| garyczek |
11-21-2006 04:52 PM |
ICH6M SATA Controller works weird - No DMA
Hi, I have problem with my notebook Fujitsu-Siemens V8010. It has Intel ICH6M chipset with SATA Controller. And SATA II disk Fujitsu MHT2040BH with NCQ. If there is request on disk, iowait time of CPU gets to 100% and whole system gets totally unresponsible.
My notebook details:
CPU: Intel Celeron M 1,4GHz
MEM: 256MB 333MHz
HDD: Fujitsu MHT2040BH SATA II, NCQ, 5400rpm, 8MB buffer
SWP: 512MB swap partition
Chipset: ICH6M 82801FBM
GPU: Intel i915GM integrated
kernel: 2.6.19-rc5
dmesg:
Code:
[ 12.746000] ata_piix 0000:00:1f.1: version 2.00ac6
[ 12.746000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 12.746000] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 12.746000] ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0x1810 irq 14
[ 12.746000] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 12.746000] scsi0 : ata_piix
[ 13.049000] ata1.00: ATAPI, max UDMA/33
[ 13.201000] ata1.00: configured for UDMA/33
[ 13.201000] scsi1 : ata_piix
[ 13.201000] ata2: port disabled. ignoring.
[ 13.201000] ATA: abnormal status 0xFF on port 0x177
[ 13.204000] scsi 0:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4243N 1.03 PQ: 0 ANSI: 5
[ 13.206000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 13.206000] Uniform CD-ROM driver Revision: 3.20
[ 13.206000] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 13.206000] ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ]
[ 13.206000] ata_piix 0000:00:1f.2: invalid MAP value 128
[ 13.206000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 13.206000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 13.206000] ata3: SATA max UDMA/133 cmd 0x2088 ctl 0x2082 bmdma 0x18B0 irq 19
[ 13.206000] ata4: SATA max UDMA/133 cmd 0x18A8 ctl 0x180E bmdma 0x18B8 irq 19
[ 13.206000] scsi2 : ata_piix
[ 13.359000] ata3.00: ATA-7, max UDMA/100, 78140160 sectors: LBA48 NCQ (depth 0/32)
[ 13.359000] ata3.00: ata3: dev 0 multi count 16
[ 13.362000] ata3.00: configured for UDMA/100
[ 13.362000] scsi3 : ata_piix
[ 13.513000] ATA: abnormal status 0x7F on port 0x18AF
[ 13.514000] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHT2040B 0000 PQ: 0 ANSI: 5
[ 13.514000] SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
[ 13.514000] sda: Write Protect is off
[ 13.514000] sda: Mode Sense: 00 3a 00 00
[ 13.514000] SCSI device sda: drive cache: write back
[ 13.514000] SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
[ 13.514000] sda: Write Protect is off
[ 13.514000] sda: Mode Sense: 00 3a 00 00
[ 13.514000] SCSI device sda: drive cache: write back
[ 13.514000] sda: sda1 sda2 sda3
[ 13.574000] sd 2:0:0:0: Attached scsi disk sda
[ 13.880000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 13.880000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 13.880000] ide0: I/O resource 0x1F0-0x1F7 not free.
[ 13.880000] ide0: ports already in use, skipping probe
[ 13.880000] ide1: I/O resource 0x170-0x177 not free.
[ 13.880000] ide1: ports already in use, skipping probe
hdparm:
Code:
gary@ntb:~$ sudo hdparm -tT -d1 -v /dev/sda
/dev/sda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Inappropriate ioctl for device
IO_support = 0 (default 16-bit)
readonly = 0 (off)
readahead = 256 (on)
geometry = 4864/255/63, sectors = 78140160, start = 0
Timing cached reads: 1920 MB in 2.00 seconds = 960.43 MB/sec
Timing buffered disk reads: 88 MB in 3.02 seconds = 29.11 MB/sec
average buffered disk: 22 MB/sec
maximal buffered disk: 34 MB/sec
On cnet is said that this hdd has maximum internal data transfer rate (how fast it can actually pull data off the disk surface) of 53.9 MBps.
lshw:
Code:
gary@ntb:~$ sudo lshw -class ide -class storage -class disk
*-storage
description: Mass storage controller
product: PCIxx21 Integrated FlashMedia Controller
vendor: Texas Instruments
physical id: 9.3
bus info: pci@06:09.3
version: 00
width: 32 bits
clock: 33MHz
capabilities: storage bus_master cap_list
configuration: driver=tifm_7xx1
resources: iomemory:b0106000-b0107fff irq:17
*-ide
description: IDE interface
product: 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller
vendor: Intel Corporation
physical id: 1f.1
bus info: pci@00:1f.1
logical name: scsi0
version: 04
width: 32 bits
clock: 33MHz
capabilities: ide bus_master emulated
configuration: driver=ata_piix
resources: ioport:1810-181f irq:18
*-cdrom UNCLAIMED
description: SCSI CD-ROM
product: RW/DVD GCC-4243N
vendor: HL-DT-ST
physical id: 0.0.0
bus info: scsi@0:0.0.0
version: 1.03
capabilities: removable
configuration: ansiversion=5
*-storage
description: SATA controller
product: 82801FBM (ICH6M) SATA Controller
vendor: Intel Corporation
physical id: 1f.2
bus info: pci@00:1f.2
logical name: scsi2
version: 04
width: 32 bits
clock: 66MHz
capabilities: storage ahci_1.0 bus_master cap_list emulated
configuration: driver=ata_piix
resources: ioport:2088-208f ioport:2080-2083 ioport:18a8-18af ioport:180c-180f ioport:18b0-18bf iomemory:b0040c00-b0040fff irq:19
*-disk
description: SCSI Disk
product: FUJITSU MHT2040B
vendor: ATA
physical id: 0.0.0
bus info: scsi@2:0.0.0
logical name: /dev/sda
version: 0000
serial: NR29T5A26VMV
size: 37GB
capabilities: partitioned partitioned:dos
configuration: ansiversion=5
*-volume:0
description: Linux filesystem partition
physical id: 1
bus info: scsi@2:0.0.0,1
logical name: /dev/sda1
capacity: 9538MB
capabilities: primary bootable
*-volume:1
description: Linux swap / Solaris partition
physical id: 2
bus info: scsi@2:0.0.0,2
logical name: /dev/sda2
capacity: 517MB
capabilities: primary nofs
*-volume:2
description: Linux filesystem partition
physical id: 3
bus info: scsi@2:0.0.0,3
logical name: /dev/sda3
capacity: 27GB
capabilities: primary
I have no other idea how to solve this problem. I'm not sure whether disk uses correct driver. Friend told me that it may be solved by increasing RAM (i plan buy additional 1024MB RAM for christmas).
Thanks in advance for every hint. |
