Dual Monitor on Fujitsu Stylistic ST5022D
 

I am trying to get dual monitor support to work on this tablet pc in a clone mode so that I can run presentations from it. However, I can't seem to get the xorg.conf file setup correctly to make it run. What happens is the tablet screen comes up fine, but the LCD does not. There are no errors listed in the log file. Here is the output from lspci and my xorg.conf file.

00:00.0 Host bridge: Intel Corp. 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corp. 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.3 System peripheral: Intel Corp. 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02)
00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 02)
00:1d.0 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corp. 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corp. 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:0a.0 CardBus bridge: O2 Micro, Inc. OZ711M3 SmartCardBus MultiMediaBay Controller
01:0a.1 CardBus bridge: O2 Micro, Inc. OZ711M3 SmartCardBus MultiMediaBay Controller
01:0a.2 System peripheral: O2 Micro, Inc. OZ711Mx MultiMediaBay Accelerator
01:0a.3 CardBus bridge: O2 Micro, Inc. OZ711M3 SmartCardBus MultiMediaBay Controller
01:0c.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
01:0e.0 FireWire (IEEE 1394): NEC Corporation IEEE 1394 Host Controller (rev 01)







# XFree86 4 configuration created by pyxf86config

Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "cursor" "SendCoreEvents"
InputDevice "stylus" "SendCoreEvents"
EndSection

Section "Files"

# RgbPath is the location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
RgbPath "/usr/X11R6/lib/X11/rgb"
FontPath "unix/:7100"
EndSection

Section "Module"
Load "dbe"
Load "extmod"
Load "fbdevhw"
Load "glx"
Load "record"
Load "freetype"
Load "type1"
Load "dri"
EndSection

Section "InputDevice"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# Or if you just want both to be control, use:
# Option "XkbOptions" "ctrl:nocaps"
#
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection

Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection

Section "InputDevice"
Identifier "cursor"
Driver "wacom"
Option "Device" "/dev/ttyS0"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4"
Option "Mode" "Relative"
Option "TopX" "0"
Option "TopY" "0"
Option "BottomX" "24576"
Option "BottomY" "18432"
Option "Threshold" "10"
EndSection

Section "InputDevice"
Identifier "stylus"
Driver "wacom"
Option "Device" "/dev/ttyS0"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4"
Option "TopX" "0"
Option "TopY" "0"
Option "BottomX" "24576"
Option "BottomY" "18432"
Option "Threshold" "5"
EndSection

Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Unknown monitor"
HorizSync 31.5 - 68
VertRefresh 50.0 - 85
Option "dpms"
EndSection

Section "Monitor"
Identifier "Monitor1"
HorizSync 30 - 95
VertRefresh 50-60
Option "dpms"
EndSection


Section "Device"
Identifier "Videocard0"
Driver "i810"
VendorName "Videocard vendor"
BoardName "Intel 852"
BusID "PCI:0:2:0"
Screen 0
EndSection

Section "Device"
Identifier "Videocard1"
Driver "i810"
VendorName "Videocard vendor"
BoardName "Intel 852"
BusID "PCI:0:2:1"
# Screen 1
EndSection

Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection

Section "Screen"
Identifier "Screen1"
Device "Videocard1"
Monitor "Monitor1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1600x1200" "1280x1024"
Viewport 0 0
EndSubSection
EndSection


Section "DRI"
Group 0
Mode 0666
EndSection