.181578] alloc irq_desc for 22 on node -1
[ 21.181581] alloc kstat_irqs on node -1
[ 21.181590] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 21.181689] alloc irq_desc for 47 on node -1
[ 21.181691] alloc kstat_irqs on node -1
[ 21.181704] HDA Intel 0000:00:1b.0: irq 47 for MSI/MSI-X
[ 21.181742] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 21.233896] =====>rtl8192_set_chan()====ch:1
[ 21.345471] hda_codec: ALC272: BIOS auto-probing.
[ 21.351467] =====>rtl8192_set_chan()====ch:2
[ 21.422425] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1e0b1, caps: 0xd04731/0xa40000/0xa0000
[ 21.422430] synaptics: Toshiba Satellite A505 detected, limiting rate to 40pps.
[ 21.471278] =====>rtl8192_set_chan()====ch:3
[ 21.486547] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[ 21.581392] Skipping EDID probe due to cached edid
[ 21.591464] =====>rtl8192_set_chan()====ch:4
[ 21.640209] Skipping EDID probe due to cached edid
[ 21.711317] =====>rtl8192_set_chan()====ch:5
[ 21.831312] =====>rtl8192_set_chan()====ch:6
[ 21.951317] =====>rtl8192_set_chan()====ch:7
[ 22.030659] lp: driver loaded but no devices found
[ 22.048194] ppdev: user-space parallel port driver
[ 22.071308] =====>rtl8192_set_chan()====ch:8
[ 22.191287] =====>rtl8192_set_chan()====ch:9
[ 22.310025] =====>rtl8192_set_chan()====ch:10
[ 22.431335] =====>rtl8192_set_chan()====ch:11
[ 22.551317] =====>rtl8192_set_chan()====ch:12
[ 22.671319] =====>rtl8192_set_chan()====ch:13
[ 23.444205] ===>rtllib_wx_set_power(): power disable
[ 23.650220] Skipping EDID probe due to cached edid
[ 23.700109] Skipping EDID probe due to cached edid
[ 23.761332] Skipping EDID probe due to cached edid
[ 23.820116] Skipping EDID probe due to cached edid
[ 24.196638] ===>rtllib_wx_set_power(): power disable
[ 25.631361] Skipping EDID probe due to cached edid
[ 29.240073] Skipping EDID probe due to cached edid
[ 41.134356] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
[ 41.134442] =====>rtl8192_set_chan()====ch:1
[ 41.251382] =====>rtl8192_set_chan()====ch:2
[ 41.371277] =====>rtl8192_set_chan()====ch:3
[ 41.491277] =====>rtl8192_set_chan()====ch:4
[ 41.611275] =====>rtl8192_set_chan()====ch:5
[ 41.731277] =====>rtl8192_set_chan()====ch:6
[ 41.850487] =====>rtl8192_set_chan()====ch:7
[ 41.961277] =====>rtl8192_set_chan()====ch:8
[ 42.080027] =====>rtl8192_set_chan()====ch:9
[ 42.200026] =====>rtl8192_set_chan()====ch:10
[ 42.320028] =====>rtl8192_set_chan()====ch:11
[ 42.440027] =====>rtl8192_set_chan()====ch:12
[ 42.560063] =====>rtl8192_set_chan()====ch:13
[ 60.784633] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
[ 60.784721] =====>rtl8192_set_chan()====ch:1
[ 60.901278] =====>rtl8192_set_chan()====ch:2
[ 61.030043] =====>rtl8192_set_chan()====ch:3
[ 61.150028] =====>rtl8192_set_chan()====ch:4
[ 61.270018] =====>rtl8192_set_chan()====ch:5
[ 61.390054] =====>rtl8192_set_chan()====ch:6
[ 61.510029] =====>rtl8192_set_chan()====ch:7
[ 61.630028] =====>rtl8192_set_chan()====ch:8
[ 61.750026] =====>rtl8192_set_chan()====ch:9
[ 61.870031] =====>rtl8192_set_chan()====ch:10
[ 61.990021] =====>rtl8192_set_chan()====ch:11
[ 62.110018] =====>rtl8192_set_chan()====ch:12
[ 62.230042] =====>rtl8192_set_chan()====ch:13
[ 62.350654] alg name:WEP
[ 62.362579] ===========>set_swcam():EntryNo is 0,KeyIndex is 0,KeyType is 1,is_mesh is 0
[ 62.362684] Linking with casaSiraW,channel:1, qos:1, myHT:1, networkHT:1, mode:10 cur_net.flags:0x40e
[ 62.362699] Linking with casaSiraW,channel:1, qos:1, myHT:1, networkHT:1, mode:10 cur_net.flags:0x40e
[ 62.362829] ===>rtllib_associate_procedure_wq(), chan:1
[ 62.362832] HTSetConnectBwMode():pHTInfo->bCurBW40MHz:0
[ 62.362834] =====>rtl8192_set_chan()====ch:1
[ 62.374702] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
[ 62.378746] SetHwReg8192SE():HW_VAR_AC_PARAM eACI:0:a42b
[ 62.378749] SetHwReg8192SE():HW_VAR_AC_PARAM eACI:1:a44f
[ 62.378751] SetHwReg8192SE():HW_VAR_AC_PARAM eACI:2:5e4322
[ 62.378753] SetHwReg8192SE():HW_VAR_AC_PARAM eACI:3:2f3222
[ 62.378757] Associated successfully
[ 62.378759] normal associate
[ 62.378767] Using G rates:108
[ 62.378768] Successfully associated, ht enabled
[ 62.378770] HTSetConnectBwMode():pHTInfo->bCurBW40MHz:1
[ 62.378772] =====>rtl8192_set_chan()====ch:3
[ 62.388900] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 62.388904] rtl8192_update_cap(): WLAN_CAPABILITY_SHORT_PREAMBLE
[ 62.390421] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 62.440429] DHCP pkt src port:68, dest port:67!!
[ 62.551486] DHCP pkt src port:68, dest port:67!!
[ 62.940452] dm_check_edca_turbo():iot peer is atheros, bssid:00:27:19:cc:92:52
[ 69.589556] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 69.640080] Scan in 40M, force to 20M first:1, 1
[ 69.640120] =====>rtl8192_set_chan()====ch:1
[ 69.750027] =====>rtl8192_set_chan()====ch:2
[ 69.860058] =====>rtl8192_set_chan()====ch:3
[ 69.970045] =====>rtl8192_set_chan()====ch:4
[ 70.080052] =====>rtl8192_set_chan()====ch:5
[ 70.191269] =====>rtl8192_set_chan()====ch:6
[ 70.311275] =====>rtl8192_set_chan()====ch:7
[ 70.430033] =====>rtl8192_set_chan()====ch:8
[ 70.540029] =====>rtl8192_set_chan()====ch:9
[ 70.650028] =====>rtl8192_set_chan()====ch:10
[ 70.760023] =====>rtl8192_set_chan()====ch:11
[ 70.870025] =====>rtl8192_set_chan()====ch:12
[ 70.980032] =====>rtl8192_set_chan()====ch:13
[ 71.090063] Scan in 20M, back to 40M
[ 71.090071] =====>rtl8192_set_chan()====ch:3
[ 71.100322] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 71.100326] rtl8192_update_cap(): WLAN_CAPABILITY_SHORT_PREAMBLE
[ 72.991266] wlan0: no IPv6 routers present
[ 110.190465] LPS leave: notify AP we are awaked ++++++++++ SendNullFunctionData
[ 110.190577] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 110.250192] Scan in 40M, force to 20M first:1, 1
[ 110.250232] =====>rtl8192_set_chan()====ch:1
[ 110.361404] =====>rtl8192_set_chan()====ch:2
[ 110.480055] =====>rtl8192_set_chan()====ch:3
[ 110.590054] =====>rtl8192_set_chan()====ch:4
[ 110.701284] =====>rtl8192_set_chan()====ch:5
[ 110.820153] =====>rtl8192_set_chan()====ch:6
[ 110.930212] =====>rtl8192_set_chan()====ch:7
[ 111.040065] =====>rtl8192_set_chan()====ch:8
[ 111.150139] =====>rtl8192_set_chan()====ch:9
[ 111.260145] =====>rtl8192_set_chan()====ch:10
[ 111.371389] =====>rtl8192_set_chan()====ch:11
[ 111.490142] =====>rtl8192_set_chan()====ch:12
[ 111.601283] =====>rtl8192_set_chan()====ch:13
[ 111.720051] Scan in 20M, back to 40M
[ 111.720058] =====>rtl8192_set_chan()====ch:3
[ 111.730302] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 111.730308] rtl8192_update_cap(): WLAN_CAPABILITY_SHORT_PREAMBLE
[ 116.790187] usb 6-2: USB disconnect, address 2
[ 151.210142] usb 6-2: new full speed USB device using uhci_hcd and address 3
[ 151.393601] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input9
[ 151.393899] generic-usb 0003:09DA:054F.0003: input,hiddev96,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1d.1-2/input0
[ 151.397081] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.1/input/input10
[ 151.397260] generic-usb 0003:09DA:054F.0004: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1d.1-2/input1
[ 162.790186] usb 6-2: USB disconnect, address 3
[ 164.471302] rtl8192_hw_wakeup(): RF Change in progress! schedule wake up task again
[ 164.634663] psmouse.c: TouchPad at isa0060/serio1/input0 lost sync at byte 1
[ 164.658541] psmouse.c: TouchPad at isa0060/serio1/input0 - driver resynched.
[ 170.192020] LPS leave: notify AP we are awaked ++++++++++ SendNullFunctionData
[ 170.192132] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 170.250203] Scan in 40M, force to 20M first:1, 1
[ 170.250243] =====>rtl8192_set_chan()====ch:1
[ 170.361389] =====>rtl8192_set_chan()====ch:2
[ 170.481396] =====>rtl8192_set_chan()====ch:3
[ 170.600159] =====>rtl8192_set_chan()====ch:4
[ 170.710149] =====>rtl8192_set_chan()====ch:5
[ 170.820152] =====>rtl8192_set_chan()====ch:6
[ 170.930178] =====>rtl8192_set_chan()====ch:7
[ 171.050154] =====>rtl8192_set_chan()====ch:8
[ 171.161402] =====>rtl8192_set_chan()====ch:9
[ 171.281396] =====>rtl8192_set_chan()====ch:10
[ 171.401276] =====>rtl8192_set_chan()====ch:11
[ 171.521385] =====>rtl8192_set_chan()====ch:12
[ 171.640147] =====>rtl8192_set_chan()====ch:13
[ 171.750156] Scan in 20M, back to 40M
[ 171.750163] =====>rtl8192_set_chan()====ch:3
[ 171.760409] ===>rtl8192se_link_change():ieee->iw_mode is 2
[ 171.760415] rtl8192_update_cap(): WLAN_CAPABILITY_SHORT_PREAMBLE
[ 171.890151] usb 6-2: new full speed USB device using uhci_hcd and address 4
[ 172.073249] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input11
[ 172.073522] generic-usb 0003:09DA:054F.0005: input,hiddev96,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1d.1-2/input0
[ 172.076082] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.1/input/input12
[ 172.076276] generic-usb 0003:09DA:054F.0006: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1d.1-2/input1
[ 180.040200] usb 6-2: USB disconnect, address 4
[ 190.520072] usb 6-2: new full speed USB device using uhci_hcd and address 5
[ 190.703265] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.0/input/input13
[ 190.703534] generic-usb 0003:09DA:054F.0007: input,hiddev96,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:1d.1-2/input0
[ 190.706059] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1d.1/usb6/6-2/6-2:1.1/input/input14
[ 190.706249] generic-usb 0003:09DA:054F.0008: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:1d.1-2/input1
|
