LinuxQuestions.org - TVTIME playing video but no sound (Hauppauge hvr-1800)

- Linux - Hardware (https://www.linuxquestions.org/questions/linux-hardware-18/)

- - TVTIME playing video but no sound (Hauppauge hvr-1800) (https://www.linuxquestions.org/questions/linux-hardware-18/tvtime-playing-video-but-no-sound-hauppauge-hvr-1800-a-737572/)

TVTIME playing video but no sound (Hauppauge hvr-1800)

Ok so i just setup my haupaugge hvr-1800 and i am getting no sound out of tvtime and when i try to connect with totem i get Totem is missing a channel list. Really the only thing i care about is getting sound to work in tvtime as i do not need any features that tvtime does not have. Any ideas?
So here is the info i do know

Code:

tveeprom 2-0050: MAC address is 00-0D-FE-27-7F-A0

tveeprom 2-0050: tuner model is Philips 18271_8295 (idx 149, type 54)

tveeprom 2-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)

tveeprom 2-0050: audio processor is CX23887 (idx 42)

tveeprom 2-0050: decoder processor is CX23887 (idx 37)

tveeprom 2-0050: has radio

cx23885[0]: hauppauge eeprom: model=78521

cx25840 4-0044: cx25  0-21 found @ 0x88 (cx23885[0])

cx25840 4-0044: firmware: requesting v4l-cx23885-avcore-01.fw

cx25840 4-0044: unable to open firmware v4l-cx23885-avcore-01.fw

tuner 3-0042: chip found @ 0x84 (cx23885[0])

tda829x 3-0042: could not clearly identify tuner address, defaulting to 60

I have tried to no luck

Code:

modprobe tvaudio

The program tvtime only supports video capture cards that output as is or data that is not encoded in the stream. If the card does not output video and sound as is, you have to use MPlayer, Xine-lib, or VLC.

The following should help setting up the card.

http://www.linuxtv.org/wiki/index.ph...WinTV-HVR-1800

Since it is basically a DVB card, you will also need DVB utilities. I suggest skip tvtime step in the above link and use MPlayer's DVB or TV device feature to use the card.

I do not have the card nor do I have a DVB card, so I can not help you any further.

IMHO, totem is alright but MPlayer is a lot better. MPlayer is significantly more reliable and stable.

If your video card is one of the VDPAU supported cards, hardware decoding for MPEG-1 or MPEG-2 can be done with out consuming too much processing power by the main processor.

thqanks for the info though

here is some more info
dmesg | grep cx

Code:

cx23885 driver version 0.0.2 loaded

cx23885 0000:08:00.0: PCI INT A -> Link[APC6] -> GSI 16 (level, low) -> IRQ 16

CORE cx23885[0]: subsystem: 0070:7801, board: Hauppauge WinTV-HVR1800 [card=2,autodetected]

cx23885[0]: hauppauge eeprom: model=78521

cx25840 4-0044: cx25  0-21 found @ 0x88 (cx23885[0])

cx25840 4-0044: firmware: requesting v4l-cx23885-avcore-01.fw

cx25840 4-0044: unable to open firmware v4l-cx23885-avcore-01.fw

tuner 3-0042: chip found @ 0x84 (cx23885[0])

cx23885[0]/0: registered device video0 [v4l2]

cx23885[0]: registered device video1 [mpeg]

cx23885_dvb_register() allocating 1 frontend(s)

cx23885[0]: cx23885 based dvb card

DVB: registering new adapter (cx23885[0])

cx23885_dev_checkrevision() Hardware revision = 0xb1

cx23885[0]/0: found at 0000:08:00.0, rev: 15, irq: 16, latency: 0, mmio: 0xfd800000

cx23885 0000:08:00.0: setting latency timer to 64

IRQ 16/cx23885[0]: IRQF_DISABLED is not guaranteed on shared IRQs

cx88/0: cx2388x v4l2 driver version 0.0.7 loaded

cx88/0: cx2388x v4l2 driver version 0.0.7 loaded

I have an older Hauppauge card. To get TVTime sound, I have to plug a stereo cable between the card's audio output and the aux input to my system's sound card.

doesnt have an audio output